If a cylinder had an internal diameter of 2 in and operates at a pressure of 300 psig, calculate the force on the ends of the cylinder.

Q: Sketch a free body diagram that can be used to determine a relation between the force that can turn…

A: FBD

Q: Calculate the equivalent stiffness of the system .

A: Given data: Stiffness of the spring having 10 coils, k1 = 8 N/mm. Stiffness of the spring having 5…

Q: Calculate the magnitude of the force acting on the pin at D. Pin C is fixed in DE and bears against…

A: Mechanical Equilibrium: A body is said to be in mechanical equilibrium if it satisfies the following…

Q: 4. The system of knotted cords shown in Fig P-317 support the indicated weights. Compute the tensile…

A: Given data  Given force system in the string

Q: Q3/. The portable floor crane in the automotive shop is lifting a 420 lb engine. For the position…

A:

Q: Find the magnitude of all the elements and tell whether they are in tension or compression.

A:

Q: If the flexural rigidity of the column is doubled, and length of the simply supported column is…

A: Strength of the column is represented by its Euler buckling load (Pcr), Pcr = π2 E ILe2 Where, E =…

Q: 3 cables with same diameter are used to hold the plate. Calculate the tensile loads in all cables if…

A: Givencables with load as  shown below

Q: The wall-crane structure shown in the diagram carries the 25 kN load.

A:

Q: As depicted below, to depress the on-off switch mechanism, a force of 5 N is applied to the handle.…

A: Given Applied load = 5 N To find Force in the switch S

Q: If P is to be 400 N. What is the value of the weight W? В A

A:

Q: the force in member (DF) is equal to.

A:

Q: Calculate the magnitude of the force acting on the pin at D. Pin C is fixed in DE and bears against…

A:

Q: TA 500 Ib buoy, with a 2 ft radius is tied to the bed of a lake using a steel cable. What is the…

A: Mass of the buoy = 500 lb Need to determine the tensile force in the cable.

Q: Calculate the cross-sectional area of the rod. Answer: Arod" mm2 Attempts: 1 of 1 used Part 2…

A: Note: Dear Student! As per our guidelines, we are only allowed to answer three sub-parts of a…

Q: .Calculate the tension in the cable BD in kN. 2.calculate the magnitude of the force in member BC in…

A:

Q: The cords ABC & BD can each support a maximum load of 274 lb. D. 1213 What is the maximum weight of…

A:

Q: A steel rod having a length of 1 m has a crosssectional area of 100 mm^2 Use E = 200 GPa. If it is…

A:

Q: Make an illustration for this problem and label it completely. This lever has a fulcrum that they…

A:

Q: F E 3 ft A C В 4 ft 4 ft 800 lb

A:

Q: Compute the normal force in section 1. Neglect the weights of the member. Note that point B is…

A:

Q: For the figure shown below, compute the normal force in section 1. Neglect the weights of the…

A:

Q: 1. Draw a FBD for the cylindrical tub before the metal object is added, clearly labeling all forces.…

A: When a body is immersed in water , the following forces acts on the body  1) Weight of the body  2)…

Q: A 400-mm-long rod with a diameter of 4.5 mm is loaded with a 5000-N weight. If the diameter…

A:

Q: Question continued... (where the force P1 is equal to 259 lb and the force P2 is equal .to 88 Ib) P1…

A: Given, P1=259 lb,P2=88 lb

Q: calculate the forces on the rod by using the method of joint

A: The free body diagram of the truss is as follows:

Q: Given the image below, what is the magnitude of the equivalent concentrated load of the weight of…

A:

Q: What force applied to a circular cross-section of diameter 7.5in will produce the same pressure with…

A:

Q: Given the image below, what is the correct force diagram that shows the reactions of the supports

A:

Q: Calculate the force the biceps muscle must exert to hold the forearm and its load as shown in…

A: Consider the free body diagram shown below for the arm.

Q: Determine the forces at the contact surfaces A, B and C. Assume frictionless surfaces for all points…

A:

Q: Q6/A: The crate in figure (7) has a weight of 550N. Determine the force in each supporting cable.

A: Consider the free body diagram of the joint at point A. The weight of the block is

Q: Problem 2: A hydraulic press has a ram of 20 cm diameter and a plunger of 3 cm diameter. It is used…

A:

Q: Q2: The tool shown in Fig.2 is used in a gluing operation to press a thin laminate to a thicker…

A:

Q: Compute for the value of the item required: 1. Vertical Reaction at D 2. Horizontal Reaction at D…

A: Let FG be the force in the member G. Let as represent the weight of the block as "W". ⇒W= 800 lb…

Q: A round brass rod 30 mm in diameter and 200 mm long is subjected to a compressive force of 100 kN.…

A:

Q: 60 mm, 60 mm A R=75 mm 105 mm 100 N

A:

Q: The first step to determine the amount of force T is;

A: Free Body diagram . Whenever we deal with the problem of mechanics ,most of the problem's first step…

Q: Question # 2: Determine the force in each of the three cables needed to lift the ma that has a…

A: Givenweight of the macchine W=10kN

Q: A) Calculate the tension in the wire and the reaction force (magnitude and direction) for the sign…

A:

Q: find the weight of the wooden beam shelf attach on the wall.

A:

Q: The structure shown in Fig(1) consists of 8 650 kN members. Determine the force supported by each…

A: For the Given truss  To determine  force supported by each member using method of joints

Q: 1. Compute for the force in each member of the truss in figure 1.

A:

Q: 3. The block as shown in Figure 3.6 has a weight of 250 N, which is inclined at 30° to the…

A: Given : W = 250 N µs = 0.6 To find : Frictional force acting at the surface of contact

Q: A bin weighing 15 kips is supported by 3 steel tension rods.  Each rod has a diameter of 1 in.…

A:

Q: Q31. The portable floor crane in the automotive shop is lifting a 420 lb engine. For the position…

A:

Q: 7. Figure 7a shows a semi-conical buttress. Calculate the components of the total force acting on…

A: Given data: ◆ Radius of semi-conical buttress: r = 1.50 m ◆ Height of semi-conical buttress: h =…

Q: Compute all the bar forces in the truss below. Indicate if it is in compression or tension. Retain…

A: TRUSS: Truss is a rigid structure in which all the members are subjected to either axial tensile or…