If a drawing has 6 fillets with radius (1/2 inch) for imperial units drawing, name one way that you can dimension them? Remember the rule for imperial units for leading 0 for anything that is less than 1. Radius shall be in decimal.

Q: Dimension is 3/4” scale is 2”=1” what is the distance?

A:

Q: 1.3 Determine the length of side a and the measure of the two acute angles. 72.0' 67.3'

A: find the side a and two acute angles.

Q: This geometric figure can be divided by a straight line into two parts that together can form a…

A: GIVEN : This geometric figure can be divided by a straight line into two parts that together can…

Q: is this drawing metric or inch?

A: In the given drawing, the screw size is M8 x 1.25 . That means is it 8 mm nominal size screw. That…

Q: Draw the following figure: 50000- 8.0000

A: The drawing of the given figure will be:

Q: 37. Show the tolerance zone for the given slot. Superimpose the tolerance zone on the given drawing.…

A: The tolerance for the offset is

Q: Q3 Draw Front, Top and side view of the drawing shown below. All dimensions in mm and scale 2:1. 18…

A: Orthographic Projection It is a form of presenting a three-dimensional object into Two dimensional.…

Q: What are the two dimensions that are not placed on the field of a drawing? A zero and a 45 degree…

A: The following things needs to be mentioned on the field of drawing: ◆ The diameter or radius of…

Q: The object shows the center of the whole is three inches from the left surface and one inch from the…

A: we have to determine what kind of dimensions are used in the hole

Q: Select one: 0.75 and 0.66 and 0.04 and 1.75 and

A:

Q: the centre distance in mm

A: Given data;  Compound gear train with gears;  p=20 teeth  Q= 40 teeth  R= 15 teeth  S=20 TeethGears…

Q: The given figure shows a casted I shape made from steel. You are required to design a wooden pattern…

A: According to the details provided in the question, we need to create a pattern with steel. First, we…

Q: Determine smaller diameter, All dimensions are in mm) 110.916 091 S 100.916 80.916 mm cant be…

A: The smaller diameter is 80.916 mm.

Q: Calculate to the correct number of significant figures. 1.54 x 0.03060 x 0.69

A: The number of significant figures in the number 1.54 is 3 as all digits are non-zero. The number of…

Q: Draw back the drawing given with the scale 1:1 on the new drawing paper using all the method on…

A: 1. Draw the horizontal reference line using Drafter to a some extent. 2. Draw the vertical…

Q: Draw back the drawing given  with the scale 1:1 on the new drawing paper using all the method on…

A: 1. First off all we need to locate the two points of the given part at distance of 200 mm apart in…

Q: what is the scale if a line is 10 inches but is  drawn 5 inches long.

A: Finding scale if a line is 10 inches but is  drawn 5 inches long.

Q: 1- Redraw the isometric drawing. 2- Add all center lines. 3- Add all necessary dimensions.

A:

Q: Show a scale diagram indicating a reading of 0.206 inch in a micrometer.

A: Given question : Show a scale diagram indicating a reading of 0.206 inch in a micrometer.   The…

Q: Draw the front,top and R.H.S/L.H.S view of the given figure attached below.write the processes too…

A: Orthographic Projection It is a form of presenting a three-dimensional object into Two dimensional.…

Q: The smallest division on the main scale of Vernier calipers is 0.1 cm. Ten divisions of the Vernier…

A:

Q: The engine piston weighs 180 g. The machine speed is 4400 RPM. What is the maximum speed of the…

A:

Q: The smallest division on the main scale of Vernier calipers is 0.1 cm. Ten divisions of the Vernier…

A: True reading=main scale reading+vernier scale division*least count 10 division of vernier scale=9…

Q: Using the rules of projection find the true length of line AB using a 1:5 METRIC scale.

A: Given condition

Q: The figure above shows a section of a vernier protractor. What is the smallest reading (in minutes…

A: i)smallest reading measured that is least count LC=10'5=2'

Q: The height (in mm) for a 125 mm sine bar to measure a taper of 27'32' on a flat work piece (correct…

A: Given:Length of sin bar, L=125 mmθ=27o 32'θ=27+3260oθ=27.533o

Q: An irregular shaped metal sheet is to be constructed with a measurement of 10m x 15m x 20m x 25m. Do…

A:

Q: 7. Fill-up the blanks in the following sentences by appropriate words selected from the list of…

A:

Q: Fill-up the blanks in the following sentences by appropriate words selected from the list of words…

A: As per the regulations of the Company, only three parts will be answered, and for rest of the parts…

Q: Calculate the angles

A: To find: angles made by forces

Q: a) Calculate the area of the plate. A= Number in?

A: Given:

Q: The height of an object would be found on which  of the standard views in a set of drawings

A:

Q: A SHEROID HAS A FIRST ECCENTRICITY OF 0.81427. COMPUTE THE VALUE OF ITS FLATTENING.

A:

Q: Q4 Draw Front, Top and side view of the drawing shown below. All dimensions in mm and scale 1:1.

A: Required Front view, Top view and side view are drawn using first angle method of projections.

Q: What a linear distance would be shown on a drawing if the following dimensions are drawn to the…

A:

Q: find the diameter

A: Given : Dimension of a cylindrical side riser   Height= Diameter 25cm×15cm×5 cm steel casting from…

Q: Question 1: Draw the front view and top view for the given drawing with the dimensions. Use suitable…

A: Orthographic Projection It is a form of presenting a three-dimensional object into Two dimensional.…

Q: Q3 Draw Front, Top and side view of the drawing shown below. All dimensions in mm and scale 2:1. 030…

A: Orthographic Projection It is a form of presenting a three-dimensional object into Two dimensional.…

Q: How do you find the distance if the dimension is 1 5/8 and scale is 3/4= 1 ?

A:

Q: Three dimensional drawing in which all the sides are measured full size and scaled with drawing at…

A: Solution:

Q: a)Draw the multiviews (Front, Top and Left) of the part given below. b) Show the dimensions of the…

A: According to the details provided in the question, we need to draw three standard View

Q: Specify a flatness tolerance of .004 for the top surface of the part in the drawing below. A. B. C.…

A:

Q: a) Create a sketch of the Figure 2 as below (.ipt) b) Extrude the sketch in a) by a thickness of 1mm…

A: According to the details provided in the question, we need to DRAW the figure.  i am using the…

Q: Indicate the number of pieces in Image 1. For example, in the image with a number 2, there are 5…

A: The number of pieces in the given image

Q: For the figure below, all dimensions in inch. A/ The value of Y-bar is

A:

Q: Question 16 Here is a way we can estimate the distance from the earth to the moon. When the moon is…

A: GIVEN DATA- Arc Length AB=6152 miles The radius of earth R=3960 miles We have to find both point…

Q: Draw the three elevations using AutoCAD and put the measurements on the drawing

A: According to the details provided in the question, we need to draw three elevation.

Q: For the figure below, all dimensions in inch. A/[the value of X-bar is

A: