In a stressed body, an elementary cube of stresses equal to 15 kN/cm2 and 9 kN/cm2 are observed on these respective faces. They are also accompanied by shear equal to 4 kN/cm2. The magnitude of the principle stresses at the point are (a) 12 kN/cm2 tensile and 3 kN/cm2 tensile (b) 17 kN/cm2 tensile and 7 kN/cm2 tensile (c) 9.5 kN/cm2 compressive and 6.5 kN/cm2 compressive (d) 12 kN/cm² tensile and 13 kN/cm2 tensile

In a stressed body, an elementary cube of stresses equal to 15 kN/cm2 and 9 kN/cm2 are observed on these respective faces. They are also accompanied by shear equal to 4 kN/cm2. The magnitude of the principle stresses at the point are (a) 12 kN/cm2 tensile and 3 kN/cm2 tensile (b) 17 kN/cm2 tensile and 7 kN/cm2 tensile (c) 9.5 kN/cm2 compressive and 6.5 kN/cm2 compressive (d) 12 kN/cm² tensile and 13 kN/cm2 tensile

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A brief, deep cantilever pillar is 500 mm long by 200 mm deep and is 2 mm thick. It carries a vertically descending load of 35 kN at its end. Expecting that the shear push is consistently dispersed over the cross area of the bar. Which of the following gives the uniform shear strain of the beam in radians if the shear modulus or Modulus of Rigidity G=25000 N/mm^2?
A simply supported rectangular beam of length 6.45m has a width of 437.5 and an effective depth of 692.5. The beam is to be reinforced using 12 mm bars. The beam supports service dead loads of 31 kN/m and 39.5kN/m., respectively. the fc' is 28MPa, fy is 420MPa and Wu is 89.9kN/m. 1. what is the ultimate moment capacity of the beam? 2. what is the height of the equivalent stress block? 3. Determine the number of bars required for this beam
A beam having a span of 4m is subjected to a maximum shear of 20 kN. It has a triangular cross - section having a base width of 140 mm and an altitude of 300 mm. Which of the following gives the maximum shearing stress developed on the beam? a. 1.43 MPa b. 1.80 MPa c. 1.62 MPa d. 1.78 MPa
A simply supported rectangular beam 50 mm wide by 100 mm deep, carries a uniformly distributed load of 1200 N/m over the entire length.1. Which of the following gives the max. length of the beam If the flexural stress is limited to 20 MPa. a. 3.11 m.b. 3.33 m.c. 3.44 m.d. 3.66 m.2. Which of the following gives the max. shearing stress of the beam. a. 0.30 MPab. 0.50 MPac. 0.40 MPad. 0.60 MPa3. Which of the following gives the max. deflection of the beam assuming E = 18000 MPa. a. 24.52 mmb. 25.72 mmc. 26.62 mmd. 28.82 mm
The cantilever beam shown has the following dimensions: a = 300 mm; b = c = 400 mm; d = g = 24 mm; e = g = 96. The loads are ωo = 2 kN/m and P = 3 kN. Determine the maximum bendingstress and the maximum shear stress in the beam.
1. A 75 mm x 75 mm x 8 mm angle is used as a beam over a span of 7.0 m. It is subjected to loading of 10 kN/m acting in the vertical plane passing through the centroid of the Section Determine maximum stress induced in the section.
A shaft composed of segments AC, CD, and DB is fastened to rigid supports and loaded. For bronze, G = 35 GPa; aluminum, G = 28 GPa, and for steel, G = 83 GPa. Determine the maximum shearing stress developed in each segment.
A simply supported wood beam that is 4.2 m long carries a 49 kN concentrated load at B. The cross-sectional dimensions of the beam are b = 130 mm, d = 420 mm, a = 65 mm, and c = 40 mm. Section a–a is located at x = 0.7 m from B.(a) At section a–a, determine the magnitude of the shear stress in the beam at point H.(b) At section a–a, determine the magnitude of the shear stress in the beam at point K.(c) Determine the maximum horizontal shear stress that occurs in the beam at any location within the entire span.(d) Determine the maximum tensile bending stress that occurs in the beam at any location within the entire length.
A simply supported wood beam that is 4.2 m long carries a 49 kN concentrated load at B. The cross-sectional dimensions of the beam are b = 130 mm, d = 420 mm, a = 65 mm, and c = 40 mm. Section a – a is located at x = 0.7 m from B. (a) At section a – a, determine the magnitude of the shear stress in the beam at point H. (b) At section a – a, determine the magnitude of the shear stress in the beam at point K. (c) Determine the maximum horizontal shear stress that occurs in the beam at any location within the entire span. (d) Determine the maximum tensile bending stress that occurs in the beam at any location within the entire length
A simply supported beam has a concentrated load at midspan. If the beam properties are given below, what is the final stress at bottom of the beam section where the maximum moment is located and the total losses of the prestressing force is 21% (MPa) Properties: Beam width = 289 mmBeam height = 498 mmConcentrated load = 22.79 kNSpan of the beam = 9 mPrestressing force = 385 kNeccentricity = 123 mm
A simply supported rectangular beam of length 6.45m has a width of 437.5 and an effective depth of 692.5. The beam is to be reinforced using 12 mm bars. The f'c is 28 and the fy is 420. The beam supports service dead loads of 31 kN/m and 39.5kN/m., respectively. 1. Calculate the ultimate moment capacity of the beam. 2. Calculate the height of the equivalent stress block. 3. Determine the number of bars required for this beam
A simply supported wood beam that is 12.9 m long carries a 30 kN concentrated load at B. The cross-sectional dimensions of the beam are b = 150 mm, d = 380 mm, a = 100 mm, and c = 35 mm. Section a–a is located at x = 2.2 m from B. (a) At section a–a, determine the magnitude of the shear stress in the beam at point H. (b) At section a–a, determine the magnitude of the shear stress in the beam at point K. (c) Determine the maximum horizontal shear stress that occurs in the beam at any location within the entire span. (d) Determine the maximum tensile bending stress that occurs in the beam at any location within the entire length.