In the figure below, the arm CD of the pipe is parallel to the z axis. The cross-section of the pipe AD is shown in the figure. Take d 30 mm and the thickness t-4 mm. For the loading shown. a. Calculate the stresses on point A b. Calculate the stresses on point B.

In the figure below, the arm CD of the pipe is parallel to the z axis. The cross-section of the pipe AD is shown in the figure. Take d 30 mm and the thickness t-4 mm. For the loading shown. a. Calculate the stresses on point A b. Calculate the stresses on point B.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.4.3P: An element on the gusset plate in Problem 7.2-23 in uniuxial stress is subjected to compressive...

See similar textbooks

Related questions

Q: 5. For the system shown below, what steady-state error can be expected for the following test…

Q: 3.- Deduce the expression and determine the mechanical advantage of the mechanism using the graphic…

A: The force acting at C = P

Q: A projectile is fired vertically from point A with an initial speed of 280 ft/sec. Relative to an…

Q: A personal computer is to be examined from a thermodynamic perspective. Determine the direction of…

Q: The beam is supported by a pin at C and by a short link AB. Each pin has a diameter of 14 mm. Assume…

A: Diameter d = 14 mm.Length L = 0.9 mAngle Area is given by,

Q: A double-threaded worm with a lead angle of 20 degrees and axial pitch of 12.7 mm/tooth drives a…

Q: An aluminium hollow box column of square cross section is fixed at the base and free at the top. The…

A: The width of each side, b = 150 mmThe thickness of the column, t = 10 mmThe compressive load, P =…

Q: A refrigerant 22 refrigerating system is operating with a condenser temperature of 42°C and an…

A: Given :Refrigerant used R22Condenser temperature =42oCEvaporating temperature =0oCTo find :(a)…

Q: What are the mechanisms of heat transfer? How are they distinguished from each other?

A: Heat transfer:Heat transfer is a process to transfer the heat from one point to another point within…

Q: A 3 m B 3 m 5 m H 4 m G C 3 m F 3 m 6 kN D 2 m E

Q: The work net available on the surrounding is 12 kJ. Determine the average power produced by a…

Q: Describe the Carnot Principles and briefly discuss the importance.

A: The Carnot Principles or Carnot theorems was created by Nicolas Leonard Sadi Carnot in 1824. This…

Q: If the allowable bearing stress for the material under the supports at A and B is ob = 720 psi,…

A: FBD

Q: Consider a double-fluid manometer attached to an air pipe shown in the figure. If the specific…

Q: Determine the new angular velocity.

A: Moment of inertia about man's center of mass Moment of inertia about woman's center of mass Mass of…

Q: A link in a mechanism is made from round bar. Due to the loading condition, the link is subject to a…

A: Maximum stress is 67 MPa Minimum stress is -27 MPa Required: Stress ratio (R)

Q: Two forces are applied to a rod as shown below and the rod is in rotational equilibrium. The axis of…

A: The given information in the problem is shown in the following attached image:

Q: The uniform blocks A and B weigh 90lb and 60lb, respectively. The coefficients of static friction at…

A: Consider the ground(the grey surface) as surface CFrom the FBD of body A We know, NAB=NBA=49.09 lb…

Q: On its takeoff roll, the airplane starts from rest and accelerates according to a = ao-kv² where ao…

Q: The 3 kg block is initially at rest and pressed against a spring so as to compress it at point A.…

Q: A non-homogenous 50-kg cylinder rests on the bed of a truck. A block prevents it from rolling to the…

A: The mass of the cylinder, m = 50 kgThe acceleration of the truck, a = 8 m/s²The radius of gyration,…

Q: A rotating shaft carries three unbalanced masses of 4 kg, 3 kg, and 2.4 kg at radial distances of 75…

A: The answer is given in the below attachment

Q: A cantilevered beam is loaded as shown. The cross section at the wall is shown, with points of…

A: Cantilever beam loaded with concentrated point load at the free end shown below in figure.F = 1.4 kN…

Q: A 0.4 kg rubber ball has a horizontal velocity of 1.554 m/s at point A and goes through a projectile…

Q: A pulley is supported by a circular pin at A. The pin has a diameter of d = 0.250 in., and each side…

A: When an amount of load act on the object, it has the tendency to change the shape of the object, so…

Q: 5 Answer the following: a) Briefly describe the difference between a bias ply and radial tyre. b)…

A: 5 a)Bias Ply Tyre Construction:-Bias ply tyres are made with reinforcing cord which is laid out…

Q: 1. A device with refrigerant-134a as the working fluid as illustrated in figure attached is used to…

A: Process 1-2s: Isentropic compression process,Process 1-2a: Actual compression process,Process 2-3:…

Q: 2. Consider the closed-loop system shown below. Determine the range of K for stability. Assume that…

Q: D: A thin rod of copper (K=100 w/m K)1.25 cm diameter spans the distance between two parallel plates…

Q: A double-threaded worm with a lead angle of 20 degrees and axial pitch of 12.7 mm/tooth drives a…

Q: FM A B W₁ Wo F₁ FM Y a A B W₁ Br 1 C Wo

A: a=12 cm, b=24 cm and c=36 cmThe angle that the long axis of the tibia makes with the horizontal is…

Q: Water flowing through a pipeline with an internal diameter of 0.4 m moves at a velocity of 0.5 m/s.…

Q: 4" Determine the components of F N F = 5 lb 9" G = 10 lb 6" y

A: F = 5 lb

Q: 4. A residential heat pump has a coefficient of performance of 2.4. How much heating effect in…

Q: Determine the magnitudes and directions of forces acting at pins C and D on member BCD.

A: GivenForce acting on the CD link = 500NFind OutThe Magnitude and Direction of force acting at Pin C…

Q: If the crate in the image weighs 96.1 lb, What is the Force in Cable AD (lb)?

Q: In the plane cage system given in the figure, the external force is P=5 kN, and the lengths of the…

A: In the plane cage system given in the figure, the external force is P=5 kN, and the lengths of the…

Q: Q5:- in the fig M= 20 kg, c=7 N.s/m, k=10 N/M, the excitation is 10 sin5t, find natural frequency,…

A: Given:The mass of the body is The spring constant is .The damping coefficient is .The excitation is…

Q: outline the procedure to determine a plane in a crystal lattice using Miller indices.

A: Miller indices:It is a set of three integers that shows the orientation of a crystal plane or line.

Q: 4.149 Starting from rest, the cart shown is propelled by a hydraulic catapult (liquid jet). The jet…

Q: 11/100 mm in size and 1100 kg/m3 in a cylindrical container with a diameter of 11 m density of 100…

Q: Indoor air dry bulb temperature and relative humidity are 23 C and 45%, respectively. Determine a)…

A: According to our guidelines , we are supposed to answer 1st 3 sub parts . Please re-post other parts…

Q: 4o. kN/m + 'yo 40 Determine the reactions at A and B for the beam subjected to the uniform load…

A: To Find-The reactions at A and B for the beam subjected to the uniform load distribution.Draw the…

Q: An infinitely thin flat plate is operating at a given freestream Mach number of 2.4 where ambient…

A: Mach number = 2.4 Ambient pressure=0.53 atm Angle of attack=4 Required: Lift to drag ratio

Q: Find the moment of inertia shown in the figure Iz a b X

A: There are two bars which have the length:And if the masses are.

Q: A pin-connected truss is loaded and supported as shown. Each aluminum member has a cross-sectional…

Q: A person is 1.65 m tall. a. Calculate the difference in blood pressure between the feet and top of…

Q: NEED HELP WITH D THRUGH G

A: From the free body diagram, evaluate angle .Substitute .

Q: Compressed air with a flowrate of 7 kg/min flows through a two-stage turbine and heat exchanger…

A: mass flow rate m= 7kg/min=7/60 kg/s=0.116 kg/sinitial pressure P1=9barinitial temperature…

Q: Current Attempt in Progress A rectangular bar having width w = 6.25 in. and thickness t= 1.25 in. is…

Concept explainers

Stress transformation

The term stress indicates the measure of internal forces that develop due to an external force's application on an object. When a specific external force is applied to an object, internal stress generates in the material. The value of stress can obtain by taking the ratio of the externally applied force and cross-sectional area of the object. There are different types of stress depending on the type of external force.

Question

In the figure below, the arm CD of the pipe is parallel to the z axis. The cross-section of the pipe AD is shown
in the figure. Take d 30 mm and the thickness t-4 mm. For the loading shown.
a. Calculate the stresses on point A
b. Calculate the stresses on point B.
350 mm
200 N
250 mm
Cross-section of the pipe

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Question Data and Find

VIEW

Step 2: Analysis

VIEW

Step 3: Calculation for torque and bending momnent

VIEW

Step 4: Stresses on A and B

VIEW

Step 5: Stresses on B

VIEW

Solution

VIEW

Step by step

Solved in 6 steps with 8 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

An element on the gusset plate in Problem 7.2-23 in uniuxial stress is subjected to compressive stresses of magnitude 6750 psi. as shown in the figure. Using Mohr’s circle, determine the following. (a) The stresses acting on an element oriented at a slope of 1 on 2 (see figure). (b) The maximum shear stresses and associated normal stresses. Show all results on sketches of properly oriented elements. s
Solve the preceding problem if the normal and shear stresses acting on element B are 56 MPa, 17 MPa, and 27 MPa (in the directions shown in the figure) and the angle is 40° (clockwise).
Through 7.4-25 An clement in plane stress is subjected to stresses x,y, and r. (see figure). Using Mohr’s circle, determine (a) the principal stresses and (b) the maximum shear stresses and associated normal stresses. Show all results on sketches of properly oriented elements. 7.422x=29.5,y=29.5MPa,xy=27MPa
The stresses at a point on the down tube of a bicycle frame are trx= 4800 psi and t = -1950 psi (see figure). It is known that one of the principal stresses equals 6375 psi in tension, (a) Determine the stress (b) Determine the other principal stress and the orientation of the principal planes, then show the principal stresses on a sketch of a properly oriented clement.
The state of stress on an element of material is shown in the figure. Calculate the unit volume change of the element if the stresses x and y. are -20 ksi and 10 ksi, respectively. Assume E = 10,600 ksi and v = 0.33.
The stresses acting on element A on the web of a train rail (sec figure part a) a re found to be 6500 psi tension in the horizontal direction and 18,500 psi compression in the vertical direction (see figure part b), Also, shear stresses with a magnitude of 3800 psi act in the directions shown. Determine the stresses acting on an clement oriented at a counterclockwise angle of 30° from the horizontal Show these stresses on a sketch of an element oriented at this angle
through 7.4-25 An clement in plane stress is subjected to stresses sx,??y,and txy. (see figure). Using Mohr’s circle, determine (a) the principal stresses and (b) the maximum shear stresses and associated normal stresses. Show all results on sketches of properly oriented elements.
An clement in plane stress is subjected to stresses a,. cry, and (see figure). Using Mohr’s circle, determine the stresses acting on an element oriented at an angle 0 from the x axis. Show these stresses on a sketch of an clement oriented at the angle ??. Now. The angle 0 is positive when count ere clockwise and negative when clockwise. r
An clement in plane stress is subjected to stresses a,. cry, and (see figure). Using Mohr’s circle, determine the stresses acting on an element oriented at an angle 0 from the x axis. Show these stresses on a sketch of an clement oriented at the angle 0. Now. The angle 0 is positive when count ere clockwise and negative when clockwise.
Acting on the sides of a stress element cut from a bar in uniaxial stress are tensile stresses of 10,000 psi and 5000 psi, as shown in the figure. (a) Determine the angle 0 and the shear stress T and show all stresses on a sketch of the element. (b) Determine the maximum normal stress amaxand the maximum shear stress Tmax in the material.
An element in pure shear is subjected to stresses ??xy= 3750 psi, as shown in the figure. Using Mohr’s circle, determine the following: (a) The stresses acting on an clement oriented at a slope of 3 on 4 (sec figure). (b) The principal stresses. Show all results on sketches of properly oriented elements.
An element in plane stress on the surface of an automobile drive shaft (see figure) is subjected to stresses of crv = —45 MPa and rTb = 39 MPa (see figure). It is known that one of the principal stresses equals 41 MPa in tension. (a) Determine the stress (b) Determine the other principal stress and the orientation of the principal planes, then show the principal stresses on a sketch of a properly oriented element.