In this system, the dimension of the part is allowed to vary on both the sides of the basic size

Q: draw the isometric and pictorial figure of the given measurement below

A:

Q: Dimension is 3/4” scale is 2”=1” what is the distance?

A:

Q: 7. A tire gauge registers 32 lbs/in2 when air in a certain tire is at 10°C. After running for a…

A: Given that: The pressure of the air inside the tire is P1 = 32 lb/in2. Before running for a time,…

Q: vity problems_Tóléranc ivity- Problems on Tol

A: given

Q: Enumerate the remaining measurement quantity and Unit

A: Time-si unit second, length-si unit meter, mass-si unit kilogram, electric current-si unit…

Q: Fill in the blank which is given below Linear acceleration is equal to the product of and angular…

A:

Q: Find the ratio of the speed of the driving shaft to the speed of the driven shaft.

A:

Q: Calculate the magnitude

A: The provided force system is shown below.

Q: A spherical balloon is inflated so that its volume is increasing at the ft rate of 9 min How fast is…

A:

Q: A petrol engine has a cylinder diameter and stroke of 120mm and 210 mm respectively. The clearance…

A: Given data, D = 120 mm = 0.12 m L = 210 mm = 0.21 m Vc = 0.00029 m3 Find: V = ?

Q: a 100kg weighting machine with accuracy ±5% full scale, calculate the range of weight that the…

A:

Q: write .687+/- .0003 as a limit dimension

A:

Q: There is a kindof antique bicycle in which the radius of the rear wheel is one-tenth of the front…

A: Rrear=110Rfrontωrear=90ωfrontDistance L=200 feet And L=2πRrear×rotations×RfrontRrear

Q: Dimensions in millimeters forco (in N) of the V.component of the internal nin at D

A:

Q: Determine the mass of a steel ball whose diameter is 16mm.

A:

Q: A flight conveyor of dimensions 3 and 2 ft are moving at a speed of 87 fpm. The conveyor handles…

A:

Q: mine the mass ic weight of a

A: given:specific gravity s=0.85

Q: Air whose density is 0.078 lbm/ft3 enters the duct of an air-conditioning system at a volume flow…

A:

Q: Using only Table A (Conversion of Units), calculate the values asked.  All answers must be given…

A:

Q: train. What is the length of the train and that of the platform in meters, respectively?

A: Given data; Train speed=54 km/hrtime =25 sec for travelling length of train and length of platform…

Q: In the circle, the dimension line originates from. of the circle Periphery Center Radius Chord

A: Dimensioning of a circle can be done by specifying it's radius or its diameter

Q: Determine the total increase in length.

A: Given: E1=175 GPa E2=210 GPa P=55 kN To determine: Total increase in length

Q: 5. If the density of a gas is 0.003 slugs per cubic foot, what is the specific weight of the gas in…

A: Given data,  d= density= 0.003 slug/ft³

Q: of the block if 60 °F (C

A: given:μ=0.76N/sm2m=10kgθ=200y=0.1mm

Q: dimension of the block (in mm) is

A: Given; σ=500ε0.1where,  ε true strain Young modulus= rl is 200 GPa Block thickness=100 mm material…

Q: Compute ly (I bar sub y, in mm“, round-off to 2 decimal places) for the region shown. 80 mm 20 mm 60…

A:

Q: 1. A cantilever machine component, of soli

A:

Q: Express the quantity 254,998m in Km.

A: Given: The quantity is Q=254998 m. The unit conversion factor to convert Meter into Kilometer is, 1…

Q: Express the quantity 254,998m in cm.

A: Given: The quantity is Q=254998 m. The unit conversion factor to convert Meter into Centimeter is, 1…

Q: If the difference in the taped distance and paced distance is 0.90 m and the tape distance is…

A: The relative precision of a measurement is defined as the ratio of the discrepancy in value to the…

Q: Determine final dimension of the block in mm

A: Given data; Flow stress (in MPa) of a material is given by;                       =δ=500ε0.1  Young…

Q: 6. On an engineering drawing a dimension is laid out as 1.760 ± 0.005 A note on the drawing states…

A: (a) The nominal dimension = 1.760 inches. (b) The upper limit = 1.765 inches. (c) The tolerance = ±…

Q: How do you find the distance if the dimension is 1 5/8 and scale is 3/4= 1 ?

A:

Q: How many balls of 50 mm diameter fit in a volume of 4.1 m^3

A:

Q: Using only Table A (Conversion of Units), calculate the values asked.  All answers must be given…

A:

Q: Each cylinder of six cylinder internal combustion engine has a diameter of 60 mm and a stroke length…

A: Given Data Diameter of cylinder is :d=60 mm Stroke length is :L=400 mm No of cylinders is :N=6 Now…

Q: Can you plug in the formula for area show A=

A: Given data  To find the area of the given cross section.

Q: igure Q1(a) shows a gear system. Find The relationship between the number of the gear teeth N1 & N2…

A:

Q: Looking at the x direction, provide the front view, top view, and right-side view using the meter…

A: Find Front view, top view, and right side view with dimensions.

Q: The part denoted by number 1 is the

A: According to the diagram provided in the question. It is cooling system of an automobile engine. The…

Q: Calculate the work for the expansion in the process to 2 decimal places.

A: Thermodynamics : It is a branch of science which deals with work , heat , energy.  Also it studies…

Q: Find the gage block for 86.305 mm dimension.

A: As we know that the standard gauge block(M 122/1) has various block startinv from 1.0005 mm to 100…

Q: A belt is to transmit 50 kW power to a machine. The sheave is 10 inches in diameter and turns at…

A: .Given:  power transmitted→P=50 KW=50000 W Diameter of the driving sheave→D1=10…

Q: (5000 + 600

A:

Q: P1-2) Model the following object. Note that the dimensions are given in millimeters.

A:

Q: What are the dimensions for distances G through M

A: Given data: Orthographic projections are diagrams representing each face of a three dimensional…

Engineering Drawing

Technical drawing has been around since ancient times. As in the ancient Renaissance, complicated drawings were created, including Leonardo da Vinci's drawing. Modern engineering drawing, including its specific orthographic projection with scale conventions, began in Europe (France) during the early stages of Industrialization. L.T. C. Rolt also made some of Marc's drawings for its block-making machinery (in 1799) that also may have contributed significantly to British engineering technology. Since he learned the art of presenting three-dimensional(3D) items in a two-dimensional(2D) plane, as we now term mechanical drawing.