List five thing that are typically removed when removing a transaxle

Q: Applying finger pressure on the belt near the pulley end is the correct method to check the tension…

A: True

Q: Taps are available in sets of 3, Plug, Second & Taper. Which should be used First? M20 17.5mm Plug…

A: There are three types of taps which are to be used in a particular sequence.  1) Taper tap 2) second…

Q: Protects the shaft where it passes through the stuffing box A shaft sleeve B impeller casing…

A: A Shaft Sleeve is cylindrical shape made of metal which is used to protect the Shaft so that the…

Q: The wrong maintenance procedure followed while performing gib adjustment on a lathe machine is O…

A: The correct maintenance procedure for gib adjustment on the lathe machine Adjust the gib to new…

Q: What are the four movement that to be checked in a propeller loose blade

A: given; What are the four movement that to be checked in a propeller loose blade.

Q: You are to draw suitable hydraulic circuit based from the given figure. MAIN RELIEF STATIONARY VALVE…

A: Given : To find : Hydraulic circuit

Q: how to design shaft based on critical speed for agitator?

A: Design of shaft for agitator:- .Tip speed- it is defined by speed of the agitator's blade tip or…

Q: Which part of the drilling machine holds the job while performing drilling operation Select one: O…

A:

Q: -rce. What is the best angle?

A: To find angle.

Q: loaded overhanging

A: ∑MB=0RA*8-10*10-6*9-20*7-20*6-15*4-15-20*3-30*1.5+15*1=0RA=72.375 kN…

Q: 21:compare • Packed Hole Assembly • Pendulum Assembly • Fulcrum Assembly

A: Bottom hole assembly  There are numerous components and equipment (including the drill bit) that are…

Q: Which of the following material is used to connect D Select one: Square box Saddle clip Coupling…

A: Option c is correct.

Q: Sketch the proper end shape of a soapstone that is to beused for marking metal.

A: The design of the work metal is marked with soapstone & chalk line to ensure appropriate…

Q: The following device is used to hold a workpiece securely during drilling in Drilling machine Select…

A: It is required determine which of following device is used to hold a workpiece during drilling…

Q: Name ACTIVITY 10-1 Split Type Dowel 1. 1. Which part has the longest length? 2. Which part has the…

A: 10. How is diameter "A" checked? For industrial application of continuous measurement ring gauge can…

Q: During drilling operation, work piece must be held in vice. Select one: True False

A: Given Statement : During drilling operation, work piece must be held in vice. Select one: True…

Q: A revolving pillar jib cranes can rotate 360° are provided with stops at the end of the jib to…

A:

Q: Write down the name of Primary Control Surface

A: The rudder is a fundamental control surface which is typically controlled by pedals rather than…

Q: tive and compression negative. 45°

A: Draw the free body diagram for the above problem as follows.

Q: If the shaft is always smaller than the hole, general fit name is Fill in the blank with correct…

A: If the shaft is always smaller than the hole, general fit name is_______________. Answer: D)…

Q: ion 3 plain the importance of: rake angle relief angle nose radius

A:

Q: What is a moment of intertia?

A: When an amount of force applied perpendicular to any object then the tendency of that force to…

Q: Draw three views of the adjusting bracket. . Orill-2 Holes 3 BOrill

A: The figure below shows the top and front view of the given model.

Q: bent flat bar rotates

A: θ=πsintθ=30o=π6π6=πsintt=9.6 sec…

Q: Industrial Maint. What are the three types of loads that may be placed on a bearing?

A: The three types of loads that may be placed on a bearing are

Q: Define the drill press center pulley bearing replacement.

A: solution of above problem is below:

Q: The wrong maintenance procedure followed while performing gib adjustment on a lathe machine is On…

A: The engine lathe is a high-precision machine tool that needs to be treated with care. The lathe's…

Q: What is The bearing

A: When two object are in contact and they are moving relative to each than a friction force ulcers…

Q: nance pr Tollowed wniie performing gib adjustment on a lathe machine is O On the front face of the…

A:

Q: 5 inch dia. shafts coupling to connect the equipment shafts. Note: use 4 bolts only nstructions:

A:

Q: Draw three views of the adjusting bracket. Drill-2 Holes Drill PROB. 20 Adjusting bracket.

A: Given isometric view of the adjusting bracket  To sketch the three views  Below the three views are…

Q: List down any four safety precaution need to carry during the operation of Lathe machine.

A: Some safety precautions that need to be followed during the operation of Lathe machines are as…

Q: (7):- The numbers of production elements are a- 9M b- 6M c- 12M d- 5M

A: The total number of production element are ,

Q: orrect

A: GIVEN:

Q: flyw

A: compare governor and flywheel

Q: Safety goggles are required when working on lathe machine. Select one: True False

A: Lathe machine is one of the oldest machine used in manufacturing field. Due to its It's versatile…

Q: Which fixture would be the most suitable for welding up and drilling the holes for fixture for the…

A: Modular fixture is most suitable for welding up and drilling the holes for fixture for the complete…

Q: Helical gear

A: Ans is Helical gear

Q: Which of the following is the front ?view of the figure

A:

Q: aut cad What tool is used to put a radius on an existing intersection? Extend O

A:

Q: teps of how to draw the BUSHING of an IV cannula using SOLIDWORKS

A: A bush, sometimes known as a shrub, is a common plant in both the garden and the wild. Many…

Q: 8.Which of the following pairs is high pair? A sliding pair В cam pair C screw pair

A: Higher pair: When the two elements have point or line contact while in motion then the pair is known…

Q: how can you creat a section view for attached imaje including front side top

A: To create all three views (front view, side view, and top view) are possible only when the isometric…

Q: Which part of the drilling machine holds the job while performing drilling operations? Select one:…

A:

Q: The wrong maintenance procedure followed while performing gib adjustment on a lathe machine is The…

A: Given: The wrong maintenance procedure followed while performing gib adjustment on a lathe machineis

Q: Applying finger pressure on the belt near the pulley end is the correct method to check the tension…

A:

Q: figures sho ed to a con Mat the free

A:

Q: The wrenches are used for clearing burrs from work surfaces. Select one: True False

A: The wrenches are used for clearing burrs from work surfaces. Select one: True False

Buckling of columns

The column is described as a vertical member of the structure that carries an axial compressive load, and buckling is a lateral deformation of the column under the application of load.