lonization interference can occur with alkali metals at relatively low temperature and a. for analyses for other elements at higher temperature b. lonization suppressors decrease the extent o the ionization of analyte lonization suppressors are more easily ionized than the analyte, the large number of electrons produced prevent ionization of the analyte. С. lonization interference occurs when a component of the sample prevents ionization of d. the sample.

lonization interference can occur with alkali metals at relatively low temperature and a. for analyses for other elements at higher temperature b. lonization suppressors decrease the extent o the ionization of analyte lonization suppressors are more easily ionized than the analyte, the large number of electrons produced prevent ionization of the analyte. С. lonization interference occurs when a component of the sample prevents ionization of d. the sample.

Principles of Instrumental Analysis

7th Edition

ISBN:9781305577213

Author:Douglas A. Skoog, F. James Holler, Stanley R. Crouch

Publisher:Douglas A. Skoog, F. James Holler, Stanley R. Crouch

Chapter27: Gas Chromatography

Section: Chapter Questions

Problem 27.5QAP

See similar textbooks

Similar questions

Which of the following is/are true regarding instrumental methods of analysis? a. these methods have higher precision compared to chemical b. these methods have lower throughput compared to classical c. these methods can measure lower analyte concentration than classical d. all of the above
21. (What exactly is meant by potentiometric methods? What are they even?)
What are the necessary conditions for a metal isotope to be useful as a sources in mossbauer spectroscopy.
Explain (with the aid of one or more equations) why a LOWER selectivity coefficient for an interfering ion means an ISE is actually MORE selective for the target ion.
A dual beam UV-visible spectroscopy was used to determine the levels of Fe(II) in the run-off water of a local mine using the ferrozine assay (i) During a check of the instrument a step-like feature at 360 nm was observed in spectrum of the standard. Suggest what may give rise to this with reference to the instrument configuration and comment on how it may be remedied. (ii) The molar absorptivity of the [Fe(Ferrozine)3]2+ complex is 27900 cm−1 M−1 at 562 nm in aqueous solution (pH 5.5). If the EU maximum contaminant level for Fe is 200 ug /L and the contract required detection limit is 100 ug/L, comment on the suitability of the assay for the detection of iron. (iii) Determine the sample range, in terms of concentration and ppm, of Fe(II) that can be confidently analysed by UV-visible spectroscopy using a 1 cm cuvette. Explain with reference to an appropriate equation and solution phenomena, the origin of the limitations that define this range
A 50.00mL sample with BaCl2 was diluted to 650 mL. Aliquots of 100.00 mL of this solution were analysed using Mohr and Volhard methods. The following data were obtained. Volhard method: Volume of AgNO3 = 100mL; Volume of KSCN = 18.25mL Mohr Method: volume of AgNO3: sample = 27.80mL (blank) = 0.30mLWhat is the %BaCl2 using Mohr and Volhard Method. Concentration of KSCN: 0.04000M Concentration of AgNO3: 0.03000M
A stock solution of analyte is made by dissolving 34.83 mg of copper (II) acetate hexahydrate(fw = 289.73 g/mol) in 25.00 mL of water. A second stock solution of internal standard is madeby dissolving 28.43 mg of germanium (I) acetate (fw = 190.74 g/mol) into 25.00 mL of water.These solutions are used to make a series of standards for ﬂame atomic absorption analysiscalibration. The standard solutions (each 10.00 mL total volume) should have the followingconcentrations of copper: 10.00; 25.00; 50.00; 100.0; and 200.0 μM. Each calibration solutionshould also contain 50.00 μM of germanium. What is the analyte stock solution concentration? What is the internal standard stocksolution concentration?Complete this table.
What are the parameters that can be used for analytes identification and quantification using Cyclic Voltammetry, respectively?
1) Compare the techniques of open-path FTIR versus extractive FTIR using gas cells for the analysis of gaseous compounds. Contrast the difference in their instrumentation and analytical procedures and briefly state the analytical applications of each method 2) A Chromophore is___________ 3) The X-ray microanalysimicro analysis technique in a scanning electron microscope involves the transitions of___ 4) What are the radiation sources for Infrared and Near Infrared spectra 5) A typical source for Raman spectroscopy is________
A 20.0 mL sample was analyzed using the Mohr method. Calculate the percent (w/v) Br- (FM = 79.90) if 25.00 mL of 0.1234 M AgNO3 was used to form the yellow-orange endpoint. Group of answer choices 80.9% 4.93% 12.3% 1.23%
i) Find the differences between the AES and XPS in terms of principle and information obtained from the spectra. ii) Why AFM is mostly utilized microscopic method for the determination of the thickness of the film?
Atomic Spectroscopy (a) In terms of spectral shape, how are atomic spectra different from molecular spectra? What is the source of this difference? (b) Describe the decision-making process for picking a line for atomic emission analysis of a given analyte. (c) For quality assurance, spike recovery is not sufficient to establish confidence in an analytical procedure. Explain this statement. What should be done instead to demonstrate satisfactory performance of an instrumental method (including elemental analysis). (d) Find a literature example of atomic spectroscopy used for elemental analysis. State the operating conditions with sufficient detail to reproduce the analysis; Please answer very soon will give rating surely All questions complete Answer needed Please help me