Match each feature control frame to the word or phrase that describes it. Answers are used only once. 1. .009 A BS Feature control frame with too many datum references. 2. e.0200 ABC .003 B Circular runout. 003 ABC 3. Bonus tolerance for LMC is specified. 012 B 4. Composite tolerance. 010 A 5. Shows a cylindrical perpendicularity tolerance zone. 6 0003 Angularity. 004 A 7. A form tolerance. .005 A 8 Shows a former practice; no longer recommended. 9. 0120 A BC Between X & Y specified. 10. .018.250 A BC

Match each feature control frame to the word or phrase that describes it. Answers are used only once. 1. .009 A BS Feature control frame with too many datum references. 2. e.0200 ABC .003 B Circular runout. 003 ABC 3. Bonus tolerance for LMC is specified. 012 B 4. Composite tolerance. 010 A 5. Shows a cylindrical perpendicularity tolerance zone. 6 0003 Angularity. 004 A 7. A form tolerance. .005 A 8 Shows a former practice; no longer recommended. 9. 0120 A BC Between X & Y specified. 10. .018.250 A BC

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

On the part shown, specify a paralellism tolerance to make the top surface parallel to datum A within a total of .002, and with both the profile and parallelism applied to the part above what is the maximum height of the top surface to datum A? Can the MMC Modifier be applied to the feature tolerance? why or why not?
Explain what is represented by the datum feature symbol attached to the feature control frame containing the form geometric tolerance.
For a floating fastener application, a hole size specification of 385" minimum and .395" maximum diameter has a position tolerance specification of .010" diameter MMC. If the position tolerance is changed to .000" diameter MMC, a minimum hole diameter of must be specified with the maximum size limit remaining .395", A. .375 B. .380 C. .385 D. .390
I need help please. Apply a dia 0.5 at MMC straightness control to the axis of the part above and draw the resultant tolerance zone and virtual size on the sketch of the produced part below. The image and question are also attached.
II. Provide complete solutions per problem. No need to copy the problem butprovide the ff format: (a) given (b) required (c)solution 2. A medium force fit on a 75 mm shaft requires a hole tolerance and shaft tolerance eachequal to 0.225 mm and average interference of 0.0375 mm. Find the hole and shaftdimensions.
Draw the block diagram of a Temperature measurement system .Also identify the names of the functional elements used in the measurement system.
Determine tolerance value and limit dimension of the rod which a diameter is ∅127 mm, according to the g6 limit deviation (∅127f6). es=-40.64 mm, ei=-66.04 mm. Determine the basic size, tolerance and limit dimensions.
II. Provide complete solutions per problem. No need to copy the problem butprovide the ff format: (a) given (b) required (c)solution 1. A journal of basic size of 75 mm rotates in a bearing. The tolerance for both the shaftand bearing is 0.075 mm and the required allowance is 0.10 mm. Find the dimensions ofthe shaft and the bearing bore. 2. A medium force fit on a 75 mm shaft requires a hole tolerance and shaft tolerance eachequal to 0.225 mm and average interference of 0.0375 mm. Find the hole and shaftdimensions.
On the drawing attached, before any geometric controls are applied, what is the coaxility tolerance is implied between the diamters?
Draw feature control frame (FCF) of the following characteristics: Profile of line tolerance zone .500 at LMC to datum A Angularity with tolerance zone 0.10 at MMC to datum A at LMC Position tolerance zone .012 in diameter at MMC to datum A, B and C.
The diameters of shafts with a nominal size of dn = 68 mm must be within limits dmax = 68.045 mm and dmin = 68.015 mm. What are the upper deviation es. the lower deviation ei. and the tolerance Td? es ei Td 1) -0.015 +0.045 0.030 2) +0.045 -0.015 0.060 3) +0.045 +0.015 0.030 4) +0.015 -0.045 0.060
Use BS 4500A:1970 to determine the dimensional tolerance on the critical diameters in Gear Sub- assembly. The following tolerance should be determined (the limits and fits at each interface will be provided by Canvas): i. Bush & Shaft: Critical Diameter is 35 mm; (H8/f7) ii. Housing & Bush: Critical Diameter is 45 mm; (H7/s6) iii. Gear & Shaft: Critical Diameter is 20 mm (for the Right Gear) (H7/k6)