Match each of the following terms to the phrase that describes it. Answers are used only once. Matched 1. Technically a detail drawing, although the product is made from more than one piece. Casting 2. Machining 3. Altered-item drawing, for example. Modifying 4. Purchased parts, for example. Welding 5. Control 6 May be combined with the corresponding casting drawing. Development 7. Drawing most needed by a mold maker. Contour 8 Multidetail 9. Two related parts both on the same drawing. 10. Monodetail co

Match each of the following terms to the phrase that describes it. Answers are used only once. Matched 1. Technically a detail drawing, although the product is made from more than one piece. Casting 2. Machining 3. Altered-item drawing, for example. Modifying 4. Purchased parts, for example. Welding 5. Control 6 May be combined with the corresponding casting drawing. Development 7. Drawing most needed by a mold maker. Contour 8 Multidetail 9. Two related parts both on the same drawing. 10. Monodetail co

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

For the casting of the part whose perspective pictures are given below, take into account the surface of the section, the model design, if necessary, the core design, all the molding stages and finally, draw the mold in the most suitable form for casting and name all the mold elements by showing them on the figure (Note: The hole shown in the figure is a full hole. .)
answerDcorrectly.
A grey cast iron block of dimension 200 mm × 100 mm × 10 mm is produced by sand casting . Pattern making allowance is 10 %. What is the ratio of volume of the parttern to volume of the casting.
Please typing answer only IENG 302 - Manufacturing Processes: We are reducing the diameter of a 95.8 mm cylinder to 30.04 mm using 7 roughing passes and 3 finishing passes. The finishing operations use a depth of cut of 1.51 mm. The roughing operations are performed with a feed rate of 9.61 mm/s and the finishing operation is performed with a feed rate of 11.31 mm/s. a) What is the depth of cut for a roughing pass? b) What is the rate of material removal (mm^3/s) for the third roughing pass? c) What is the rate of material removal (mm^3/s) for the final finishing pass? d) What is the average rate of material removal (mm^3/s) for the roughing operations?
For the casting of the part, whose perspective pictures are given below, take into account the surface of the section, the model design, if necessary, the core design, all the molding stages and finally the mold in the most suitable form for casting, and name all the mold elements by showing them on the figure (Note: The hole shown in the figure, full hole.)
104) Which is not one of the methods used to specify geometric features in technical drawing?A) circularityB) fluidityC) sizeD) smoothnessE) tolerance 105) How does aluminum yield strength change as a result of annealing?A) first decreases and then decreasesB) first increases and then decreasesC) increasesD) decreasesE) does not change 106) which gives the stainless steel property?A) chromeB) vanadiumC) molybdenumD) manganeseE) sulfur
Q1. A mold sprue is 20 cm long, and the cross-sectional area at its base is 2.5 cm2 .The sprue feeds a horizontal runner leading into a mold cavity whose volume is 1560 cm3. Determine:(A) velocity of the molten metal at the base of the sprue(B) volume rate of flow(C) time to fill the mold.
Answer the two connected questions (Task A-1 and A-2). Provided in the last part are the guides and examples: The process for large-scale manufacture of paper has been largely unchanged for the last 125 years. The pulp and paper industry today is highly capital intensive, and there is an ongoing drive towards process integration, thereby increasing the efficiency of utilization of available process resources. This paper deals with the Kraft process (see Fig. 1) though the general principles described can be extended to other pulping processes. As shown in Figure 1, five water sinks and four water sources are considered for in-plant water reuse/ recycle. Prior to water reuse/ recycle, the network requires a freshwater flow rate of 36,400 tonne/day and generates 37,186 tonne/day of wastewater (sum of the individual sink and source flow rates in Table 1). The freshwater source that is available for service has an impurity concentration (chloride content) of 4.2 ppm, which is higher than…
19 7.Vents are used for releasing hot gases during pouring. Select one: True False
pls put solut1on thank u0
Need help. Please round answers to 3 sig figs
1. Show your complete solution.