| 20 mm 75 mm 10 mm 37.5 mm 37.5 mm

Q: The way to the column where the loading status is seen determine the P load required for the 5 mm…

A: Given that,

Q: Determine the magnitude of the load P that will cause a maximum normal stress of smax = 30 ksi in…

A: Draw the free-body diagram of the structure.

Q: The tension member is fastened together using two bolts, one on each side of the member as shown.…

A: Given data: Diameter of bolt, d = 0.3 in. Shear stress, τ = 12 ksi Normal stress, σ= 20 ksi The free…

Q: If the allowable tensile stress for the bar is 1st2allow = 21 ksi, and the allowable shear stress…

A: Given: The allowable tensile stress for the bar, σall = 21 ksi The allowable shear stress for the…

Q: The rigid beam is supported by the three suspender bars. Bars AB and EF are made of aluminum and bar…

A: Given data: *The cross sectional area of each bar is A = 450 mm2. *The allowable stress of the steel…

Q: If the allowable tensile stress for the bar is (o,) allow = 21 ksi, and the allowable shear stress…

A:

Q: For the connection shown, determine the average shear stress in the 0.75-in.-diameter bolts if the…

A: Given data d=0.75 inP=52 kipsn=5 Here, d is the diameter and P is the load applied.  Here, n is the…

Q: The axial stresses are 12 MPa C in the wood post B and 150 MPa T in the steel bar A as shown below.…

A: Answer: (a) The load P is 70875 N. (b) The minimum diameter for pin C is 22.62 mm. (c) The minimum…

Q: The bell-crank mechanism is in equilibrium for an applied load of F1 = 19 kN applied at A. Assume a…

A:

Q: R7-3. Determine the required thickness of member BC and the diameter of the pins at A and Bif the…

A: Draw the free-body diagram of the beam.

Q: 2. The bar AC is supported by a pin at A and a cable that runs from B to E around the frictionless…

A: Given data: The allowable stress in the cable is, σa=5.2 ksi. The weight of the cylinder is, w=890…

Q: For the given truss system, determine the normal stress in member BE if its cross sectional area is…

A:

Q: Determine the maximum axial force P that can be applied to the bar. The bar is made from steel and…

A: The given bar is critical to two positions:1) At the fillet section2) At the hole sectionAt fillet…

Q: A structural member is fabricated with the cross section show below and is eccentrically loaded with…

A:

Q: 4. A load P is applied concentrically to the bar shown. If the allowable normal stress is 76 ksi,…

A:

Q: Q2/ Segments AB and BC of the assembly below are made from 6061-16 aluminum. If a couple forces P =…

A: As applied force is at some distance from the longitudinal axis. so it generates torque and the…

Q: Members A and B are made of wood and have a thickness t = 6 mm. If member B is subjected to a…

A:

Q: The hanger at B is held by 10 nails against a column. Determine (a) the shear force, V (in N)and (b)…

A:

Q: The bell-crank mechanism is in equilibrium for an applied load of F1 = 16 kN applied at A. Assume a…

A: Given: F1 = 16 kN  a = 330mm, b = 170mm, c = 75mm, and θ = 50° diameter =23 mm  thickness = 35 mm To…

Q: 800 N 45mm 800 N 9. The lapbelt assembly is to be subjected to a force of 800 N. Determine the…

A:

Q: Current Attempt in Progress Rigid bar ABC is supported by a pin at bracket A and by tie rod (1). Tie…

A:

Q: The compound wooden beam is connected together by a bolt at B. Assuming that the connections at A,…

A: Given data: Permissible screw stress,σtper=150MPa Permissible bearing stress for wood, σbper=28MPa

Q: The joint is fastened using two bolts. Determine required diameter of the bolts if the failure shear…

A:

Q: The vertical links (at BD and CE) have a thickness 5.4 and width = 31.2 mm uniform rectangular cross…

A:

Q: B D The rods AB and CD are assumed to be pin connected at A and C. If the cable BD and CD are made…

A: Draw the free body diagram as follows.

Q: The bell-crank mechanism is in equilibrium for an applied load of F1 = 11 kN applied at A. Assume a…

A: GIVEN DATA- F1=11KN DIA. OF PIN d=29mm t=31mm WE HAVE TO FIND SHEAR STRESS IN PIN AND BEARING STRESS…

Q: Determine the maximum compressive stress in the bracket at section a-a when the load P = 25 kN is…

A: Given: The load, P = 25 kN The distance of load acting from one end, x = 300 mm

Q: The tension member is fastened together using two bolts, one on each side of the member as shown.…

A: Please find the answer below

Q: If the allowable tensile stress for wires AB and AC is sallow = 200 MPa, determine the required…

A:

Q: 3 a M The scheme of supporting of the absolutely rigid body is shown in the picture. The minimal…

A: Given data: The value of a is a = 1.6 m. The magnitude of the moment is M = 8 kN-m. The admissible…

Q: 4 mm 37.5 mm 25 mm Determine the maximum axial force P that can be applied to the bar. The bar is…

A:

Q: The hanger is supported using a rectangular pin. Determine the magnitude of the allowable suspended…

A: The answer is below

Q: Q1/ A bracket is supported by means of 4 rivets of the same size. Design the 1.11. Alalka diameter…

A:

Q: The two pieces of wood, 150mm x 200mm, are glued together along the 55° joint. Determine the maximum…

A:

Q: The 3.0-Mg concrete pipe has a center of mass at point G, and is suspended from cables AB and AC.…

A: Given Data Diameter of AB is :dAB=12 mm Diameter of AC is : dAC=10 mm Now draw the force diagram

Q: Determine the maximum allowable load P that can be safely supported by the frame if t = 1.25 in. and…

A: Given data as per the question t=1.25 in b=3.5 in normal failure stress of σfail = 6 ksi Shear…

Q: Ferd plate Q3// Figure.3 show the arrangement of a support bracket where the detachable plate is…

A: Given:Load,W=40 KNYield stress, Syt=160 N/mm2number of bolts,n=6bolt diameter,d=20…

Q: F13-4. Determine the magnitude of the load P that will cause a maximum normal stress of nus = 210…

A:

Q: Two wood members of uniform cross section are joined using a simple glued scarf splice. Determine…

A:

Q: Determine the size of square bearing plates A′ and B′ required to support the loading. Take P = 1.5…

A: The value of the vertical load P is P=1.5 kip. The allowable bearing stress for the plates is sb=400…

Q: The rows of staples AB contained in the stapler is glued together so that the maximum shear stress…

A:

Q: The bars of the truss each have a cross-sectional area of 1.25 in2. Determine the average normal…

A: Cross-section area of the bars = 1.24 in2 P = 6 kiP tan ϑ = 3 / 4  ϑ = tan-1 (3/4) ϑ = 36.87' Take…

Q: Q3) A pillar crane, shown in below, is fastened to the foundation by means of 16 identical bolts…

A:

Q: The boom DF of the jib crane and the column DE have a uniform weight of 750 N/m. If the hoist and…

A:

Q: Q: The compound wooden beam is connected together by a bolt at B. Assuming that the connections at…

A:

Q: If the allowable tensile stress for the bar is (ot)allow = 22.6 ksi, and the allowable shear stress…

A:

Q: The right-angle bar is supported by a pin at B and a roller at C. what is the maximum safe value of…

A:

Q: 0mm wide inside and 30 mm wide outside. Thickness s 60 mm. The crane hook carries a vertical load of…

A:

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.