Part A Find the average power supplied by the voltage source in the circuit in the figure if v, = 25 cos 10ºt V. Express your answer with the appropriate units. • View Available Hint(s) HA P = Value Units Figure 1 of 1 Submit Part B 40 N Find the reactive power supplied by the voltage source in the circuit. 25 nF 80 µH Express your answer with the appropriate units. HE Vg { 60 N HA ? Q = Value Units

Part A Find the average power supplied by the voltage source in the circuit in the figure if v, = 25 cos 10ºt V. Express your answer with the appropriate units. • View Available Hint(s) HA P = Value Units Figure 1 of 1 Submit Part B 40 N Find the reactive power supplied by the voltage source in the circuit. 25 nF 80 µH Express your answer with the appropriate units. HE Vg { 60 N HA ? Q = Value Units

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

An industrial assembly hall is continuously lightedby one hundred 40-W mercury vapor lamps suppliedby a 120-V and 60-Hz source with a power factor of0.65. Due to the low power factor, a 25 percent penaltyis applied at billing. If the average price of 1 kWh is$0.01 and the capacitor’s average price is $50 permillifarad, compute after how many days of operationthe penalty billing covers the price of the power factorcorrection capacitor. (To avoid penalty, the powerfactor must be greater than 0.85.)
A colliery workshop 20mx10m requires an averageillumination of 135 lm/m 2 on the working plane. Allow acoefficient of utilization of 0.45 and a depreciation factor of1.4. The supply is 230-V at 50Hz and the efficiency of each ofthe lamps is 12 lm/W.16. Calculate the electrical power required for thepurpose.A. 8 kW B. 4 kW C. 3 kW D. 7 kW17. Calculate the current required for the purpose.A. 34.3 A B. 21.2 A C. 26.9 A D. 30.4 A
A current source of i(t) = 10 sin(377t + 30◦) A is applied to a single-element load. The resulting voltage across the element is v(t) = −65 cos(377t + 120◦) V. What type of element is this? Calculate its value.
1. Find the average power absorbed by a circuit component that has a voltage of v = 20.3 cos(754t - 10°)V across it when a current i = 15. 6 cos(754t - 30°) mA flows through it. CHOICES: A. 139 mW B. 149 mW C. 159 mW D. 169 mW E. NOTA
Answer the following points in detail and rigorously. Instead of resorting to formulas, develop from basic principles (laws of voltages and currents, definition of electrical power, properties of phasors, among others). f) Suppose you know P and Q for a two-terminal element. What is the power factor of this element? When would you be ahead and when would you be behind? g) Suppose you know the equivalent resistance R and the equivalent reactance X of a two-terminal passive network. What is the power factor of this network? When would you be ahead and when would you be behind?
QA) The apparent power for an electric network was measured and found to be 360.6VAZ-56.34% 1. Determine the power factor of the network and sketch the power triangle. 2. Identify the elements of the network and provide a reason justifying your answer. B) Define the permeability (ur) of the material. If you are required to design IH and I uH inductors, what type of core will you use in your design and why? support your answer by equations.
AC electrical circuit is below: (refer picture below) a. Determine the current flowing in the load. b. If it is desired that the system power factor be 0.9. With system frequency = 50 Hz. Determine how large the capacitor is must be installed? Which one is correct? A/B/others answer A. C = 7.7015 mF B. C = 35.243 µF c. Please Draw all the phasor. Please give complete, details, and correct answer. Please do step by step, draw the phasor Please using handwriting (not typing ). THANK YOU, I WILL GIVE MANY THUMBS UP.
COURSE: Electrical EngineeringSUBJECT: Electrical ApparatusINSTRUCTIONS:• Write the GIVEN with their respective symbols and units.• Do not skip the SOLUTIONS, do it step-by-step with their respective symbols and units• Round up to 3 three decimal places the FINAL ANSWERS and BOX it. PROBLEM: Determine the complex power for the following cases:a. Q = 2000 VAR, pf = 0.9 (leading)b. ????=220 ?,?=1 ??,|?|=40 Ω (inductive)
The voltage vR = 145 sin(100t) V is connected acroos a 1-Ω resistor. Determine the current (RMS) in polar form. Write the magnitude only in four decimal places.
1. A resistor, in series with a 138-microfarad capacitor, is connected to a 60-cycle source. If the voltage drop across the capacitor is 115 volts and the power taken by the circuit is 922 watts, calculate (a) the circuit current, (b) the ohmic value of the resistor, (c) the line voltage, (d) the circuit power factor. Please show complete solution and the circuit diagram. Please round off answers up to the 3rd decimal place. Thank you!
The variable load resistor RL in the circuit shown is adjusted for maximum average power transfer to RL. 1. a) Find the maximum average power.2. b) What percentage of the average power developed by the idealvoltage source is delivered to RL when RL is absorbing maximumaverage power?3. c) Test your solution by showing that the power developed by theideal voltage source equals the power dissipated in the circuit.
The R, L and C circuit has resistance, R=10Ω, inductance, L= 107 milli-Henry and Capacitance, C=80 micro-farad. The supply voltage is 120 Volts-RMS with a frequency of 60 HZ. What is the power dissipated, across the resistor of the circuit in units of Watts?