Part A The pendulum in (Figure 1) consists of a 2-kg disk and slender rods AB and DC which have a mass per unit length of 2 kg/m. Assume d = 0.6 m. Determine the length L of DC so that the center of mass is at the bearing O. Express your answer to three significant figures and include the appropriate units HẢ ? L = 6.39 m Submit Previous Answers Request Answer X Incorrect; Try Again; 3 attempts remaining Figure Part B 1 of 1 What is the moment of inertia of this assembly about an axis perpendicular to the page and passing through point O? Express your answer in kilograms multiplied by squared meter to three significant figures. d 0.5 m- Vo AEO It vec ? Io = 53.46 0.2 m- kg - m?

Part A The pendulum in (Figure 1) consists of a 2-kg disk and slender rods AB and DC which have a mass per unit length of 2 kg/m. Assume d = 0.6 m. Determine the length L of DC so that the center of mass is at the bearing O. Express your answer to three significant figures and include the appropriate units HẢ ? L = 6.39 m Submit Previous Answers Request Answer X Incorrect; Try Again; 3 attempts remaining Figure Part B 1 of 1 What is the moment of inertia of this assembly about an axis perpendicular to the page and passing through point O? Express your answer in kilograms multiplied by squared meter to three significant figures. d 0.5 m- Vo AEO It vec ? Io = 53.46 0.2 m- kg - m?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A borehole drilling machine with a vertical shaft of 60 mm diameter is 500 mm long and is supported in long bearings at its top end. The shaft has Youngs modulus of E = 110 GN/m2. A disc of mass 40 kg is attached to the center of the shaft. The center of the disc is 0.25 mm from the geometric axis of the shaft. Neglecting any increase in stiffness due to the attachment of the disc to the shaft, calculate: 1.1. The critical speed of rotation. 1.2. The maximum bending stress when the shaft is rotating at 80% of the criticals peed.
Show complete solutions and figures The diameters of the two cylinders A and B in the figure shown are 80 mm and 750 mm, respectively. The face of the piston is 1.2 m above the face of the weight platform. The space in between the piston and the weight is filled with oil (s.g.=0.80). If F=75 N, Determine the following: the value of Wrequired to maintain equilibrium. a) 38.6 N b) 86.3 N c) 63.8N d) 83.6 N e) None
The concrete graviy" dam is heid in place by its awn weight (Egute.1) The density of concrote is pc=2.5Mg/m2 and water has a density of ρw=1.0Mg/m3. Suppose that a=1⋅m ,h=8 m Figure Part A Determinn the setillest dimension d that will prevent the dam hom overturning about is end A. Express your answer to three significant figures and include the appropriate units: d=_______
A uniform horizontal pipe weighing 10 kg and 1.5 m long is used as a lever. If you need to balance two objects (one on each end), where should the fulcrum be placed? The objects weigh 25 kg and 52 kg. What is the reaction force exerted by the support on the pipe? Draw the complete diagram to describe your final answer (include the lengths).
A 10 m steel beam of mass 1000 kg extends 4 m beyond the edge of a flat roof. If a 2,000 kg object is placed on the beam 2 m beyond the roof edge and then to balance the beam a load of 750 kg must be placed on roof at _____ from the edge.
In the need for a standby electric power unit due to frequent power outages, a 500 kW diesel generator set weighing 5,000 kg was selected for the service. The diesel engine drive is rated 670 hp at 1,800 rpm, 6-cylinder, and a base length of 3.8 meters and width of 1.5 meters. After computing the weight of the foundation, considering the soil bearing capacity is 5,000 kg/m², determine the require base area.
A uniform beam that 10-m long is being supported by two men, one man at each end. The weight of the beam. Is 100-N. If the first man supporting at the right side exert twice as much as the second man on the left, where must a 50-N motor be placed (measured from the first man) on top of the beam? Show complete solution.
First it’s the information the screenshot is the question based on the information Typed!!! A 22 m boom of weight 540 N and uniform density is pivoted on one end and supported by a cable at the three- quarter point 16.5 m from the pívot. The boom hangs at angle 50 degrees above the horizontal, and the cable is perpendicular to the boom. An object of weight 2207 N hangs on another cable attached to the boom’s free end.
Four 10 kg masses are being supported by an 800mm solid rod. The rod is being supported at both ends, and the rest of the rod is suspended. Determine the smallest rod diameter to support the masses without bending the rod. Assume the Tensile Strength of the Rod material is 500 MPa
A tall open-topped standpipe has an inside diameter of 3020 mm and a wall thickness of 8.6 mm. The standpipe contains water, which has a mass density of 1,000 kg/m3.(a) What height h of water will produce a circumferential stress of 18.3 MPa in the wall of the standpipe?(b) What is the axial stress in the wall of the standpipe due to the water pressure?
The figure shows a mechanical model of the Russel fracture traction device and the leg. The leg is held in balance in the position indicated by the two weights attached to the two cables. The total weight of the leg and the cast is W=200 N. The horizontal distance between points A and B where the cables are attached to the leg is L=100 cm and the vertical distance is d=10 cm . Point C is the center of gravity of the cast and leg at three quarters of the L measured from point A ( 3L/4= 75 cm) . The angle that cable 2 makes with the horizontal is measured as β=40 ° . Accordingly, in order for the leg to remain in balance in the position shown; a) Find the tensile force T 1 in cable 1 . (Write your result in N ) b) Find the tensile force T 2 in cable 2 . (Write your result in N ) c) Find the angle α of cable 1 with the horizontal
A 15,000 N crane pivots around a friction-free axle at its base and is supported by a cable making a 25∘ angle with the crane (Figure 1). The crane is 16 m long and is not uniform, its center of gravity being 7.0 m from the axle as measured along the crane. The cable is attached 3.0 m from the upper end of the crane. 1. When the crane is raised to 55∘ above the horizontal holding an 11,000 N pallet of bricks by a 2.2 m very light cord, find the tension in the cable. 2. Find the horizontal component of the force that the axle exerts on the crane.