Answered: Plot the temperature distribution along…

Plot the temperature distribution along the fin using the following data: k = 168 W/m.K, h = 12 W/m2.K, a = 0.05 m, b = 0.01 m. Vary x from 0 to 0.1 m in increments of 0.01 m.

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter4: Numerical Analysis Of Heat Conduction

Section: Chapter Questions

Problem 4.3P

See similar textbooks

Related questions

Q: The fin shown in Figure, has a base maintained at 300 C and is exposed to the convection environment…

A: Given: k=1 W/mK h=40 W/m2K T∞=20°C Tb=300 To Find: Node temperatures Heat loss

Q: A composite wall is formed of a 2.5-cm copper plate (k = 386 W/m.°C), a 3.2-mm layer of 0.038…

A: Note:As per our guidelines we are supposed to answer only one question. Kindly repost other…

Q: 7- Consider a composite structure shown on below. Conductivities of the layer are: kl = k3 = 10…

Q: Steel railroad tracks are laid when the temperature is -5.0 °C. A standard section of rail is then…

Q: The exhaust duct from a heater has an inside diameter of 114.3 mm with ceramic walls 6.4 mm thick.…

A: Conduction heat transfer occurs due to direct contact with bodies. Due to it heat flows from hotter…

Q: A steel rod, 12 mm in diameter, passes centrally through a copper tube 2.5 m long and having 36 mm…

A: To find: The stress in copper and steel after rise of temperature. Given: The diameter of steel rod…

Q: 3.1 Which of the listed boundary conditions is NOT one that is commonly used for fin analysis? a)…

A: Given Fin analysis To find Uncommon boundary condition

Q: Q5: The piston cylinder device (radius =10 cm) contains a liquid with a pressure 100 kpa and…

Q: Blowtorch is used to connect the two pipes together. Length of the pipe section shown is 80 cm with…

A: Given: l=0.8m; d=0.7m; t=3mm; k=177 W/m2K; ambient temperature is 25 C; h=20 W/mK; Tb=220 C

Q: 443. Heat Loss from a Buried Pipe A water pipe whose wall temperature is 300 K has a diameter of 150…

A: Given:

Q: It is necessary to insulate a flat surface so that the rate of heat loss per unit area of this…

A: Given, QA=450 W/m2 ∆T=400 K

Q: 2A wall is constructed of 2.0 cm of copper, 3.0 mm of asbestos sheet [k = 0.166 W/m.°C], and 6.0 cm…

Q: A 100 mm diameter steam pipe is covered by two layers of lagging (insulation). The inside layer is…

A: Given dataDiameter of the pipe D= 100mmThickness of the inside layer t1 = 40mmThermal conductivity…

Q: A body having a cylindrical shape of length equals to 1.9 m and diameter equals to 400 mm is inside…

A: During unsteady heat transfer, it is not the only temperature of the body that keeps on changing…

Q: A thick-walled tube of stainless steel [18% Cr, 8% Ni, k=19 W/m.°C] with 2 cm inner diameter (ID)…

A: given;

Q: A steel pipe (k = 45.0 W/m-K) having a 0.05m O.D is covered with a 0.042 m thick layer of magnesia…

Q: A dormitory at a large university, built 50 years ago, has exterior walls constructed of L, =…

A: Answer: (a) The heat flux through the original walls is 75.51 W/m2. (b) The heat flux through the…

Q: A thick wallet tube of stainless steel (k+10 W/M°C) with 2 cm inside diameter and 4 cm outer…

Q: Does Bi<0.1 really suggest a negligible temperature gradient? A straight fin of uniform circular…

Q: wall, plastered on one face, has a thermal conductance of 0.36 m2 K/W, an inside surface

A: Handwriting.jpg

Q: A hot steam pipe having an inside surface temperature of 250°C has an inside diameter of 8 cm and a…

A: The thermal resistance of a hollow pipe can be calculated using the formula given below as-…

Q: Calculate the thermal resistance of a copper tube with diameter1=0.153 mm diameter2= 0.157 mm and…

A: Styrofoam diameter should be more than diameter 2 (0.157 mm) .it cannot be 0.09 mm ,so it should be…

Q: Problem # 2] Calculate the heat loss through a flat sheet glass 2.0 m (w) x 1.0 m(h) x 5.0mm thick…

Q: A steel rod, 12 mm in diameter, passes centrally through a copper tube 2.5 m long and having 36 mm…

A: To Find : The stress in copper before the rise of temperature. Given : The external diameter of…

Q: motor body is 360 mm in diameter (outside) and 240 mm long. Its surface temperature should not…

A: The fin is thin and long enough so that heat loss from the tip is negligible. All the heat is…

Q: A composite wall is exposed to hot combustion gases as shown in the figure below. There is a thermal…

A: Data given: Temperature of the hot gas 2100 C Heat transfer coefficient of the wall A 100W/m2K…

Q: There is a 1.20-cm-thick stagnant air pocket. A) What thickness of cork would have the same…

A: Given data, (1) Stagnate air pocket t1 = 1.2 cm K1 = 0.023 W/m.k Cork K2 = 0.046 W/m.k t2 =…

Q: A straight fin of rectangular profile ( k = 14 W/m . oC ) , thickness of t= 2 mm and L= 23 mm . The…

A: Given Data: The thermal conductivity of the fin is, k=14 W/m·°C. The thickness of the fin is, t=2…

Q: In a steel tube (thermal conductivity λ=52.9 W/mK , internal diameter di=(=0.098-0.006} m, external…

A: GIven: TO calculate temperature at r.

Q: Q2) A straight rectangular fin has a length of 2.5 cm and a thickness of 1.5 mm protrudes from a…

Q: Window height (0.8 m) and width (1.5 m) consisting of two layers of glass (k = 0.78 W /m Co)…

Q: 76. All surfaces of an infinitely long heating element, having a cross section in the shape of a…

A: The heat conduction of the bar can be solved by using the variable temperature. The given…

Q: A 112 m steel pipe has a 246.4˚C temperature, diameter of 230.8 mm is insulated with a 203.9 mm…

Q: A very long rod 5 mm in diameter has one end maintained at 100 oC. The surface of the rod is exposed…

A: Considering a solid cylinder with conduction and convection the temperature profile gives the…

Q: None of the given

A: This question is from heat transfer. We know the equation of effectiveness of infinite long film.

Q: QI- Consider the composite structure shown in the figure. 1. sketch the equivalent thermal…

Q: There is a 1.20-cm-thick stagnant air pocket. A) What thickness of cork would have the same…

A: Given data: ◆ The thermal conductivity and thickness of stagnant air-pocket: Lair = 1.20 cm = 0.012…

Q: A domestic refrigerator with inner dimensions of 0.7 m by 0.7 m at the base and height 1 m was…

Q: The exhaust duct from a heater has an inside diameter of 114. mm with ceram. The average k =1.52…

Q: Effectiveness of the infinitely long fin shows that. Choose the wrong statement If you increase…

A: Let us discuss about effectiveness in infinite long fin. Answer: None of above

Q: An aluminum bar (6061-T4) is initially 250.00 mm long at a temperature of 50°C. It is placed between…

Q: For each of the following cases, determine an appropriate characteristic length Lc and the…

A: a) Given Diameter, D = 50 mm Area, A = 5 mm² k = 2.3W /m.K…

Q: thermocouple is inside a chamber with black walls. If the air around the thermocouple is 20 oC, the…

A: Handwritten.jpg

Q: A steel rod, which is free to move, has a length of 200 mm and diameter of 20 mm at a temperature of…

Q: Problem: A straight rectangular fin of uniform cross section is connected to a base with constant…

Q: A dormitory at a large university, built 50 years ago, has exterior walls constructed of Ls =…

Q: A wall is constructed of 5.0 cm of copper [k = 400 W/m°C] and 5.0 mm of asbestos sheet [k = 0.17…

A: GIVEN DATA For Copper L=5cm K=400 W/m'C For Asbestos L=5mm…

Concept explainers

Conduction and Convection

When energy travels from one object to another it is said to have undergone heat transfer. Heat transfer is nothing but the transfer of thermal energy or internal energy from one thing to another, like e.g., when a vessel with water, kept on top of a burner, heats up because of the flame underneath it.

Question

Plot the temperature distribution along the fin using the following data:

k = 168 W/m.K, h = 12 W/m².K, a = 0.05 m, b = 0.01 m. Vary x from 0 to 0.1 m in increments of 0.01 m.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1: Write the given data and what is to find.

VIEW

Step 2: Determine the perimeter, fin parameter.

VIEW

Step 3: Temperature distribution calculation is performed as.

VIEW

Step 4: Draw the plot.

VIEW

Solution

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 5 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

1.1 On a cold winter day, the outer surface of a 0.2-m-thick concrete wall of a warehouse is exposed to temperature of –5°C, while the inner surface is kept at 20°C. The thermal conductivity of the concrete is 1.2 W/m K. Determine the heat loss through the wall, which is 10-m long and 3-m high. Problem 1.1
A square silicon chip 7mm7mm in size and 0.5-mm thick is mounted on a plastic substrate as shown in the sketch below. The top surface of the chip is cooled by a synthetic liquid flowing over it. Electronic circuits on the bottom of the chip generate heat at a rate of 5 W that must be transferred through the chip. Estimate the steady-state temperature difference between the front and back surfaces of the chip. The thermal conductivity of silicon is 150 W/m K. Problem 1.6
One end of a 0.3-m-long steel rod is connected to a wall at 204C. The other end is connected to a wall that is maintained at 93C. Air is blown across the rod so that a heat transfer coefficient of 17W/m2 K is maintained over the entire surface. If the diameter of the rod is 5 cm and the temperature of the air is 38C, what is the net rate of heat loss to the air?
A person wearing a heavy parka is standing in a cold wind. Describe the modes of heat transfer determining heart loss from the person's body.
A section of a composite wall with the dimensions shown below has uniform temperatures of 200C and 50C over the left and right surfaces, respectively. If the thermal conductivities of the wall materials are: kA=70W/mK,kB=60W/mK, kC=40W/mK, and kP=20W/mK, determine the rate of heat transfer through this section of the wall and the temperatures at the interfaces. Repeat Problem 1.34, including a contact resistance of 0.1 K/W at each of the interfaces.
The heat conducts through the shape below. The temperature of the right face is 93 °C, while the left face is at 23 °C. If the top and bottom faces are completely insulated, and the thermal conductivity of the material decreases with decreasing temperature. * Assume that the thermal conductivity is 100 at 23, decreased to 10 at 93. A) Sketch the temperature profile inside the plate. B) If both sides of the plate in the above problem is exposed to air: Left side (h = 20 W/m2K, TL = 20 °C) and right side (h = 90 W/m2K). Calculate the temperature of the air on the right side.
In order to reduce the heat loss through a large furnace wall, the decision has been made to add external insulation. Calculate the thickness of insulation required to reduce the heat loss by 75%. Before the change is made, no outer steel shell is used.Data: Refractory brick and wall brick:k = 0.87 W m-1 K-1Insulation: k = 0.090 W m-1 K-1•Steel: k = 43 W m-1 K-1h = 55 W m-1 K-1 (inside furnace).h = 11 W m-1 K-1 (outside furnace).
A steel rod (k = 30 W/m degree) 1 cm in diameter and 7 cm long protrudes from a wall which is maintained at 100 degree Celsius. The rod is insulated at its tip and is exposed to an environment with h = 50 W/m2 degree and t a = 30 degree Celsius. Calculate the fin efficiency
What is the rate of heat transfer through a piece of Celotex 3 ft by 8 ft by 1 in. in thickness, if the temp of one surface is 80°F and of the other side is 60°F? thermal conductivity of Celotex in AES = 0.028. Pls determine the temperature gradient and the direction of the heat transfer as well.
A straight fin of rectangular profile ( k = 14 W/m . oC ) , thickness of t= 2 mm and L= 23 mm . The base temperature Tb = 220 oC while the fin is exposed to the environment at 23 oC with h= 25 W/m2 .oC Calculate the heat lost peer meter of fin depth. ( use the chart to calculate the efficiency )
What is the rate of heat transfer, temperature gradient, and the direction of the heat transfer through a piece of Celotex 3 ft by 8 ft by 1 in. in thickness, if the temp of one surface is 80°F and of the other side is 60°F? - thermal conductivity of Celotex in AES = 0.028.
To maximize production and minimize pumping costs, crude oil is heated to reduce its viscosity during transportation from a production field. (1) Consider a pipe-in-pipe configuration consisting of concentric steel tubes with an intervening insulating material. The inner tube is used to transport warm crude oil through cold ocean water. The inner steel pipe (ks= 40 W/m·K) has an inside diameter of Di, 1= 150 mm and wall thickness ti= 20 mm while the outer steel pipe has an inside diameter of Di, 2= 250 mm and wall thickness to=ti. Determine the maximum allowable crude oil temperature to ensure the polyurethane foam insulation (kp= 0.0675 W/m·K) between the two pipes does not exceed its maximum service temperature of Tp, max= 70°C. The ocean water is at ∞ T∞, o= -5°C and provides an external convection heat transfer coefficient of ho= 500 W/m2·K. The convection coefficient associated with the flowing crude oil is hi= 450 W/m2·K. (2) It is proposed to enhance the performance of the…