Print Reading for Industry 354 Class Date Name Industry Print Exercise 17-1 Refer to the print PR 17-1 and answer the questions below. Flange head 1. What type of head does this fastener have? 2. Based on the thread specification, what is the nominal diameter of this fastener? 3. Is the across-the-flats measurement of the head 1.5 times the nominal body diameter? es 73" 4. What is the minimum diameter of the bearing surface of the flange on the head? 3.89 5. What is the total maximum length of this fastener (from head tip to body tip)? .SOT.391.8 6. What is to be applied to a portion of the threads of this fastener? Leckina Caapand Review questions based on previous units: Eall 1: 7. At what scale was the original drawing created? 8. What is the part number that is replaced by this part? 3943 9. What paper size is the original version of this print? 10. What ASME standard is referenced for drawing interpretation? A SME YI4M-1994 be u vile LTA pe al Copyright Goodheart-Willcox Co., In 3 Unit 17 Springs and Fasteners in Industrial Prints 12 Print supplied by H 7-1. Hex Flange Screw. ht Goodheart-Willcox Co., Inc. CHANGES TORQUE VALUES BREAKAWAY TORQUE NOTES: PREVAILING ON TORQUE PREVAILING OFF TORQUE REFERENCE IFI-111 2002 48 IN-LBS MAX 60 IN-LBS MIN 36 IN-LBS MIN 2. REFERENCE IFI-125 2002 .25 MIN 1.50 1.46 .81 MAX CHANGES . 39 MAX 3/8-16 UNC- 2A .650 .618 . 30 .15 15 .36 MIN .5625 .5510 LOCK ING COMPOUND 360 AROUND THREADS ø. 73 MIN 1-DEAS DRAWING INTERPRETATION PER ASME Y14.5M-1994 TOLERANCES UNLESS SPECIFIED t.020 t.010 .005 Hydro-Gear 1411 SO. HAMILTON ST. SULLIVAN, IL 61951 PHONE (217) 728-2581 DATE NAME 00 000 DRAWN CHECKED APPR SIZE SCALE NAME SCREW 01/26/04 SAD 0000 ANGLE FORMER PART NO. த X3947 DRAWN IN INCHES HEX FLANGE HEAD 3/8-16 X 1.50 SHEET 1 OF 1 PART NO. 52137 MATERIAL: GRADE 8 н FULL CHG FINISH: PHOSPHATE AND OIL PROJECT REFERENCE: ZT2800

Question

I need answers to parts 1, 2, and 3, pertaining to the print provided.

Print Reading for Industry
354
Class
Date
Name
Industry Print Exercise 17-1
Refer to the print PR 17-1 and answer the questions below.
Flange head
1. What type of head does this fastener have?
2. Based on the thread specification, what is the nominal diameter of this fastener?
3. Is the across-the-flats measurement of the head 1.5 times the nominal body diameter? es
73"
4. What is the minimum diameter of the bearing surface of the flange on the head?
3.89
5. What is the total maximum length of this fastener (from head tip to body tip)?
.SOT.391.8
6. What is to be applied to a portion of the threads of this fastener?
Leckina Caapand
Review questions based on previous units:
Eall 1:
7. At what scale was the original drawing created?
8. What is the part number that is replaced by this part?
3943
9. What paper size is the original version of this print?
10. What ASME standard is referenced for drawing interpretation?
A SME YI4M-1994
be u vile
LTA
pe
al
Copyright Goodheart-Willcox Co., In
View transcribed image text
Expand
3
Unit 17
Springs and Fasteners in Industrial Prints
12
Print supplied by H
7-1. Hex Flange Screw.
ht Goodheart-Willcox Co., Inc.
CHANGES
TORQUE VALUES
BREAKAWAY TORQUE
NOTES:
PREVAILING ON TORQUE
PREVAILING OFF TORQUE
REFERENCE IFI-111 2002
48 IN-LBS MAX
60 IN-LBS MIN
36 IN-LBS MIN
2.
REFERENCE IFI-125 2002
.25 MIN
1.50
1.46
.81 MAX
CHANGES
. 39 MAX
3/8-16 UNC- 2A
.650
.618
. 30
.15
15
.36 MIN
.5625
.5510
LOCK ING COMPOUND
360 AROUND THREADS
ø. 73 MIN
1-DEAS
DRAWING INTERPRETATION
PER ASME Y14.5M-1994
TOLERANCES
UNLESS SPECIFIED
t.020
t.010
.005
Hydro-Gear
1411 SO. HAMILTON ST. SULLIVAN, IL 61951
PHONE (217) 728-2581
DATE
NAME
00
000
DRAWN
CHECKED
APPR
SIZE SCALE NAME SCREW
01/26/04
SAD
0000
ANGLE
FORMER PART NO.
த
X3947
DRAWN IN INCHES
HEX FLANGE
HEAD 3/8-16 X 1.50
SHEET 1 OF 1
PART NO.
52137
MATERIAL: GRADE 8
н
FULL
CHG
FINISH: PHOSPHATE AND OIL
PROJECT REFERENCE: ZT2800
View transcribed image text
Expand

Expert Answer

Want to see the step-by-step answer?

Check out a sample Q&A here.

Want to see this answer and more?

Experts are waiting 24/7 to provide step-by-step solutions in as fast as 30 minutes!*

*Response times may vary by subject and question complexity. Median response time is 34 minutes for paid subscribers and may be longer for promotional offers.
Tagged in
Engineering
Mechanical Engineering

Other

Related Mechanical Engineering Q&A

Find answers to questions asked by students like you.

Q: per the attacment (zoom in when necessary): for the beam and the loading shown, draw the shear force...

A: The free body diagram of the beam is drawn as bellow,

Q: The figure below shows a turbine-driven pump that provides water to a mixing chamber located dz⁢= 5 ...

A: Click to see the answer

Q: Let FA=100 N and FC= 208.33 N for the shaft below. The shaft is made of 2014 aluminum alloy with yie...

A: a) Consider the free body diagram of the shaft.

Q: I need help solving problems 10, 11, and 12 pertaining to the print provided.

A: Since we question only one question, we will answer the question no. 10. Please submit the question ...

Q: Separate streams of air and water flow through the compressor and heat exchanger arrangement shown i...

A: Click to see the answer

Q: I need help answering questions 7, 8, and 9 pertaining to the print attached.

A: As mentioned in the question, I am solving question no. 13, 14, and 15. Upload the question again up...

Q: consider the cantilevered W14 x 30 beam shown E = 29(103) ksi, I = 291 in4 determine the maximum slo...

A: Show the free body diagram of the beam as in Figure 1.

Q: I need these 3 parts answered. In manufacturing, dimensions often may fall in a range. For example, ...

A: 1-In manufacturing, dimensions often may fall in a range. For example, for three-place decimals, the...

Q: The member is supported by a square rod which fits loosely through the smooth square hole of the att...

A: The force, F1 = 200 N.The force, F2 = 350 N.The force, F3 = 500 N.

Q: I need answers for questions 7, 8, and 9 pertaining to the print provided.

A: 7.Refer the revision history block,The pin in revision A1 is referred to as the ejector pins.

Q: 7. The gas-turbine cycle of a combined gas-steam power plant has a pressure ratio of 12. Air enters ...

A: Given data as per question

Q: I need problems 4, 5, and 6 solved pertaining to the print provided below.

A: Answer to Question no. 4For the four screw threaded holes not marked “A”, an underconstrained tolera...

Q: The figure belows shows three components of an air-conditioning system, where T3= 115°F and m˙3= 1.5...

A: Given data:The temperature, T3 = 115 oF.The mass, ṁ3 = 1.5 lb/s.The specific heat of air, cp = 0.240...

Q: 2.5 lbm of ammonia in a piston-cylinder assembly undergoes a refrigeration cycle consisting of 4 pro...

A: Given data,

Q: M5.19 (Sl units) A GO/NO-GO plug gage will be designed to inspect a 50.00 0.20mm diameter hole. Awea...

A: Calculate the tolerance band.

Q: The figure below provides steady-state data for a throttling valve in series with a heat exchanger. ...

A: Click to see the answer

Q: A piston-cylinder assembly contains 0.49 g of air at a pressure of 150 kPa. The initial volume is 42...

A: Given data as per question

Q: I need answers to questions 4, 5, and 6 pertaining to the print provided. Note: A tutor keeps puttin...

A: Answer to question no. 4The overall dimension of this part (diameter x length) are Ø1.5 units x 1.89...

Q: A piston–cylinder assembly contains 2 lb of water, initially at 100 lbf/in.2 and 400°F. The water un...

A: Given:

Q: I need parts 1, 2, and 3 answered pertaining to the print provided. NOTE: If you refuse to answers a...

A: 1.The company specification number is given in the column.

Q: A heat recovery system​ (HRS) is used to conserve heat from the surroundings and supply it to the Ma...

A: The temperature on mars surface (T1) is 189 K.

Q: 2.26 how do the moment work in this problem. How can they be showed. Draw if possible.

A: As mentioned in the question the value of the moment force P at point B is zero. This indicates that...

Q: True or False: The OFFSET command cannot be used on closed objects

A: The OFFSET command is used to create parallel lines, parallel curves and concentric circles at a cer...

Q: I need problems 2, 3, and 4 answered properly. Problem 1 is already done, it is an example of how th...

A: (2). It is a hole of diameter 0.250 inches and has a depth of 1.000 inches. It is counter-sunk with ...

Q: 5-23 Consider steady one-dimensional heat conduction in a pin fin of constant diameter D with consta...

A: Assumptions:The heat transfer at the tip of the fin is negligible.Only one-dimensional steady heat c...

Q: At the beginning of the compression process of an air standard Otto cycle, p1 = 1 bar, T1 = 300 K. T...

A: Note: We will answer the first 3 subparts since the exact 3 are not specified. Please submit a new q...

Q: I need answers to questions 7, 8, and 9 pertaining to the print provided.

A: To improve the performance of the parts, several changes and inspection are carried out. All the mod...

Q: I need answers for questions 4, 5, and 6 pertaining to the print provided.

A: The overall dimension of the part is,The diameter is 1.5 unitsThe length is 1.892 units.

Q: I need answers to these 3 parts for a review activity.

A: Surface texture symbol placed on the surface or edge of the part feature either directly or using le...

Q: Determine the support reactions of roller A and the smooth collar B on the rod. The collar is fixed ...

A: Consider the free body diagram of the system.RA is the reaction at B and RB and MB are the reactions...

Q: I need answers to parts 10, 11, and 12, pertaining to the print provided.

A: Hii,thanks for the question but there is only 10th  question so we are answeering only 10th question...

Q: 97SD Make freehand sketches of any four (in all) common tools, utensils or pieces of furniture . 1.

A: Table is a furniture. Thus, sketch table:

Q: I need help answering this.

A: 1)  Only one angular dimension is shown on this print  .i.e., 16002) Two  reference dimensions are s...

Q: The stones are thrown off the conveyor with the horizontal velocity of 10 ft/s. Determine the distan...

A: Click to see the answer

Q: The coefficient of static friction between A and C and between B and D is μs = 0.24, and between A a...

A: Consider ND as the normal force by the wall D on block B, fD as the friction force due to surface B,...

Q: 6-70 A 4-cm-diameter shaft rotates at 5200 rpm in a 15-cm-long, 8-cm-outer-diameter cast iron bearin...

A: Given data as per question

Q: I need answers for problems 10, 11, and 12 pertaining to the print.

A: When any dimension enclosed in a parentheses, it will indicates that the given dimension is a refere...

Q: Replace the loading by a single resultant force, specify the location of force measured from point O...

A: Click to see the answer

Q: How much will a beam anchored at one end bend given a uniformly-distributed load along the beam?

A: The schematic diagram of the beam anchored at one end bend given a uniformly-distributed load along ...

Q: A nitriding heat treatment of a BCC steel normally requires 2 h at 600 °C. What temperature would be...

A: Write the given values and constants for the given process:

Q: I need answers to questions 1, 2, and 3 pertaining to the print provided. Note: A tutor keeps puttin...

A: If any changes in the part feature are made, the changes are recorded in the specified format in the...

Q: I need answers to questions 13, 14, amd 15 pertaining to the print provided.

A: As we are entitled to answer only a single question. We’ll answer the question number 13 for you. Pl...

Q: Can any help find the reactions and moments for the these two  problems.  They are somewhat similar ...

A: You have asked two questions at a time and according to the guideline, we do not answer more than on...

Q: I need the answer for number 10.

A: Five Holes, each hole has diameter of 0.500 inches and the holes are equally spaced such that center...

Q: I need this part answered according to the disrections provided in the image.

A: Detailed Drawing:A detailed drawing gives the complete information of the parts depicted on the draw...

Q: Propane is contained in a closed, rigid container with a volume of 10 m^3.  Initially the pressure a...

A: Given:

Q: Problem 3.091 SI Carbon dioxide (CO2) is compressed in a piston–cylinder assembly from p1 = 0.7 ba...

A: Click to see the answer

Q: A mold has a downsprue of length = 20 inch. The cross‑sectional area at the bottom of the sprue is 3...

A: Design of Sprue is,

Q: 4-31 The temperature of a gas stream is to be measured by a thermocouple whose junction can be appro...

A: The characteristics length of the thermocouple is,

Q: An ideal Rankine cycle with reheat uses water as the working fluid. As shown in the figure below, th...

A: Given:

Transcribed Image Text

Print Reading for Industry 354 Class Date Name Industry Print Exercise 17-1 Refer to the print PR 17-1 and answer the questions below. Flange head 1. What type of head does this fastener have? 2. Based on the thread specification, what is the nominal diameter of this fastener? 3. Is the across-the-flats measurement of the head 1.5 times the nominal body diameter? es 73" 4. What is the minimum diameter of the bearing surface of the flange on the head? 3.89 5. What is the total maximum length of this fastener (from head tip to body tip)? .SOT.391.8 6. What is to be applied to a portion of the threads of this fastener? Leckina Caapand Review questions based on previous units: Eall 1: 7. At what scale was the original drawing created? 8. What is the part number that is replaced by this part? 3943 9. What paper size is the original version of this print? 10. What ASME standard is referenced for drawing interpretation? A SME YI4M-1994 be u vile LTA pe al Copyright Goodheart-Willcox Co., In

3 Unit 17 Springs and Fasteners in Industrial Prints 12 Print supplied by H 7-1. Hex Flange Screw. ht Goodheart-Willcox Co., Inc. CHANGES TORQUE VALUES BREAKAWAY TORQUE NOTES: PREVAILING ON TORQUE PREVAILING OFF TORQUE REFERENCE IFI-111 2002 48 IN-LBS MAX 60 IN-LBS MIN 36 IN-LBS MIN 2. REFERENCE IFI-125 2002 .25 MIN 1.50 1.46 .81 MAX CHANGES . 39 MAX 3/8-16 UNC- 2A .650 .618 . 30 .15 15 .36 MIN .5625 .5510 LOCK ING COMPOUND 360 AROUND THREADS ø. 73 MIN 1-DEAS DRAWING INTERPRETATION PER ASME Y14.5M-1994 TOLERANCES UNLESS SPECIFIED t.020 t.010 .005 Hydro-Gear 1411 SO. HAMILTON ST. SULLIVAN, IL 61951 PHONE (217) 728-2581 DATE NAME 00 000 DRAWN CHECKED APPR SIZE SCALE NAME SCREW 01/26/04 SAD 0000 ANGLE FORMER PART NO. த X3947 DRAWN IN INCHES HEX FLANGE HEAD 3/8-16 X 1.50 SHEET 1 OF 1 PART NO. 52137 MATERIAL: GRADE 8 н FULL CHG FINISH: PHOSPHATE AND OIL PROJECT REFERENCE: ZT2800