Prob 2. A FSM has two flip flops with outputs A(t) and B(t) and inputs D(A) and D(B) respectively (as in the previous problem). The FSM has an input I and one output Z (as in the previous problem). The equations for the FSM are given below. The flip flops are positive edge triggered. DA)- (A().Β () + 1 D(B) = B(t) XOR A(t) Z= A+I (XOR = exclusive OR) Initially, at t=0, A(0) = B(0) = 0. Draw the waveforms for the outputs of the flip flops corresponding to A and B and the output Z below, given the waveform for the input I. A B

Prob 2. A FSM has two flip flops with outputs A(t) and B(t) and inputs D(A) and D(B) respectively (as in the previous problem). The FSM has an input I and one output Z (as in the previous problem). The equations for the FSM are given below. The flip flops are positive edge triggered. DA)- (A().Β () + 1 D(B) = B(t) XOR A(t) Z= A+I (XOR = exclusive OR) Initially, at t=0, A(0) = B(0) = 0. Draw the waveforms for the outputs of the flip flops corresponding to A and B and the output Z below, given the waveform for the input I. A B

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Complete questions of c, d, e for this problem notice that the state table from b) is provided d) Design the circuit(s). Explain your reasoning. Draw the final circuit including the flip-flops e) Is your design self-starting? Explain
Perform example number 2: Create a state diagram for the finite- state machine with the state table shown in Table 2. Make a circuit diagram use D flip flop to represent the circuit. Looking forward to your kind response tutor :)
3- Design traffic lights circuit using D type flip flop 4- Design D lip-1lop from T lip-tlop 5- Design SR flip-flop from T flip-lop 6- Design JK ip-flop from T flip-flop 7- Design a logical circuit with two input and output z which perfom the following table
. Design a logic circuit that controls an elevator door in a three-story building. The circuithas four inputs. M is a logic signal that indicates when an elevator is moving (M=1) or stopped (M=0).F1, F2 and F3 are floor indicator signals that are normally LOW, and they go HIGH only when theelevator is positioned at the level of that particular floor. For example, when the elevator is lined uplevel with the second floor, F2=1 and F1=F3=0. The circuit output is the OPEN signal which isnormally LOW and is to go HIGH when the elevator door is to be opened.
9. What is the input equation for D flip-flop for the circuit below?
Topic: Sequential Circuit, Moore-type Circuit, D Flip-flops Modify the circuit below for it to have these equations instead: n = Q1Q0D1 = mQ0 + m'Q1Q0'D0 = m' The modified circuit must still have two D flip-flops.
Design a counter which counts down, with the repeated sequence: (2, 1, 0, 2, 1, 0, …) when the input to the counter circuit is 1. The counter doesn’t count (stays at the same state) when the input is 0. The circuit is to be designed by treating the unused states as don’t care conditions. Fill out state transition table, and draw state diagram and your schematic for the design. Use positive edge D flip flops in your design.
Design a D Flip-Flop using a JK Flip-Flop and basic gates.You have to show the followingi. The conversion tableii. The simplified equation(s) for the flip-flop input(s)iii. The final circuit diagram
14)For the state diagram below a sequential circuit has 2 D -flip-flops A(MSB) and B, one input variable X and one output function Y. For the circuit above: what is DA input equation? a)A+B b)A`BX` c)A+BX d)BX+ AX` e)A+B`X`
Flip flop input and output equations for a sequential circuit with 2 flip flops (A and B), 1 input (X) and 1 output (Z) are as follows. Create a state table for the circuit and draw the state diagram of the circuit. Write whether the circuit is a Mealy or Moore circuit and explain why. A(t+1) = A’X + BX' B(t+1) = AX’ + B'X Z = A’B'X'
Designing Sequential circuit Design a counter circuit which counts from 0-3. The counter stops at count 3 and will never go back to the count of 0. Use JK Flip-Flop. Show the transition table
You are givven a circuit consisting of one primary input, m, and one primary output, n. It incorporates two D flip-flops with inputs D2 and D0, along with corresponding flip-flop outputs Q2 and Q0. Additionally, there is a T flip-flop with input T1 and output Q1. The circuit is interconnected according to the following equations: D2 = m’Q2Q1 + mQ2’Q1 + m’Q2’Q1’Q0’ T1 = Q1’Q0‘ + mQ1’ + mQ2’Q0’ + m’Q2’Q0 + m’Q2Q1 D0 = m’Q2’ + m’Q1’Q0’ + m’Q1Q0 + mQ2Q1Q0’ n = Q2Q0 + mQ1’ + m’Q2’Q0’ Task: Perform state minimization by implication to reduce the number of states to a minimum. Which states are equivalent? In the minimized circuit, how many flip-flops are needed to implement the circuit?