Problem 2 A simply supported steel beam carries a factored concentrated load of 25 kips at the center of its 36-ft span. The beam has lateral support at the center of the span and at both ends (La- 18 ft). Use the AISC design graphs and the LRFD design method to select the most economical beam section. Neglect the beam weight. Design for bending only. The steel is A992, Grade 50. Sketch the design graph solution.

Problem 2 A simply supported steel beam carries a factored concentrated load of 25 kips at the center of its 36-ft span. The beam has lateral support at the center of the span and at both ends (La- 18 ft). Use the AISC design graphs and the LRFD design method to select the most economical beam section. Neglect the beam weight. Design for bending only. The steel is A992, Grade 50. Sketch the design graph solution.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

M1AQ99. For a loaded propped beam in the figure below, design a singly reinforced beam (using the USD method and NSCP 2015) for the positive moment. Give the complete details of the design. The total depth of the beam must not exceed 600 mm to ensure acceptable floor-to-floor vertical clearance. f'c = 28 MPa and fy = 415.7 MPa. It carries a super- imposed dead load of 90 kN/m and a live load of 38.4 kN/m all applied over the entire length of the beam. Other load and beam properties are the following: L1 = 6.3 m, L2 = 2.1 m, I2 = 0.65 of I1. Use a minimum concrete cover of 60 mm. Optimize the design such that the minimum percent difference of the moment strength with the actual moment is 1% but to avoid overdesign it's max percent difference is 5%. Design the rectangular beam details to provide: width, total depth, effective depth, number and diameter of tension bars (for two layers, provide number of bars in the upper and lower layer and vertical clear spacing between the 2 layers),…
A simply supported beam with a span of 9.5 m has a uniformly distributed dead load (including the beam weight) of 35 kN/m and live load of 30 kN/m. Use fc’ = 31 MPa, fy = 420 MPa, n = 6.8, and bar diameter of 32 mm. Determine the moment capacity (kN m) of the section under WSD conditions SHOW COMPLETE SOLUTION. NEED ASAP. THANK YOU.
Topic : Uncracked and cracked section 1. A beam has a width of 300mm and effective depth of 540mm, d’ = 60mm. It is reinforced with 4 – 25mm diam tension bars and 2 – 25mm compression bars. f'c = 28mpa and fy= 420. What is the ultimate moment capacity of the beam?
A 35-feed simply-supported floor beam, made of ASTM A572 Gr.50 (Fy = 50 ksi) W18x50 hot-rolled section bent about its major axis. is to carry a superimposed uniform dead load of 0.45 kip/ft and uniform live load of 0.75 kip/ft throughout its entire span. The beam is braced against lateral deflection at its supports and at its midspan. Assess the adequacy of the beam to carry the given loads. Use IBC limits for satisfying deflection requirements. Use LFRD specifications.
(30) Steel beam are centered 6’ apart. They support roof self-weight 20psf, snow 12psf, roof live load 18psf, upward wind 38psf or downwards wind 16psf. Determined factor LRFD uniformly distributed load per foot to be used for beam design. What would be design load if ASD method is used.
A steel I-beam UB 4 0 6 x 1 7 8 x 7 4 of grade S355 (Fig. 2) has two symmetrical concentrated loads applied in such a way that lateral deflection and twist are prevented at loading location and the end connections condition are as shown in Fig. 2. Determine its design load capacity if the span length is 12m.
Q9.7. A W24x176 of A572 grade 60 steel is used for a single span of 36 feet. If the only dead load present is the self weight of the beam, what is the largest concentrated service live load that can be placed in the center of the span? Assume continuous lateral support. It is not necessary to check the deflection. Use LRFD method
Engineer X decided to design a simply supported beam which carries a superimposed dead load of 12 kN/m in addition to its weight and live load of 47 kN/m. If the span is 9.0 meters, select the lightest W section that can carry the given loading. Assume that the beam has continuous lateral support and live load deflection may not exceed L/360. Use Fy = 450 MPa.
A 16-foot-long single overhang beam is loaded as shown. Assuming a W8 x 35 determine the maximum bending stress developed. The informally distributed load of 3 k/ft include the weight of the beam. Given: A992 steel Fb = 30 ksi.For W8 x 35 section properties see Table A3 (Textbook Appendix) (Provided)
PLease answer asap. will rate immediately. Thank you! a 4 m long simple beam is carrying a total dead load of 35 kN/m and a superimposed live load of 55 kN/m both uniformly distributed on the entire span. Regarding its details, it has 2-Ö20mm main bars at top and 3 – Ö20mm main bars at bottom. The beam is 250mm wide and 500mm deep. The concrete cover is 40 mm from the extreme fibers and two-legged 10 mm diameter bars for shear reinforcement. The beam is considered adequate against vertical shear. Given that f’c= 27.60 MPa and fy= 420 MPa.Determine the nominal shear carried by the concrete section using simplified calculation in kN.
A simply supported beam with an overhang span is subjected to a superimposed dead load (self-weight excluded) = 1.5 kips/ft and a live load = 2.5 kips/ft. Use a rectangular section for the beam to determine the width and height of the beam and design reinforcement for the beam per ACI318-19. 1. Draw moment and shear diagrams of the beam under factored load per LRFD given span length of 14ft
For a simply supported beam with span 5.5 m , determine the area of steel required to reinforced the beam(250*500) mm if it subjected to service dead load (including to self-weight) (15.3 kN/m) and service live load (36 kN/m) use f’c = 27.5??? & fy 414MPa