Problem 2: The device shown in the figure is known as a venturi. In this specific venturi, the differential pressure between locations 1 and 2 is 5 psi and the diameter ratio is D2/D1 = 0.35. If D2 = 8 inches, find the air flow rate through the frictionless venturi. 2)

Problem 2: The device shown in the figure is known as a venturi. In this specific venturi, the differential pressure between locations 1 and 2 is 5 psi and the diameter ratio is D2/D1 = 0.35. If D2 = 8 inches, find the air flow rate through the frictionless venturi. 2)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: The device shown in the figure is known as a venturi. In this specific venturi, the differential…

A: Given: The differential pressure between locations 1 and 2 is, P1-P2=5 psi. The diameter ratio is,…

Q: Oil is flowing at 0.015 m^3/s in the system shown below. Oil Specific Weight = 8.80 kN/m^3 Oil…

A: Given data: Here, Q represents the flow rate, w represents the specific weight, ν represents the…

Q: A 9.8 m A fluid of relative density 0.88 is flowing through a pipe constant diameter of 15 mm (see…

A: Fluid relative density = 0.88 PA = 150 KPa PB = 225 KPa ZA = 9.8 m ZB = 0 m

Q: A 2-inch copper pipe connection was made from the basement to the second floor in the building. The…

Q: An orifice of diameter 200 mm is fitted at the bottom of a boiler drum of length 6 m and diameter of…

Q: find the diameter of pipe of length 2500m when rate of flow of water through pipe is 0.25m cube/sec…

A: Given data: The length of the pipe is; L = 2500 m. The rate of flow through the pipe is; Q = 0.25…

Q: Q5:- Calculate the discharge of the system in fig. (4),neglecting all losses except through the…

Q: A venturi meter is introduced in a 300 mm diameter horizontal pipeline carrying a liquid under a…

Q: A 300mm * 150 mm venturimeter is inserted in a vertical pipe carrying water flowing in upward…

Q: The pressure tap for p2 is 0.457 m above the tap for p1

A: Given that, (a) Calculation for pressure at section 2: Since there is variation in diameter between…

Q: Find the flow rate that occurs in m3/h. Take π = 22/7. Determine the Reynolds number of this flow.…

Q: Water flows through the setup shown in the figure below. The diameter of the pipe is 80 mm. The…

Q: Find the diameter of a pipe of length 6 km when rate of flow of water through the pipe is 250…

A: Find the diameter of pipe using chezy's formula.

Q: Figure below shows a siphon that is used to draw water from a tank. The siphon tube has an inside…

Q: (b) A venturi meter with diameter at inlet D, and throat diameter D2, is used for measuring the flow…

Q: In the figure below, the losses up to section A is 5V,2/2g and the nozzle losses are 0.05V," /2g…

A: Given data as per question Height H =8 m D1 =150 mm D2 =50 mm calculations Water is incompressible…

Q: The water is flowing through a pipe having diameters 40 cm and 15 cm at sections 1and 2…

Q: 3: Calculate the pressure and velocity at points 2 and 3 for the water pipe shown in Figure D, = 14…

Q: 3 whot is the pressure in a 9.7-in bore horizontal pipe, :f the bore of the pipe norrows to 4.1 in…

A: Fluid Pressure Fluid Pressure is the pressure at point in the fluid arising due to weight of fluid.…

Q: The water is flowing through a pipe having diameter of 185mm and 142 mm at section (1) and (2)…

A: Given Data The flow rate is: c=56 L/sec=56×10-3 m3/sec The diameter of pipe at section (1) is:…

Q: Ex. 2.1] A pump delivering 230 Ips of water whose absolute viscosity 300-mm diameter suction pipe…

A: Fluid is a state of matter which deforms continuously on the application of the external force,…

Q: 2-the discharge through the pipe shown in fig. below is 0.4m'sec and the pressure head for point A…

Q: The water is flowing through a pipe having diameters 40 cm and 15 cm at sections 1and 2…

A: It is required to determine velocity head at inlet and outlet

Q: The device shown in the figure is known as a venturi. In this specific venture, the differential…

Q: (1) the diameter at the smaller end in meter (ii) the diameter at the larger end in meter (1 (ii)…

A: In this problem there are two separate independent questions. So I have solved the three part of…

Q: There is an upward flow from the vertical pipe shown in the figure. If the flow rate is 0.05 m3 / s,…

A: Given data: The flow rate is, Q̇ = 0.05 m3/s. Write the expression to calculate the velocity at…

Q: As shown in the Video and in the figure below, water "bubbles up" 9 in. above the exit of the…

Q: Find the pressure head at entry of the pipe, when the pressure of flowing fluid is 125 N/cm2 The…

Q: pipe with 20 mm diameter as shown in Figure Q3. If the pressure at point 1 is P1 kPa. Determine the…

A: since P1 value is not given then assume that P1= gauge pressure at point 1 in kpa. Take density of…

Q: A pump is used that has a Power Pb= 40HP and works with an efficiency of 85% to drive a flow rate Q…

Q: The device shown in the fugure below is known as a venturi. In theis specific venturi the…

A: Given:P1-P2=5psiD2D1=0.35D2=8in=812fthere,P1 and P2=Pressure at section 1 and 2 of venturiD1 and…

Q: Calculate the flow rate of the system by accepting the fluid passing through the reservoir-pipe…

Q: Friction in pipe cause O 1. reduction in potential energy 2. Reduction in velocity 3. Reduction in…

A: Friction loss in pipe is the Major loss.

Q: specific gravity of 0.80 and a viscosity of 27 [p] is transported at 200 [m^3/h] using a 10"…

Q: A fluid is pumped at a rate of 0.00156 m/s through a 0.025-m-diameter pipe to fill.a water tank as…

A: Given Data The discharge is:Q=0.00156 m3/s The diameter of the pipe is:d=0.025 m The density of the…

Q: The hydrostatic transmission shown in the figure, is used to move a pulley attached to the shaft of…

A: Write the given data

Q: Figure 5 shows a pump connected to a large tank of water. Water flows out of the tank through the…

A: Given:

Q: If you have a closed system that is filled with water on 2bar, the pump is selected for pressure…

A: 1) As it is a closed system, and the water inside the system is considered to be in static form…

Q: a venturimeter with inlet and throat diameters 300 mm and 150 mm respectively is attached in a…

A: Given, Inlet diameter d1 = 300 mm = 0.3 m Throat diameter d2 = 150 mm = 0.15 m Mercury difference in…

Q: l between the fluids in the U - tube arms is (x +) in em, where S.N. is student serial number.…

Q: The pressure through a section of pipe is 23 PSI and the velocity of the fluid is 3 ft/sec. If the…

Q: Q4) The three water-filled tanks shown in Figure below are connected by pipes as indicated. If minor…

Q: Two tanks A and B are connected by a pipe 30 m long. The first 21 m has a diameter of 75 mm and…

A: Given data as per question The total length of the pipe =30 m diameter of first 21 m length =75 mm…

Q: Problem 3: Gasoline 1sg = 0.0672 is flowing at 0.11 m³/s in the fabricated tube shown in the figure…

A: Given: The specific gravity of the gasoline, sg = 0.0672 The flow rate of the gasoline, Q = 0.11…

Q: Find the pressure head at entry of the pipe, when the pressure of flowing fluid is 175 N/cm2 The…

Q: Design the chilled water pipes system shown in the figure below and find the power of the pump…

Q: Q4: Answer A or B A-Ethyl alcohol flows in the pipe as shown in Figure below of specific weight 49…

A: Given dataEthyl glycol of specific weight w= 49lb/ft3Specific weight of mercury wHg = 846…

Q: QUESTION 3 Some hydraulic machines are served with water under pressure by a pipe 300 m long, the…

Q: Fluid flowing horizontally at 100gpm from a 2-in-diameter pipe to a 1-in-diameter pipe as shown in…

Question

Problem 2:
The device shown in the figure is known as a venturi. In this specific venturi, the differential
pressure between locations 1 and 2 is 5 psi and the diameter ratio is D2/D1 = 0.35. If D2 = 8 inches,
find the air flow rate through the frictionless venturi.
(2)

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1 Given data

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The water flows to the nozzle through a 180-degree elbow. The pipe diameter D-75mm, the nozzle diameter d=25mm, and the pressure gauge at the front of the pipe reads 60kPa. Find the force of the upper, middle and lower bolts at the flange joint 1-1 position. Assuming that four bolts are installed at the up, down, front and back, the cross-center distance of the four bolts is 150mm, the weight of the elbow and the water is 100N, and the acting position is shown in the figure. Please use conservation of momentum (momentum equation) and draw the control volume since that is our lesson.
The impact force exerted by water on the reduction element (spacer for reducing the pipe diameter) shown in the figure is F=400 and its direction is on the pipe axis and its direction is shown in the figure. Since the flow rate flowing from the reduction element is Q=18 lt/sec; Determine the pressure values in sections (1) and (2). D1=275 mm, D2=175 mm, γ mercury=13.6 t/m3. Friction and gravity forces will be neglected.(P1=?,P2=?)
Water flows through a circular pipe with a 180° elbow and exits to the atmosphere through a nozzle as shown in the figure. The diameter of the pipe is 300mm and the diameter of the nozzle exit is 160mm. The density of water is 1000kg/m3. The pressure gauge at the front of the pipe (section 1) reads 60kPa. Find the force of the upper, middle and lower bolts at the flange joint at section 1 position. Assuming that four bolts are installed at the up, down, front and back, the cross-center distance of the four bolts is 150mm and the weight of the elbow and the water is 100N. Z1 is 0.3 m.
The water flows from the nozzle through a 180-degree elbow. For example, the pipe diameter D-75mm, the nozzle diameter d=25mm, and the pressure gauge at the front of the pipe reads 60kPa. Find the force of the upper, middle and lower bolts at the flange joint 1-1 position. Assuming that four bolts are installed at the up, down, front and back, the cross-center distance of the four bolts is 150mm, the weight of the elbow and the water is 100N, and the acting position is shown in the figure.
The head-discharge characteristic relationship of a pump is given by:H = 40 - 200*Q^2, where H is the total head generated by the pump in meters and Q is the discharge in m^3/s. The pump lifts water through a pipe 0.3 meter diameter over a distance of 1000 meters against a static lift of 25 meters. Find the operating/ duty point (H and Q) if the friction coefficient of the pipe 'f ' is 0.03.
At point A where the diameter at of the pipe is 18 cm the pressure reading is 22.5 cm of Mercury. At point B, 3 m lower than A, the diameter is 48 cm and the pressure reading is 50 cm of Mercury. If the total head loss between the two points is 1.50 m, solve for the discharge. Water is flowing through the pipe. subject: hydraulics
The power 395 W is required to transmit 5 x 10-3 m3/s of water. Find the loss of head due to friction in a pipe. The head loss due to friction (in m of water) Answer
Q4: Answer A or B A-Ethyl alcohol flows in the pipe as shown in Figure below of specific weight 49 lb/ft3. What is the mass flow rate? If viscous effects are neglected. Take the specific weight for the mercury equal to 846 and for water equal to 62.4 at 68 0F.
Three hundred and eighty five gallons of water per minute is flowing through a 4.3-in radius horizontal pipe. If the bore of the pipe is reduced to 2.7-in radius and the pressure in the smaller pipe is 93 psig, what is the pressure in the larger section of the pipe? Include schematic diagram.
Write legibly 6. The piping shown in the figure is a parallel-pipe system carrying water at normal temperature. Pressure head at junction X is 76 m, while that at Y is 48 m. If the inflow at junction X is 0.35 cum/s, determine the flow of water at each branch of the loop. Assume C = 120 for all pipes. determine: a. flow in pipe A: ____________m3/s 1b. flow in pipe B: ____________ m3/s c. flow in pipe C: _____________ m3/s
1. The figure shows a type of flushometer in which the flat vane rotates on a pivot as it deflects the fluid stream. The fluid force is balanced by means of a spring. Determine the spring force required to hold the paddle in a vertical position when water is flowing at 100 gal/min. The diameter of the pipe is 1"
From a very large tank with an absolute pressure of 3 bar, the water is discharged to the atmosphere by means of 2 smooth pipes of 100 m length, 1 m and 50 m long, connected in series. The height difference between the water level in the tank and the outlet is 50m, and the diameters of the pipes are 50mm and 100mm, respectively. In addition, a 500kPa turbine is placed on the 2nd Pipe. a) Draw the system roughly, show the dimensions on it.b) Calculate the exit velocity of the water from the 2nd pipe, ignoring the local losses.