Problem 3- For the following section, determinea) Shear flow at A, B and Cb) If at points A and B we use nails with s = 150 mm, determine the shearforce in each nail.10 mm30 mm10 mm100 mm100 mm150 mm10 mm10 mm150 mm10 mm 125 mm10 mm

The figure of section is shown below. The area of the section is calculated as,

Answered: Problem 3- For the following section,…

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The beam is to be cut lengthwise along both sides, as shown in the figure. Nap made of a material that has an allowable shear stress of tperm = 75 MPa, determine the shear force maximum allowable V that can be applied before and after making the cut.
The box beam in the figure is made of four pieces of wood nailed to each other as shown.Since the distance between the nails is 32 and the allowable cutting force on each nail is 160, (a=16, b=38, c=32, d=190, F=160) a) Maximum allowable vertical shear force in the beam? b) Determine the corresponding maximum shear stress in the beam.
In the built-up box beam shown below, if a vertical shear force is applied, what value of Q, the first moment of area, should be used in determining the shear stress and/or shear flow at point A? Give your answer in m3m3.
Consider the beam shown in (Figure 1). Suppose that M = 9 kip⋅ft, P = 6 kip, w = 1.2 kip/ft, and point D is located just to the left of the 6-kip load. Follow the sign convention. Part A Part complete Determine the internal normal force at section passing through point D. Express your answer to three significant figures and include the appropriate units. Part B Determine the internal shear force at section passing through point D. Express your answer to three significant figures and include the appropriate units. Part C Determine the internal moment at section passing through point D. Express your answer to three significant figures and include the appropriate units. Part D Part complete Determine the internal normal force at section passing through point E. Express your answer to three significant figures and include the appropriate units. Part E Determine the internal shear force at section passing through point E. Express your answer to…
Calculate the vertical shear stress (N / cm2) at point A in the critical section of the beam below whose load and section is given? The cross section is symmetrical with respect to the y-axis. (Point A is on the body, point B is on the x-axis and point C is on the header.) (Q = 6000 N / m, P = 60000 N, L = 3 m, b = 50 cm t = 5 cm, h = 20 cm) please fast help please
Estimate the shear strain yxy at point D with respect to the xx and yy directions. A rectangle ABCD has width 400 mm (in the x-direction) and height 300 mm (in the y-direction). It deforms into the shape in the dashed lines. Point A (lowe right corner) moves to the right by 3 mm and upward by 2 mm, point B (upper right corner) moves to the right by 5 mm and upward by 4 mm, point C (upper left corner) moves to the right by 2 mm and upward by 2 mm.
Consider the beam shown in (Figure 1). Suppose that M= 9 kip⋅ft, P= 6 kip, w = 1.2 kip/ft, and point D is located just to the left of the 6-kip load. Follow the sign convention. Part D Part complete Determine the internal normal force at section passing through point E. Express your answer to three significant figures and include the appropriate units. Part E Determine the internal shear force at section passing through point E. Express your answer to three significant figures and include the appropriate units. Part F Determine the internal moment at section passing through point E. Express your answer to three significant figures and include the appropriate units.
vi) Using Macauley’s method, determine the deflection of the member at the locations where the 25 kN, 20 kN and 50 kN point loads are applied. Comment on how the maximum deflection of the member could be determined. Young’s Modulus of elasticity = 205 GN/m2Poisson’s ratio = 0.31
Determine the maximum normal stress and the maximum shear stress, making the graph of the corresponding diagrams. Also determine the diagram of tangential efforts.
What is the internal force in member AD? A. 750 N , T B. 450 N , T C. 750 N , C D. 450 N , C SHOW SOLUTIONS
The steel rod is stress-free before the axial loads P1 1⁄4 150 kN and P2 1⁄4 90 kN are applied to the rod. Assuming that the walls are rigid, calculate the axial force in each segment after the loads are applied. Use E 1⁄4 200 GPa.
A hydraulic punch press is used to punch a slot in a 0.60-in.-thick plate, as illustrated in the figure. If the plate shears at a stress of 39 ksi, determine the minimum force P (in kips rounded to the nearest tenths) required to punch the slot. Assume d = 0.75 in. and a = 4.00 in.

SEE MORE QUESTIONS

Recommended textbooks for you

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Fundamentals of Structural Analysis

Civil Engineering

ISBN:

9780073398006

Author:

Kenneth M. Leet Emeritus, Chia-Ming Uang, Joel Lanning

Publisher:

McGraw-Hill Education

Sustainable Energy

Civil Engineering

ISBN:

9781337551663

Author:

DUNLAP, Richard A.

Publisher:

Cengage,

Traffic and Highway Engineering

Civil Engineering

ISBN:

9781305156241

Author:

Garber, Nicholas J.

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS

Problem 3- For the following section, determine a) Shear flow at A, B and C b) If at points A and B we use nails with s = 150 mm, determine the shear force in each nail. 10 mm 30 mm 10 mm 100 mm 100 mm 150 mm 10 mm 10 mm 150 mm 10 mm 125 mm 10 mm