Procedure. IODOFORM TEST 1. Put 10 drops of the following compounds into separate test tubes: ethyl alcohol, propyl alcohol, isopropyl alcohol, phenol. 2. Add 20 drops of I2—KI solution to each tube and mix thoroughly. 3. To each test tube, add 5 drops of 10% NaOH solution. Mix well. Observe for any color changes or precipitation. 4. Record your observation in the data sheet. Question: Write the balanced equations for all the organic substances in the procedure.

Procedure. IODOFORM TEST 1. Put 10 drops of the following compounds into separate test tubes: ethyl alcohol, propyl alcohol, isopropyl alcohol, phenol. 2. Add 20 drops of I2—KI solution to each tube and mix thoroughly. 3. To each test tube, add 5 drops of 10% NaOH solution. Mix well. Observe for any color changes or precipitation. 4. Record your observation in the data sheet. Question: Write the balanced equations for all the organic substances in the procedure.

EBK A SMALL SCALE APPROACH TO ORGANIC L

4th Edition

ISBN:9781305446021

Author:Lampman

Publisher:Lampman

Chapter80: Crystallization: Purification Of Solids

Section: Chapter Questions

Problem 4P

See similar textbooks

Similar questions

you weigh your crude sample (1.538 g) and recrystallize with hot isopropanol. How do you know how much isopropanol to add?
To which sample solution the spike will be add? the distillate>130C the mass standard the distilled <130C
pls show detailed explanation and solution pls
Anion Test - Iodide (I-) Procedure : Dilute 6 drops of I- solution (NaI 0.5 M) by 12 drops of distilled water. Add HNO3 acid 4 M until the solution becomes acidic and add 2 drops of 4 M HNO3 for excess. Mix the solution with 1 mL of Fe(NO3)3 as well as 10 drops of dichloromethane and shake it. Results : After mixing the solution with Fe(NO3)3 , the solution turns dark yellow with almost brown. After adding the DCM, solution still remains dark yellow. What is the Chemical equation involved and Discuss the Iodide test?
this is the question from Organic Chem I "Separation of a mixture by acid-base extraction" Lab ps.please do not answer this question if you are going to type " I need more information" or didn't answer to this question
Read the detailed procedure of an experiment in your screen. Evaluate each step in the procedure whether it belongs to HOMOGENIZATION, EXTRACTION, PURIFICATION/CONCENTRATION, DATA TREATMENT, or INSTRUMENTAL ANALYSIS step.
step 1: Prepare a 1:15 soy flour-water mixture by adding l g soy flour to 15 ml distilled water in a 50-ml Falcon tube and vortex it to form a uniform suspension; pH 3.5 4.5 5.5 6.5 7.5 8.5 Dilution Factor 5 5 5 50 50 50 Absorbance 0.098 0.027 0.068 0.028 0.032 0.054 Concentration in diluted supernatant (mg/ml) 0.196 0.054 0.136 0.0056 0.0064 0.0108 Concentration in undiluted supernatant (mg/ml) 0.98 0.27 0.68 0.28 0.32 0.54 Calculate the amount (in grams) of soluble protein in the soy flour extract **Make sure to account for the dilution you made in Step 1 (Assume the volume of acid or base used to adjust the pH is negligible). Soluble protein (g) = (C x V x F) / 1000 C = concentration (mg/ml); F = dilution factor; V = volume of solution (ml)
Experiment 2 - Extraction Procedure The procedure[1] has been outlined below. Add details if needed so that you are able to complete the experiment in lab using only this document. The following chemicals may be encountered during this experiment: Acetylsalicylic acid Sucrose Acetanilide Ethyl acetate Sodium bicarbonate (NaHCO3) Hydrochloric acid (HCl) Sodium sulfate (anhydrous) Dissolve phensuprin (0.5 g) in ethyl acetate (25 mL). Measure out 0.5-1.0 g of phensuprin and put it in a beaker (100 mL) along with 25 mL of ethyl acetate. Stir for 1-3 min, breaking up any chunks as needed Sucrose will not dissolve, but everything else will. Gravity filter the solution to collect the sucrose. Set up a glass funnel in a ring or clamp, so that it will drain into a clean Erlenmeyer flask (125 mL). Put a fluted filter paper into the funnel and "wet" it with ethyl acetate. Optional: Weigh the filter paper before using it. Swirl and pour the solution into the funnel, being…
Can someone please check this for me and explain
What does it mean if the color of the solution in UV flashlight are the following Sample 1- light green Sample 2-light green Sample 3- sky blue Sample 4-- blue green Sample 5--cyan blue green Sample 6-- light green
L.5 Hi Experts! Can you please help me complete the tables? please kindly also include some sample calculations. THANK YOUUU SOO MUCHH!! Results (GIVEN) Solvent Trial Volume of NaOH (mL) Concentration of NaOH (M) Volume of Solution (mL) Concentration of Solution (M) Water 1 15.6 0.4664 10 2 15.4 0.4664 10 Average Ether 1 31.9 0.0823 10 2 31.8 0.0823 10 Average Table 1. Data for 1 M Acetic acid. Solvent Trial Volume of NaOH (mL) Concentration of NaOH (M) Volume of Solution (mL) Concentration of Solution (M) Water 1 7.6 0.4664 10 2 7.7 0.4664 10 Average Ether 1 20.2 0.0823 10 2 18.3 0.0851 10 Average Table 2. Data for 0.5 M Acetic acid. Solvent Trial Volume of NaOH (mL) Concentration of NaOH (M) Volume of Solution (mL)…
Explain and elaborate. Show solution and sketch if possible. No plagiarism.