Q-5) In a three-layered soil system, the thicknesses of the top and bottom layers each are half the thickness of the middle layer. The coefficients of permeability of the top and bottom layers each are double the coefficient of permeability k of the middle layer. When horizontal flow occurs, the equivalent coefficient of permeability of the system will be.

Q-5) In a three-layered soil system, the thicknesses of the top and bottom layers each are half the thickness of the middle layer. The coefficients of permeability of the top and bottom layers each are double the coefficient of permeability k of the middle layer. When horizontal flow occurs, the equivalent coefficient of permeability of the system will be.

Fundamentals of Geotechnical Engineering (MindTap Course List)

5th Edition

ISBN:9781305635180

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter11: Ground Improvement

Section: Chapter Questions

Problem 11.9P

See similar textbooks

Similar questions

A soil profile consists of 2m of sand (γ=18kN/m³, kv=4 x 10-2m/day) over 3m of silt (γ=17kN/m³, kv=1 x 10-2m/day) over 2m of silt (γ=16kN/m³, kv=5 x 10-4m/day) over gravel. The water table is 0.5m below the ground surface. A piezometer placed at the top of the gravel layer measures a porewater pressure of 42kPa. Assuming a one-dimensional flow condition in the vertical direction, compute the flow rate in m³/day/m². Also compute, atmiddepth of the clay layer, the porewater pressure, total vertical stress, and effective vertical stress.
A permeable soil layer is underlain by an impervious layer as shown. For permeable layer K=4.8x10-3 cm/sec. If H = 3 m and α = 5˚ (See picture below) Determine the hydraulic gradient Determine the cross-sectional area of the permeable soil layer. Determine the rate of seepage in cm3/hr/meter.
A layer soil has the following data: H1=3m K1=2x10^-2 cm/sH2=4m K2=3.2x10^-2 cm/sH3=6m K3=4.1x10^-2 cm/s a) Compute the equivalent coefficient of permeability in the vertical directionb) Compute the velocity of flow if h =4 m.
A dense silt layer has the following properties: e=0.30, D10=10µm and capillary constant = 0.20cm2 Free ground water level is 8m below the ground surface. Determine the vertical effective stress (kPa) at 5m depth (point A). Assume unit weight of solids = 26.5 KN/m3 and that the soil above the capillary rise and ground surface is partially saturated at 50%.
A dense silt layer has the following properties: void ratio e = 0.50, effective Diameter D10 = 10 μm, capillary constant C = 0.20 cm2. The free groundwater level is 8m below the ground surface. Assume unit weight of solids y= 26.50kN/m3. Find the vertical effective stress at 10m depth. Assume that the soil above the capillary zone is partially saturated at 50%.
A dense silt layer has the following properties: void ratio = 0.7, specific gravity = 2.58. Free ground water is 10.58 m. below the ground. Capillary action rise will reach 7.46 meters. The soil above capilary action rise is dry while within the zone, it is saturated at 54.74 %. Determine the effective pressure (in kPa) at a depth of 7.5 meters from the ground surface.
A uniform soil deposit has a void ratio 0.6 and specific gravity of 2.65. The natural ground water is at 2.5 m below natural ground level. Due to capillary moisture, the average degree of saturation above ground water table is 50%. Determine effective pressure in kPa at a depth of 6 m. a. 46.40 b. 323.9 c. 80.66 d. 117.9
The sand layer shown is 2.5m thick. Beneath the sand layer is a 1.8m thick clay layer, underneath the clay layer is a solid rock. Water table is at depth of 0.9 m below the ground surface. SAND: Ymoist= 23KN/m3 ; Ysat= 21KN/m3 CLAY: Ysat= 23 KN/m3 ; LL= 42% e=0.7 A.) Compute the overburden pressure at mid-clay layer. B.) Find the maximum surface pressure without exceeding a 139.5mm settlement in clay layer if it is assumed to be normally consolidated. C.) If surface pressure is 70kpa and pre-consolidation pressure is 80kpa, find the settlement in clay layer.
29. Soil in a field has three layers. Each has a thickness of 3m, 4m, and 3m, from top layer to bottom layer. The hydraulic conductivity of each layer is 0.0043cm/s, 0.0072cm/s, and 0.0018cm/s, respectively. Calculate the effective horizontal hydraulic conductivity.
A dense silt layer has the following properties: void ratio = 0.67, specific gravity = 2.55. Free ground water is 10.96 m. below the ground. Capillary action rise will reach 5.81 meters. The soil above capilary action rise is dry while within the zone, it is saturated at 51.78%. Determine the effective pressure (in kPa) at a depth of 7.21 meters from the ground surface. Round off to three decimal places.
seepage is occurring through the sandy layer underneath the concrete dam.Given: upstream water level = 15.8 m; downstream water level = 2.1 m; thickness of the sandy layer = 1.1 m; coefficient of permeability of the sandy layer = 0.0081 cm/s and L = 48 m. Determine: 1.The seepage flowrate per unit length of the wall in m3/hr/m. 2.Quantity of seepage per day if the dam is 400 m long.
A dense silt has the following properties: void ratio = 0.64, specific gravity = 2.5. Free ground water = 10.23m below the ground. Capillary action rise will reach 5.6m. The soil above the capillary action rise is dry while within the zone, it is saturated at 51.53%. Determine the effective pressure (in kPa) at a depth of 7.42m from the ground surface.