Q.3) Determine the support reactions at A and B of the bent bar AB shown below. The collar at B can glide freely along the cylindrical rod CD and is fixed to the bar AB. 1900N 1 m -1 m- 45° 2 m В 800 N· m 45°

Q.3) Determine the support reactions at A and B of the bent bar AB shown below. The collar at B can glide freely along the cylindrical rod CD and is fixed to the bar AB. 1900N 1 m -1 m- 45° 2 m В 800 N· m 45°

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter10: Virtual Work And Potential Energy

Section: Chapter Questions

Problem 10.32P

See similar textbooks

Related questions

Q: If m = 30 kg and assuming rough surfaces, draw the free-body diagram. Cable A 0.1 m В 30°

A: Answer: tension in the cable = 169.914 NFor a step-by-step solution have a look through the…

Q: Problem 1.3 A telephone pole sits on a rough surface. A cable attached to an excavator is then used…

A: Dear student, According to the expert guidelines, I am allowed to answer only…

Q: Determine the reaction forces at the four contact points A, B, C and D. Small: Mass of 1.02 kg…

Q: P.1) The rigid rod of length L is free to rotate in a horizontal plane. A moment Mk is applied to…

A: As per given question The rigid rod of length L is free to rotate in a horizontal plane. A moment Mk…

Q: A fixed crane has a mass of 1000 kg and is used to lift a 2400 kg crate. It is held in place by a…

Q: The light right-angle boom which supports the 400-kg cylinder is supported by three cables and a…

A: Given Applied load = 400 kg To find Reaction at point O Cable tension

Q: ww os 240 mm

A: A vector is a physical quantity that has magnitude and direction both. A scalar is a physical…

Q: a sheep with a mass of 50 kg is hung on an animal scale system which consists of a helical spring of…

Q: Determine the largest force P (to the nearest integer) which can be applied to the cord without…

Q: A circular flap with a diameter d closes the outflow of water from a tank. The flap rotates around…

Q: A bucket which has a mass of 910g when empty and contains 3 litres of water is swung round in a…

A: When a body rotates in a circle it experiences a outward force called centripetal force, which is…

Q: 2. If a wooden block of weight W = 9.7 N placed on a smooth surface inclined at an angle 35 and is…

A: The F will be equal to the reaction force act on the block F=R=mgcosα=Wcos35=9.7cos35≈7.9

Q: n and loading

A: given:

Q: 4/97 A 250-N force is applied to the foot-operated air pump. The return spring S exerts a 3-N m…

A: For the given arrangement To determine (i)Corresponding Compression force C in the cylinder BD…

Q: 1. A sphere loaded by its own gravitational force G=250 N is placed between two perfectly smooth…

Q: 2. The homogeneous disk shown is resting on an inclined friction surface. Determine the magnitude of…

Q: 3. A man is trying to pull the sled by applying a force of 500 N, as shown. The weight of the stone…

Q: B. 2. A cable goes over a frictionless pulley at B and supports a block of mass m. The other end of…

A: Given data: - The vertical distance between point A and B is h = 5 m. The horizontal distance…

Q: A rubber cord has a diameter of 5.0 mm, and an unstretched length of 1.0 m. One end of the cord is…

Q: Given problem: A cylinder having a mass of 268.6 kg is to be supported by the cord which wraps over…

A: Given data Mass of cylinder = 268.6 kgCoefficient of friction = 0.2We have to determine the maximum…

Q: In the assembly shown, sags of s and 1.5 s resultedwhen the two cylinders were suspended from the…

Q: The forces F1 = 500 N, F2 = 400 N, and F3 %3D = 700 N all of which act on point A of the bracket,…

A: Given: F1 = 500 NF2 = 400 NF3 = 700 N Angle which force F1 makes with the…

Q: Q/Determine Hhe x 2. and y Components of F, and Fz actig. the boom Shown in figue below - on

Q: Three identical steel balls, each of mass m=75kg, are placed in the cylindrical ring which rests on…

A: Solution- Given data- m =75kg

Q: The quadriceps tendon attaches to the tibia at a 30°angle 4 cm from the joint center at the knee.…

Q: The uniform bar is at rest on a smooth half-sphere with radius R = b / 2. In A there is a ball joint…

Q: For the crane system, determine the hydraulic cylinder force required to lift a 3500 N load O21349 N…

A: To Find The hydraulic cylinder force required to lift. FBD: The free body diagram.

Q: Q1) The quadriceps tendon attaches to the tibia at a 30° angle 4 cm from the joint center at the…

A: for the quadriceps attaches to the tibia according to the given information we have to solve for the…

Q: 50 kg Ма 3 ft - 3 ft- 200 lb · ft Collar 4 ft 3 13 ]5 12 Smooth surface В Fig 1

Q: Calculate the magnitude of the tension T and the angle e for which the eye bolt will be under a…

A: Forces are resolved in components in x and y directions and equated for the given conditions.…

Q: Determine the tensions in cables AC and AD. Tension TAB= 500 N. 1.25 m 1.5 m 1.25 m 1.0 m B D. 1.0…

Q: Your answer is partially correct. Calculate the force and moment reactions at the bolted base O of…

Q: Q (7): Determine the maximum mass of the flowerpot that can be supported without exceeding a cable…

A: Consider below FBD at point A: Given, max ( TAB , TAC ) = 90 N

Q: Q1) The quadriceps tendon attaches to the tibia at a 30° angle 4 cm from the joint center at the…

A: Given that the 80 N weight is attached to the ankle 0.28 m from the knee joint, Also, Fm is the…

Q: SITUATION 2: The truss has the following configuration where e is 45° 10 kN 15 kN B H The force at…

Q: Q1) The quadriceps tendon attaches to the tibia at a 30° angle 4 cm from the joint center at the…

Q: If a wooden block of weight W = 9.7 N placed on a smooth surface inclined at .2 an angle 35 and is…

Q: Q (7): Determine the maximum mass of the flowerpot that can be supported without exceeding a cable…

A: Given data: TAB = TAC = 70 N Need to determine the maximum mass of the flowerpot.

Q: The telescoping arm ABC of Prob. 6.93 can be lowered until end C is close to the ground, so that…

Q: The grey block D in the sketch has a mass of 100 kg. The blue wedges (B and C) have a mass of 10 kg.…

Q: Determine the tensions in cables AB, AC, and AD. 1.50 m 2.00 m B 1.50 m 0.80 m D 2.9 m AO 150 kg

A: Now write the position coordinate for each point.

Q: Two smooth cylinders, A (weighing 80 N. and having a diameter of 16 m.) and B (weighing 60 N and…

A: A free body diagram (also known as a force diagram or FBD) is a graphical representation of the…

Q: The horizontal steel shaft has a mass of 360 kg and is suspended by a vertical cable from A and by a…

Q: A fixed crane has a mass of 1000 kg and is used to lift a 2400 kg crate. It is held in place by a…

Q: An acrobat is walking on a tightrope of length L-20.1 m attached to supports A and B at a distance…

A: Given, Length of the rope is 20.1 m Distance between AB is 20 m Let, Length of lope AC=l Horizontal…

Q: Three identical steel balls, each of mass m=85kg, are placed in the cylindrical ring which rests on…

Q: For the figure shown below. Determine the force exerted on the bar ABC by the cylinder with a mass…

Q: Calculate the vertical reaction at J. 15 KN 10 KN 10 KN 20 KN A D 5.0m H. G 4 @ 3.0 m = 12.0 m O…

Q: The curve surface represented by AB in the figure is the surface of the quadrant of a circular…

Q: F -3 ft 3 ft- M 2 ft 13 B 12

Concept explainers

Forced undamped vibrations

In mechanical engineering, vibration is expressed as the term that occurs due to an object's backward and forward movement about a point of equilibrium. Generally, there are three types of vibrations which are,

Question

Q.3) Determine the support reactions at A and B of the bent bar AB shown below.
The collar at B can glide freely along the cylindrical rod CD and is fixed to the
bar AB.
A
1900N
1 m
-1 m-
45°
2 m
В
800 N· m
45°

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The bent rod is supported by a smooth surface at B and by a collar at A, which is fixed to the rod and is free to slide over the fixed inclined rod. Suppose that F = 170 lb and M = 350 lb⋅ft A) Determine the magnitude of the reaction force on the rod at B. NB = ? B) Determine the magnitude of the reaction force on the rod at A. NA= ? C) Determine the moment of reaction on the rod at A. MA= ?
The bent rod is supported as shown in the figure by a smooth surface at B and by a collar at A, which is fixed to the rod and is free to slide over the fixed inclined rod. Suppose that F = 120 lb and M = 400 lb⋅ft. a) Determine the magnitude of the reaction force on the rod at B. b) Determine the magnitude of the reaction force on the rod at A. c) Determine the moment of reaction on the rod at A.
PROBLEM 1: The 1500-kg beam ABC has fixed support at A and connected to beam BD by hinge at B. Beam BD has a mass of 2000 kg and supported by a cable at D. The cable is attached to the 20-cm-diameter pulley at E and pulled vertically at the other end, by tension T. Given: a = 1.5 m; b = 0.9 m; c = 1.8 m d = 0.6 m; e = 1.4 m; θ = 75°. Calculate the required tension to maintain in equilibrium. (ANSWER: 12.830KN) Calculate the moment reaction at A. (ANSWER: 28.499) Calculate the total reaction at A. (ANSWER: 22.192) Calculate the vertical reaction at E. (ANSWER: 25.223)
Determine the magnitude and direction of the angle theta of the force FAB that must be exerted on bar AB to maintain equilibrium of the system. The suspended mass is 110 kg. Neglect the size of the pulley at A and treat all pulleys as smooth. What should happen to maintain the equilibrium of the system if FAB acts with an angle theta= 0°?Consider g = 9.81 m/s2.
2-D PROBLEM: A spherical tank with a radius of 3.41m that has a mass of 28928.644kg was supported in the system shown. Assuming friction and the bar weight is negligible, determine the following: β: 21.774° θ: 46.452° 1. The reaction @ point D. 2. Tension @cable BE 3. The x and y-component of the reaction @ A 4. The reaction @ A
Given problem: A cylinder having a mass of 268.6 kg is to be supported by the cord which wraps over the pipe. If ?? = 0.2, determine the largest vertical force ‘F’ that can be applied to the cord without moving the cylinder. The cord passes: a) Once over the pipe, β = 180° b) Two times over the pipe, β = 540°
The hoist supports an engine of weight W in kg. Determine the force the load creates in member DB and in member FB, which contains the hydraulic cylinder H. Given: X=2 m ; L=3 m ; W= 123 kg.
Make the free body diagram and calculate the reaction efforts at the points with movement restrictions imposed. Data: L1 = 1.9m L2 = 3.3m L3 = 3.5m P1 = 75kN P2 = 140kN
Find the stable equilibrium position of the system described in Prob. 10.56 if m = 2.06 kg.
The bar AC is supported by a joint at A and a pin B that is free to slide in the same direction (alpha) of the bar. A bar is connected at C and a force is applied in the theta direction. Consider that L1 = 2.7 m, L2 = 1.7 m, alpha = 13 °, theta = 25 °, and P = 68 kN. Determine the magnitude of the force (kN) on pin B.
A cylinder having a mass of 100 kg is to be supported by the cord which wraps over the pipe. Determine the smallest vertical force F needed to support the load if the cord passes twice over the pipe, β = 540˚. Take μs = 0.2.
If the block remains in the equilibrium position shown, determine the mass of the block D. The unextended length of spring AB is 9 m. d1 = 8 m d2 = 10 m KAC = 44 N/m KAB = 70 N/m Mass of block D = ____ kg