Q3A mixed-model assembly line has eight stations. Average cycle time is 15 minutes, but times varydue to model type and natural randomness. The estimated standard deviation of processing time in astation is 4.5 minutes. Estimate the production rate for the asynchronous line if no buffer is allowed.

Answered: Image /qna-images/answer/4125427a-d2d0-4183-b594-f3f7f4b34a80.jpg

Answered: Q3 A mixed-model assembly line has…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Consider the basic EOQ model. We want to know the sensitivity of (1) the optimal order quantity, (2) the sum of the annual order cost and the annual holding cost (not including the annual purchase cost cD), and(3) the time between orders to various parameters of the problem. a. How do (1), (2), and (3) change if the setup cost K decreases by 10%? b. How do (1), (2), and (3) change if the annual demand doubles? c. How do (1), (2), and (3) change if the cost of capital increases by 10%? (For this part, assume that the storage cost s is zero.) d. How do (1), (2), and (3) change if the changes in parts a, b, and c all occur simultaneously?
A _____system uses measurements of disturbance variables to position the manipulated variable in such a way as to minimize any resulting deviation. The disturbance variables could be either measured loads or the set point, the former being more common.
Which is more important to you– model accuracy, or model performance?
Why random errors is unavoidable
An automotive V6 engine consists of six identical cylinders for the engine to perform its intended functions. All the six cylinders must be operationally successful and the mileage to failure of a cylinder can be modeled with the Weibull distribution with shape parameter 1.5 and characteristic life 3.5x106 miles.Calculate:(a)The reliability, R (t) of the engine. (b) The failure rate, h (t) of the engine. (c) With your expertise as a quality reliability engineer, how would you achieve a product life cycle in typical manufacturing industry?
Case 1: Material system without density and viscosity differences Though unlikely in real life, in this case, we assume that all of the material in the homogenizer is of the same density and viscosity. Thus, only one set of material parameters are mentioned (density, ρ; dynamic viscosity, μ). The important parameters are listed as follows: Target quantity : Mixing time, θ Geometric parameters : Stirrer diameter, d Material parameters : Density, ρ Dynamic viscosity, μ Process-related parameters : Stirrer speed, n 1.1) Write out the relevance list for Case 1. 1.2) Generate the pi-set for this case. 1.3) Write out the appropriate pi (π) numbers from the generated pi-set. 1.4) Identify the established dimensionless numbers from the derived pi (π) numbers. 1.5) Write the possible relationship of the dimensionless numbers for Case 1.
The sales of a product during the last four years were 860, 880, 870 and 890 units. The forecast for the fourth year was 876 units. If the forecast for the fifth year, using simple exponential smoothing, is equal to the forecast using a three period moving average, what is the value of the exponential smoothing constant?
Although the terms “model” and “prototype” are often used interchangeably, they are not the same thing, explain the difference
Discuss three typical advantages a physical prototype manufactured additively has over a virtual/analytical model when used within a Concurrent Engineering environment.
Statics and Rigid bodies: Can you please show me how to solve the following Sample Problem? in step by step solution Thank you so much!
A HSS tool is used to turn a steel workpart that is 300 mm long and 80 mm in diameter. The parameters in the Taylor equation are: n = 0.13 and C = 75 (m/min) for a feed of 0.4 mm/rev. The operator and machine tool rate = $30.00/hr, and the tooling cost per cutting edge = $4.00. It takes 2.0 min to load and unload the workpart and 3.50 min to change tools. Determine: Tutting speed for maximum production rate, Tool life in min of cutting, and Cycle time and cost per unit of product. determine cutting speed for minimum cost.
Pressure distribution measurements are made on a two-dimensional wing model placed in a wind tunnel. The difference between the static pressure sockets on the surface and the static pressure of the free stream is measured. 30 data is taken at each measurement point. The average of the values measured from one of the sockets near the trailing edge was calculated as 2.30 Pa, and the standard deviation was calculated as 2.65 Pa. After applying the Chauvenet criterion to these measurement values, it was decided to eliminate 3 measurements and the new mean value was found to be 2.18 Pa and the standard deviation was 2.42. It was verified that the unexcluded data fit the normal distribution curve. Data above how many Pa and below how many Pa were eliminated? Estimate how many data have negative value (?<0) after elimination.

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS