Subject Power System Analysis Q3)in p.uConsider 4-bus 5 line Power System shown below. All indicated values are admittancesY12 =2-j6Y13 =1-j3Y23 =0.666-j2Y24 =1-j3Y34 =2-j6y4 =j0.2:a.Develop the Y-bus matrix (i.e., the admittance matrix).

The bus admittance matrix elements can be calculated as: Y11 = Y12 + Y13 = 2 -j6 + 1 - j3 = 3 - j9…

Answered: Q3) Consider 4-bus 5 line Power System…

Q3) Consider 4-bus 5 line Power System shown below. All indicated values are admittances in p.u Y12 =2-j6 Y13 =1-j3 Y23 =0.666-j2 Y24 =1-j3 y34 =2-j6 Y4 =j0.2:

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter6: Power Flows

Section: Chapter Questions

Problem 6.2MCQ: For an NN square matrix A, in (N1) steps, the technique of Gauss elimination can transform into an...

See similar textbooks

Related questions

Q: 3.23 Figure 3.32 shows the oneline diagram of a three-phase power system. By selecting a common base…

A: Sketch the one-line diagram of a three-phase power system The data is given in the table Base…

Q: Question 5: A single-phase transmission line has a resistance of 0.22 ohm and inductive reactance of…

A: Given transmission line is single-phase transmission line. Resistance of the line, R=0.22Ω.…

Q: Q.22: 380V, 3-, 4-wire CBA system with A-connected load (3+j4,3-14,5) ohm. Find the line currents…

A: Delta Connections: In a three-phase electrical system, a delta connection is formed by three…

Q: 5. Let a(n) be a real-valued minimum-phase sequence. Modify r(n) I to obtain another real-valued…

A: x(n) is modified to obtain a real-valued minimum phase sequence

Q: Q.35: Three wattmeters W, W, W, are connected, respectively to phases a, b. and c to measure the…

A: Given unbalanced load ZAB=10-j5 ΩZBC=16 ΩZCA=8+j6 ΩSource voltage =440 v

Q: , The reactance data for the power system shown in Figure 10.30 in per unit on a common base is as…

Q: Figure shows a sample power system network and Zpus Matrix elements. For a solid three phase fault…

Q: 4. A balanced Y-connected 400V voltage source is where Z, = 20-j40 and Z2 = 3+ j45 Ohms a connected.…

A: In this question we will find source current in per unit....

Q: The national standard phase sequence in oman is R B Y Select one: True False

A: The national standard phase sequence in Oman is R B Y this statement is true.

Q: (2 12 Zload = 300 %3D K L M N 13.2 kV ZL = 10 + j100 %3D 5 MVA 10 MVA 13.2A - 132Y kV 138Y – 694 kV…

A: Given: Base MVA (SB)=50 MVA For transformer A: SA=5 MVAVoltage rating: 13.2(delta)-132(star)…

Q: (3 T2 Machine 1 Machine 2 Y A Two synchronous machines are connected through three-phase…

A: Given: Two synchronous machines are connected through three-phase transformers as shown in the…

Q: Estimate the requirement of materials and their I phase overhead Service Connection Cost for giving…

A: single phase service connection to building Length of service main =15 m Total load of installation…

Q: In a three – phase system with balanced loads, total power using one wattmeter method is given by -…

A: A circuit of power measurement using three wattmeter method is shown

Q: Figure 3.32 shows the one-line diagram of a three-phase power system. By selecting a common base of…

Q: Figure 1 shows the one-line diagram of four-bus power system with generation at bus 1 and bus 4. The…

A: Solution- The given figure is shown below,

Q: Q// For the two-bus power system shown in Fig.(PA) Slack bus (G1 V1= 1.0L0° pu Sg2 = 0.2 +j0.05 pu…

A: Answer -

Q: Figure 1 shows the one-line diagram of four-bus power system with generation at bus 1 and bus 4. The…

A: Solution- The given figure is shown below,

Q: For balanced three phase star connected load, the phase angle difference between VR and VY is 30…

A: Given statement For balanced three phase star connected load, the phase angle difference between VR…

Q: Draw a single line per-unit impedance diagram for the system whose single line di Figure 2. The…

Q: 1. In a 3-phase overhead system, each line is suspended by a string of 3 insulators. The voltage…

A: Given voltage across top and middle units, using this we will find Ratio of capacitance, string…

Q: For the system shown below with x=0.9 pu, determine static limit and corresponding voltage magnitude…

A: The system diagram is shown below, Where, x=0.9 pu

Q: Figure 1 shows a three-phase power system network comprises of synchronous generator, transformers,…

Q: In a 3-phase overhead system, each line is suspended by a string of 3 insulators. The voltage across…

Q: The 3-phase power and line-to-line voltage ratings of the electric power system shown in the…

A: In this question we need to find a impedance of the motor in per unit.

Q: Use the Y-Y circuit shown below, a)Solve for the phase voltage at load end b)Solve for the phase…

A: In this question we need a)Solve for the phase voltage at load end b)Solve for the phase current.

Q: The one-line diagram of a three-phase power system is as shown in the figure attached. Impedances…

A: The load at bus is S2=15.93 MW-j33.4 MvarFirst converting all the values in per-unit systemThe load…

Q: he one-line diagram of a three-phase system is shown in Figure 1. By selecting a common based of 100…

A: Given, Common base power, SB = 100 MVA Base voltage = 32.75 KV

Q: Q2. The one-line diagram of a simple power system is shown below. The load, to b impedance, draws 90…

A: The reactance diagram is shown. A base of 40 MVA and 13.8 kV in the generator side is chosen. The…

Q: For the system shown below with x=0.9 pu, determine static limit and corresponding voltage magnitude…

A: The power system has to transmit power from the generation side to the load side. For this purpose,…

Q: Write the node formulation for nodes with the passive element currents given in term of nodes…

Q: [j0.11565 j0.045807 Ljo.04580 j0.13893 between buses 1 and 2, what is the new Zpus? A two-bus system…

A: A power station is to provide electricity to a huge number of people. Different customer’s power…

Q: Q.13: 380V line voltage, 3-0. 3-wire A-connected, negative sequence (acb), power system with first…

A: “Since you have asked multiple question, we will solve the first question for you. If you want any…

Q: What do you understand by means of power system? A 3-q, 50 Hz transmission [ line is 120 km long. It…

Q: What are the types of connections in three phase load, which connection is best? Justify your…

A: Four types of connection we have for three phase transformer- Y-Y- This is used for small, H.V.…

Q: In single phase overhead transmission lines, the increase of the line resistance leads to an…

A: To solve the above problem one should have a clear understanding of phasor quantities: In a…

Q: A load flow analysis is to be performed on a four bus power system, the per unit admittance matrix…

A: Solution: (a) Non-diagonal elements, y12=-Y12=2-j6 y13=-Y13=1-j3…

Q: 1. The one-line diagram of a three-phase power system is shown in the following Figure. V3 j26.459…

A: Base MVA = MVAb =100 MVA

Q: consider the following diagram of impedances in per unit of a common base a) get the YBus admittance…

Q: The bus admittance matrix for the power system shown in Figure 1 is given by 3-j9 −2+j6 -1+j3 0 Ybus…

A: Gauss-Seidel (G-S) method is one of the simplest iterate method. It is a modification of…

Q: 15. phase is 120 V and 100 A, respectively, calculate a) In a three-phase transmission power system,…

Q: 1. Identify unity power factor points on V-curves and comment why you will not get unity power…

A: An alternator/synchronous generator is a type of electrical machine that converts mechanical energy…

Q: a) Explain mathematically how to covert impedance Z per unit using new MVA and kV bas values. b) A…

A: In this question we will write how we will convert impedance from old MVA and KV to new MVA and…

Q: (b) For a 4-bus 3-phase, 100 kV, 50 Hz power system, the following Y-bus and corresponding Z-bus…

Q: Q3) A balanced 3-phase load of 30 MW is supplied at 132 kV, 50 Hz and 0-85 p.f. lagging by means of…

Q: Given the circuit shown below, if Zx = 100<0degrees determine the current in each branch using NODAL…

A: NOTE: Unit of Zx is not given. we assumed it as ohm. We assumed nodes and current directions on the…

Q: 1. Maximum power transfer happened when! a. Z₁1-Zg b. Z₁-Zh c. ZL-Z22. 2. The voltage equations in…

A: 1) Maximum power transfer happen when.... ANSWER - ( b ) ZL=Zth* in a DC circuit, the load…

Q: A three-phase transmission line and a telephone line are supported on the same towers a shown in the…

A: Given, frequency = f= 60 Hz Current per phase= I = 200 A Da1=Dc2=42+3.6-0.62 =…

Q: A single phase transmission line is delivering 480 kVA load at 11 kV. Its resistance is 6 n and…

A: In this question, Single phase transmission line Load = 480kVA, at 0.9PF lagging. Find the…

Q: Figure 1 shows the one-line diagram of four-bus power system with generation at bus 1 and bus 4. The…

A: The given figure is shown below, Consider,Current and voltage at node 1 = I1, V1Current and voltage…

Concept explainers

Differential amplifier

There are two amplifying stages with common degeneration in a differential amplifier.

Question

Subject Power System Analysis

Q3)
in p.u
Consider 4-bus 5 line Power System shown below. All indicated values are admittances
Y12 =2-j6
Y13 =1-j3
Y23 =0.666-j2
Y24 =1-j3
Y34 =2-j6
y4 =j0.2:
a.
Develop the Y-bus matrix (i.e., the admittance matrix).

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A small manufacturing plant is located 2 km down a transmission line, which has a series reactance of 0.5/km. The line resistance is negligible. The line voltage at the plant is 4800V(rms). and the plant consumes 120kW at 0.85 power factor lagging. Determine the voltage and power factor at the sending end of the transmission line by using (a) a complex power approach and (b) a circuit analysis approach.
For an NN square matrix A, in (N1) steps, the technique of Gauss elimination can transform into an ____________ matrix.
Determine the bus admittance matrix (Ybus) for the three-phase power system shown in Figure 6.23 with input data given in Table 6.11 and partial results in Table 6.12. Assume a three-phase 100 MVA per unit base. TABLE 6.11 Bus input data for Problem 6.20 TABLE 6.12 Partially Completed Bus Admittance Matrix (Ybus) for Problem 6.30
With the system shown in figures, use 100MVA as system base, and 230 kV as base voltage along the transmission line. 1. Build the Y-bus matrix without the Load. What is the element Y12 in susceptance value? 2. If you are to convert the real power load to a shunt conductance, what is the value of the conductance in per unit?
Choose the right answer. 1. The symmetrical component method is …………. 2. Conditions for succesful operation of a power system ………،……….. and ………… 3. The reason we use the numerical methods in load flow analysis is ……….
Write current equations and determine the admittance matrix of the network Determine the load voltage VL at the 5th Bus-Bar, the current of the Load IL and the current of each generator.
Solve numerical : Following figure shows the one-line diagram of a two bus system. Take bus 1 as slack bus, bus 2 as load (PQ) bus. Neglect the shunt charging admittance. Obtain the bus admittance matrixYBUS and find V2 and δ2, power flows and line losses by using Fast decoupled power flow method. All the values are given in per unit on 100MVA base. Use a tolerance of 0.001 for power mismatch.
Gauss Seidal method is the least accurate method for power flow analysis. Select one: True False
A 200 bus power system has 160 PQ bus. For achieving a load flow solution by N-R in polar coordinates, the minimum number of simultaneous equation to be solved is
Question 1a) A network comprises of n buses. The voltage, current, active power, reactive power and admittance related to the k th bus are defined as Vk, Ik, Pk, Qk and Ykk. Deduce the following:i) Related load flow equationii) Gauss-Seidel algorithm for the load flow equation
In a load flow problem solved by Newton Raphson method with polar coordinates, the size of the jacobian is 100*100. If there are 20 PV buses in addition to PQ buses and a slack bus, the total number of buses in the system is _____
Table A.2 list values for real power generation and demand (P), reactive power generation and demand (Q) and voltage (V) at each bus. a) Obtain the bus admittance matrix of the 3-bus power system.