Q4) (2UMS): A state of stress is specified as shown in Figure (4), By using Mohr's circle determine the normal and shearing stresses and their directions on: a The principal planes? b-The planes of maximum shearing stress? c- The planes whose normals are at (+50°) and (+140°) with x-axis? show your results on complete sketches of differential elements. 40 MPa 50 MPa 80 MPa VA 80 MPa X 50 MPa 40 MPa Figure (4)

Q4) (2UMS): A state of stress is specified as shown in Figure (4), By using Mohr's circle determine the normal and shearing stresses and their directions on: a The principal planes? b-The planes of maximum shearing stress? c- The planes whose normals are at (+50°) and (+140°) with x-axis? show your results on complete sketches of differential elements. 40 MPa 50 MPa 80 MPa VA 80 MPa X 50 MPa 40 MPa Figure (4)

Principles of Geotechnical Engineering (MindTap Course List)

9th Edition

ISBN:9781305970939

Author:Braja M. Das, Khaled Sobhan

Publisher:Braja M. Das, Khaled Sobhan

Chapter10: Stresses In A Soil Mass

Section: Chapter Questions

Problem 10.1CTP: EB and FG are two planes inside a soil element ABCD as shown in Figure 10.50. Stress conditions on...

See similar textbooks

Similar questions

Refer to Figure P6.4. A strip load of q = 900 lb/ft2 is applied over a width B = 36 ft. Determine the increase in vertical stress at point A located z = 15 ft below the surface. Given: x = 27 ft. Figure P6.4
Two line loads q1 and q2 of infinite lengths are acting on top of an elastic medium, as shown in Figure P8.6. Find the vertical stress increase at A.
For the beam in the question above, determine the maximum shear stress. sketch thesection stress distribution.
From the given figure below and its properties, calculate the stress at the top where at the fixed end. (MPa) Properties: Beam width = 274 mmBeam height = 419 mmWLL = 8.86 kN/mWDL = 12.6 kN/mPu = 7 kNSpan of the beam = 8 mPrestressing force = 399 kNeccentricity = 127 mm
Question ) Forces of F1=3 kN from point B in the z direction, F2=5 kN from point C in the z direction and F3=8 kN in the y direction are acting on the arm in the figure. The lengths of the arm are also given as L1=0.18 m and L2=0.17 m. It is desired to determine the stress state of point A on the a-a section taken from the arm. The radius r of the section is r=0.3 m and the shear modulus of the arm material is G=79 Gpa. According to this; Question 1-A) Find the shear stress due to the shear force at point A. (Write your result in MPa.Question 2-B) Find the shear stress due to the torsional moment at point A. (Write your result in MPa.Question 3-C) Find the total shear stress at point A. (Write your result in MPa)Question 4-D) Find the normal stress caused by the normal force at point A. (Write your result in MPa Question 5-E) Find the normal stress caused by the bending moment at point A. (Write your result in MPa.)Question 6-F) Find the total normal stress at point A. (Write your…
Determine principle stresses and the maximum shear stress based assuming normal and shear stress a At in the picture. Draw mohrs circle with max shear and principle stresses and average normal stress.
The uniform sign has a weight of 1500 lb and is supported by the pipe AB, which has an inner radius of 2.75 in. and an outer radius of 3.00 in. If the face of the sign is subjected to a uniform wind pressure of p = 150 lb>ft2, determine the state of stress at points C and D. Show the results on a differential volume element located at each of these points. Neglect the thickness of the sign, and assume that it is supported along the outside edge of the pipe.
state of plane stress at a point is represented by the stress element below: A. Draw the Mohr’s Circle. B. Determine the principle stresses and draw the corresponding stress elements. C. Determine the maximum shear stress and draw the corresponding stress element. D. Find the stresses on an element inclined at 50o clockwise and draw the corresponding stress element. E. Provide a table illustrating the stress values as well as the inclination angles and compare the obtained values from Mohr’s Circle with those obtained fro
A very thin rectangular plate (see figure (a)) is subjected to a biaxial plane stress state (σx, σy). The width and height of the plate are b = 7.5 [in] and h = 2.5 [in], respectively. The measures show that the strains in the (x, y) directions are εxx = 2.85x10−4 and εyy = −1.90x10−4, respectively. Figure (b) shows a 2D front view of the plate. a) Draw and identify the principal stresses and the maximum shear stress on Mohr's circle. In what orientation does this maximum shear occur? b) Calculate the unit volume change e = εxx + ?εyy + εzz Note: remember that in a plane stress state we have σz = τxz = τyz = 0 and if it is also bi-axialwe have τyx = 0.
H1. A rectangular beam of 100mm wide and 150mm deep is subjected to Shear force of 30KN, Determine ratio of Maximum shear stress to Average shear stress. Derive the equation which is used to find out the shear stress.
For the state of stress shown in the figure. a. Determine the maximum and minimum principal stresses.b. Describe the location of the maximum principal stress from side BC.c. Describe the location of the maximum principal stress from side BD.d. Determine the maximum shear stress.e. Determine the normal and shear stresses at plane AB. A = 30 ,B = 50 , C = 10 ,D = 37
Determine the maximum of the following: Bearing Stress, Tensile stress, and Shear stress in MPa if P=115 kN Note: the figure given is provided for the three stress that is needed to solve