Q4) A capsule shaped tank is created by attaching two halves of sphere and a cylinder as shown in the figure. a) Write MATLAB script to find the diameter d that make the total volume of the tank equal to 12m³, find the dimeter with 0.001m accuracy, knowing that a-6m. b) Plot the relation between d and v. 4 sphere volume = 7³ cylinder volume = πr² a a

Q4) A capsule shaped tank is created by attaching two halves of sphere and a cylinder as shown in the figure. a) Write MATLAB script to find the diameter d that make the total volume of the tank equal to 12m³, find the dimeter with 0.001m accuracy, knowing that a-6m. b) Plot the relation between d and v. 4 sphere volume = 7³ cylinder volume = πr² a a

Name: Q4) A capsule shaped tank is created by attaching two halves of spher
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: Q4) A capsule shaped tank is created by attaching two halves of sphere and acylinder as shown in the figure.a) Write MATLAB script to find the diameter d that make the total volume of thetank equal to 12m?, find the dimeter with 0.001m accuracy, kno

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Here are these questions if I could get help with themIf a spherical storage tank holds 40,000 gallons (120,000 liters) of water,what diameter must it have?If a cylindrical storage tank has a 40-foot (12 m) diameter circular 05::=how high must it be to hold 1 million gallons (3 million liters)?If water is moving at a rate of 3.2 ft3/sec (90,000 cc/sec), how manygallons (liters) per minute is this?If the specific gravity of gold is 19.0. what is the weight of a cubic inch(cubic centimeter) of gold? A cubic foot (cubic meter)?
You are working with an imagined cubical pot of water, 1 meter on each side, sitting on a stove. Heat is applied to the bottom of the pot from the stovetop. The pot has been on the stove for a while, so the stovetop is hot and some heat has already been added to the water. Assume the water at the bottom of the pot is held at 99 degrees C , while the water at the top of the pot is cold, 4 degrees C. Compute the heat delivered by that 1 g of water at 99 °C into the layer of water at the top of the pot, assuming the latter is 1 meter square, 1 cm deep, and 4 °C. Start by solving the calorimetry problem (Section 14-4 in the text) to determine the final temperature of the top layer plus hot 1 gram from below. Then use that to determine how much heat was delivered in the hot water
Help me solve this USING MATLAB
Please show how to derive cagliotti function.
The density of liquid water at 25 degrees celsius equals 62.2lbs/cube ft. Suppose the KD DF stud at the top of the page weighs 13.35lbs. And suppose the KD DF stud is thrown into a swimming pool, Twater=25 degrees celsius. Based on data would the stud: sink completely, partually. or float completely
This is from my engineering mechanics bookI'm not that familiar with limits yet in integral calculus, and I'm not that good with advanced calculus yetand in the image is a solved problembut I don't understand the steps on how it got to the answercan you explain the steps to me and I think there were shortcuts made in the solution can you give me the longer version or tell me any fundamental formulas I should already know when solving this kind of problem, so I can understand how the book derived to the answer.
Don't skip steps. Show the complete solution for this problem. A golden breast plate weighing 18.63 kg Is dropped in a tub that Initially contains water. After the breast plate was totally submerged. the water level rises by 61.87 cm. The tub has a diameter of 6 centimeters and the breast plate was said to be made only from gold and silver Compute for the percentage of each component of the breast plate if the density of gold Is 19.3 g/cubic centimeter and silver has a density of 10.49 g/cubic centimeter.
please answer soon and show up 4 iteration in calcuation q2b
A tank, shaped like a cone has height 8 meters and base radius 3 meters long. It is placed so that the circular part is upward. It is full of water, and we have to pump it all out by a pipe that is always leveled at the surface of the water. Assume that a cubic meter of water weighs 10000 N, i.e. the density of water is 10000 N/m3. How much work does it require to pump all water out of the tank? Enter the exact value of your answer.
Lemar Supermarket sells about 200 000 kilos of milk annually. The milk ispurchased for 4 MU/kg. Holding costs are 1.40 MU/kg/yr. Each order costs 35 MU. If theshelf life of the milk is only 5 days, how many kilos should be ordered at a time. Please mention formulas and do it in detail so I can understand.
When you lift an object by moving only your forearm, the main lifting muscle in your arm is the biceps. Suppose the mass of a forearm with hand is 1.80 kg. If the biceps is connected to the forearm a distance of 2.50 cm from the elbow, how much force must the biceps exert to hold a 44.5 N (about 10 lbs) ball at the end of the forearm at distance of 35.0 cm from the elbow, with the forearm parallel to the floor, in Newtons? Use g = 10.0 m/s2.
Generalize Prob. as follows. Denote length AB asH , length BC as L , and angle ABC as θ . Let the dam materialhave specifi c gravity SG. The width of the dam is b .Assume no seepage of water under the dam. Find an analyticrelation between SG and the critical angle θ c for whichthe dam will just tip over to the right. Use your relation tocompute θ c for the special case SG = 2.4 (concrete).