Q5: For a unity feedback control system with the following feed forward transfer function K G(s) = (s + 1)(s +3) Answer the following: 1- A suitable design to achieve zero steady state error for step input is: a- PD compensator b- Lag compensator c- Lead compensator d- PI compensator 2- A suitable design to reduce the settling time of system's under damped response is: a- K adjustment b- PD compensator c- Lag compensator d- PI compensator 3- All possible range of K for stable closed-loop operation is: a- 00 c- 0

Q5: For a unity feedback control system with the following feed forward transfer function K G(s) = (s + 1)(s +3) Answer the following: 1- A suitable design to achieve zero steady state error for step input is: a- PD compensator b- Lag compensator c- Lead compensator d- PI compensator 2- A suitable design to reduce the settling time of system's under damped response is: a- K adjustment b- PD compensator c- Lag compensator d- PI compensator 3- All possible range of K for stable closed-loop operation is: a- 00 c- 0

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Ex. 449. K*G(s)=K*1/(s(s+3)(s+6)) is the FTF of a unity-feedback closed-loop system. Calculate the asymptote centroid and show it on a professional root locus plot. Draw the asymptote plot separately. Determine the break-away point and K at the break-away point and show both on the plots. Formal documentation required. ans: 3
For a unity-feedback system with G(s) = K / s(s + 20)(s + 40) operating with a 20% overshoot, design a compensator to decrease the settling time by a factor of 2 without affecting the percent overshoot:i. Find the uncompensated system's dominant poles, gain, and settling time. ii. Find the compensated system's dominant poles and settling time. iii. Find the compensator's pole position and required gain. (Assume the compensator’s zero is at -20).
Consider the unity-feedback control system with the following feedforward transfer function: G(s) = K / s(s2+4s+5) (1) Plot the root locus. (2) Determine closed-loop poles that have the damping ratio of 0.5. Find the gain value K at this point. (3) For what value of K is the overshoot less than 10% and the maximum rise time less than 1.5s.
Control System , Given transfer function, T (s) = αs + β / s^2 + (α + 2)s + β (i) Pick a pair of values for parameters α and β such that the closed-loop system is stable (ii) Pick a pair of values for parameters α and β such that the closed-loop step response exhibitszero steady-state error. (iii) Pick a pair of values for parameters α and β such that the closed-loop step response isunderdamped, exhibiting a settling time of 4/5 seconds and a peak time of π/7 seconds.
An uncompensated unity feedback system with certain deficiencies has no zeroes and poles at -1, -2 and -5. Answer the following questions based on the above description of the system Determine using an apt technique, the gain of the system at damping ratio 0.45
The margins of stability for K = 12 of the unit feedback system shown in the figure are given below. Phase crossover frequency : Wfc = 2rad/s Gain crossover frequency: wgc = 1.4rad/s Phase Margin = 16.8 degree Amplitude Margin Kg = 6dB (NOTE: Use 3 decimal places in your operations.) a) Calculate the amplitude margin for K 60. b) Calculate the point where the KG(jw) Nyquist Diagram intersects the negative real axis for K 60.
The unit in the figure below is given as G (s) in feedback system. When a unit ramp is applied to the input of the system, the steady-state error is 0.4% and when the unit step is applied to the input, the settlement time is desired to be 50 ms. So which of the following is a pole value of the closed-loop transfer function? G(s)=k/s(s+a)
Below is given the forward transfer function of a unity-feedback system.a) Determine the position, velocity, and acceleration error constants Kp, Kv, and Ka and the steady-state error for step, ramp, and parabolic inputs;b) If possible, use a proportional controller to give a steady-state error for ramp input of e_ss(ramp) ≤ 0.01; c) Determine the controller necessary to give zero steady-state error for a ramp input;d) Determine the controller necessary to give zero steady-state error for aparabolic input.
Ex. 840. A proportional controller, Kp, is desired for the plant 1/( (s) (s+ 7) (s+12) ). Design the unity feedback system so that the dominant poles indicate a closed loop step response with a 32% overshoot. What is Kp, zeta, wn, wd, Ts, Tp, velocity constant (Kv) and the resulting SS error for a ramp input, and the gain, Kp, for marginal stability. MATLAB is not required.
For the unity-feedback system with G(s) = K / s(s + 5)(s + 11): i. Find the gain K for the uncompensated system to operate with a 30% overshoot.ii. Find the peak time (Tp) and Kv for the uncompensated system.iii. Design a lag–lead compensator to decrease the peak time by a factor of 2, decrease the percent overshoot by a factor of 2, and improve the steady-state error by a factor of 30. Assume the lead compensator zero is at -5. Please specify all poles, zeros, and gains.
Given a unity feedback system with G (s) =K/ s (s+4). What is the value of K for a damping ratio of 0.5?
Electrical Engineering For a unit feedback system having the following gain functions: G(s) Ks - 4.21) s² (2 s +5.7) 2 (1) Draw the root trajectory. (2) Find the value of the gain K in which all three roots are real and have intermediate roots. (3) When it becomes as in (2), find the value of its root. -thanks you very much for the help ~~