Q5: Hot water in an open storage tank at 82.2 °C is being pumped at the rate of 0.379 m/min from this storage tank. The line from the storage tank to the pump suction is 6.1 m of 2 in schedule 40 steel pipe and it contains three elbows. The discharge line after the pump is 61 m of 2 in pipe contains two elbows. The water discharges to the atmosphere at a height of 6.1 m above the water level in the storage tank. Calculate the following: (a) All friction losses (b) Ws of the pump (c) Power of the pump if its efficiency 75%

Q5: Hot water in an open storage tank at 82.2 °C is being pumped at the rate of 0.379 m/min from this storage tank. The line from the storage tank to the pump suction is 6.1 m of 2 in schedule 40 steel pipe and it contains three elbows. The discharge line after the pump is 61 m of 2 in pipe contains two elbows. The water discharges to the atmosphere at a height of 6.1 m above the water level in the storage tank. Calculate the following: (a) All friction losses (b) Ws of the pump (c) Power of the pump if its efficiency 75%

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A pump takes water at 60 F from a largereservoir and delivers it to the bottom of anopen elevated tank 25 ft above the reservoirsurface through a 3-in ID pipe. The inlet tothe pump is located 10 ft below the watersurface, and the water level in the tank isconstant at 160 ft above the reservoir surface.The pump delivers 150 gal/min. If the total loss of energy due to friction in the pipingsystem is 35 ft-lb, per 1bm of fluid, calculatethe horsepower required to do the pumping.The pump-motor set has an efficiency of 55%.
2. A pump draws water from a lake delivered to a height of 50 meters above the lake and encounters 15 meters of headloss. Determine the pump power requirement in Kilo-Watts to deliver a constant supply of 500 Liters per second? The correct answer has a margin of 1 from exact answer. Velocity head is neglected.
A centrifugal pump draws water from a 38cm pipe from an open reservoir in which the water surface is 2.6m below the pump centerline and discharges through a 30cm pipe. At a point in the discharge 2.35m above the pump centerline a pressure gage reads 320 kPa gage. The discharge is 200Liters/sec, the head loss in the suction is 0.15m and in the discharge is 1.05m. Power input to the pump is 140hp. Determine the following: a. The total dynamic head in meters 36.923 41.527 39.188 b. The Water Power (WP) in kW 76.863 80.451 81.451 c. The pump efficiency in percent 77.659 73.596 80.876
C2. A conical tube is fixed vertically with its smaller end upwards and it forms a part of the pipeline. The diameter at the smaller end is 245 mm and at the larger end is 467 mm. The length of the conical tube is 1.8 m and the flow rate of the oil is 128 liters/s. The pressure at the smaller end is equivalent to a head of 9.7 m of oil. Considering the following two cases: (1) Neglecting friction, (without head loss) determine (i) the velocity at the smaller end in m/s, (ii) the velocity at the larger end in m/s, and (iii) the pressure at the larger end of the tube. (2) If a head loss (with head loss) in the tube is hL= 0.0153(V1-V2)2, where V1 is the velocity at the smaller end and V2 is the velocity at the larger end, determine (iv) the head loss in m of oil and (v) the pressure at the larger end of the tube.
The static head corresponding to a flow velocity of 10 m/S
1. Assume a horizontal shaft handling water at 65 deg C (Pv=2.503 KPa, Density=980.5 m3/kg). The suction nozzle is 4.35 m below the pump centerline and the pressure gauge reading at this point is 221Kpag. Determine the NPSHa if the head loss is 0.82 m. If the NPSHr is 3m less than the NPSHa you got on question number 1, determine the pump suction specific speed at pump rotating at 1800rpm and Q=500gpm
Toluene at 35 degrees Celsius is pumped from an open reservoir to a tank kept at a gauge pressure of 150 kPa. The pump itself is 3m below the reservoir, while the discharge tank is 10m above the reservoir. Assuming friction in the suction line is negligible, while in the discharge line the friction head amounts to 7.5 m, determine the net positive suction head available for the pump. If the pump has an efficiency of 65%, determine the total power input. At the given temperature, the density and vapor pressure of toluene are 862 kg/m3 and 40 mmHg
The diameter of the discharge pipe of pump is 15 cm and that of intake pipe is 20 cm. The pressure gage at discharge reads 257 kPa and a vacuum gage at intake reads 195mm Hg. The flow rate is 90000 L/min and the applied torque in the pump shaft is 6.5 kN.m for a mechanical efficiency is 88% determine a.) the pump used; b.) the pumps to be used for a four-parallel pump arrangement.
From a very large tank with an absolute pressure of 3 bar, the water is discharged to the atmosphere by means of 2 smooth pipes of 100 m length, 1 m and 50 m long, connected in series. The height difference between the water level in the tank and the outlet is 50m, and the diameters of the pipes are 50mm and 100mm, respectively. In addition, a 500kPa turbine is placed on the 2nd Pipe. a) Draw the system roughly, show the dimensions on it.b) Calculate the exit velocity of the water from the 2nd pipe, ignoring the local losses.
A pump draws water from open reservoir A at 20 ft above pump centerline and lifts to an open reservoir B at 280 ft above pump centerline. The loss of head at the suction is 3 times the velocity head at the 6 inches suction pipe and at the discharge is 20 times the velocity head at the 4 inches discharge pipe. The pump discharge is 200 GPM. a. The total dynamic head in ft. b. The water power in horsepower
A water turbine operating at 85% efficiency is under a head of 100 m. If the constant discharge is 1000 gallon/sec, evaluate the operating speed of the turbine.
24 m3/s of water flowing through the fixed vanes of a turbine, has a tangential velocity component of 2 m/s at a radius of 1.25 m and the impeller turning at 240 rpm discharges in an axial direction. Neglecting losses, what is head on the turbine.