Q7: A turbine is supplied with Steam at 40 bar, y00'c,wwhich expands through the turbine in Steady flow to an exit pressure of 0.2bar and adryness fraction of o.93. The inlet velocity is negligible but the Steam leaves at high velocity through a duct of oil4 m cross-Sectioral area.If the mass flow rate is 3 lgis, and the mechanical etticiency is 90%- Calculate the horse power output of the turbine - Show that the process is isreve- rsible and calculate the change of entropy,negligible the heat losses from the turbine.

Q7: A turbine is supplied with Steam at 40 bar, y00'c,wwhich expands through the turbine in Steady flow to an exit pressure of 0.2bar and adryness fraction of o.93. The inlet velocity is negligible but the Steam leaves at high velocity through a duct of oil4 m cross-Sectioral area.If the mass flow rate is 3 lgis, and the mechanical etticiency is 90%- Calculate the horse power output of the turbine - Show that the process is isreve- rsible and calculate the change of entropy,negligible the heat losses from the turbine.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Q3) Three pipes are connected in parallel Ly =1800m, Dy =045m, f4 =0.012. Lp=600m, Dg = 0.15m, fp = 0.020. Le =1500m, D = 0.3m, fe =0.015. L=1800m, D=045m D L=600mD=015m 7=0020 L=1500m, D=1500m 1=0015 Find: The pipe having the greatest velocity.
A simple turbomachine is constructed from a disk with twointernal ducts that exit tangentially through square holes, asin Fig. P3.156. Water at 20 ° C enters normal to the disk atthe center, as shown. The disk must drive, at 250 r/min, asmall device whose retarding torque is 1.5 N ? m. What isthe proper mass fl ow of water, in kg/s?
The energy loss between points 1 and 2 is 3.40 lb-ft/lb and the pump delivers 40 gal/min of fluid having a specific weight of 60.0 lb/ft3. What is the required hp of the pump? The inside diameter for the 2-in and 3-in schedule 40 steel pipes are 2.067 inches and 3.068 inches respectively
A heating plant for a large medical campus requires 5506 MBH (1MBH \= 1,000,000 btuh) of heating capacity. Which of the following pipe size and velocity in feet per second (fps) for the main would be needed if the plant is a 62 psig medium-pressure steam system? (Hint: Table 7.2) a.8" pipe at 130 fps b.4" pipe at 150 fps c.2" pipe at 100 fps d.4" pipe at 130 fps e.5506 MBH; 62 psig
Draught produced by stack 30 meters high for maximum rate of discharge of hot gases through it at 27°C is (a) 17.65 mm H₂O (b) 35.5 mm H₂O (c) 30 mm H₂O (d) Not possible to find with the data
Airat1500kPaabsoluteflowsin25mm-diamtertube.Whatisthe maximum laminar flow rate. Use density of air=14.04kg/cu.m and ?=0.0000217Pa-s
4. Atube15mlongistoconnecttwolargetankswhosedifference in water level is 2m. The tube is to carry 5L/s of flow. What minimum size of tube is necessary to assure laminar flow condition?
Answer only that SECOND question thanks. Water is issued verAticalFly at the rate of 35462 L/Ts through a 61515 mTm diamDSeter noASDzzle. What is the the maxiSmum heighDSt of watSDr can reaDSch. The nozzle which furnished the water to a certain hydraulic turbine 280 mm in diameter and has a coefficient of velocity and discharge of 0.98 and 0.95 respectively. The nozzle supplied from 60 cm in diameter pipe in which water approached the nozzle with a total head of 335 m. Compute for the power in kN/s delivered by the jet to the turbine
Design a main pipe to convey water from the channel to each of these facilities using Darcy Weisbach method for head loss calculation. Knowing that the pipe is made of galvanized iron assuming a 90 deg bent pipe system. (Include minor losses when calculating the head loss). For pipe in the follwing figure. Velocity = 1.235 m/s , Discharge through the pipeline, Q=45 m3/s (at 20°C)
A tank 10 ft high, has theform of a frustum of a cone,with diameters of 8” at thetop and 4” at the bottom. Thetank is to be filled oremptied with water through anorifice at the bottom having acoefficient of discharge of0.60. What size of orificewill completely fill the tankin 6 minutes?
1. A centrifugal fan supplies 4.7m3 / s of air at a total static pressure of 325Pa. If the fan efficiency is% 60 and rotates at a speed of 950rpm and supplies air with a velocity of 12m / s, determine the fan total pressure, air power, and fan power? Ans. 411 Pa 2. If the efficiency of the fan given in Problem - 1 becomes 70%, determine the power required for running it. Then, find the power required and airflow rate supplied if the fan speed is increased to 1050rpm. Also, assume that the fan static pressure does not change and determine the air velocity out of the fan. Ans. 4.6kW, 6.21kW, 5.195m3 / s, 17.2m /
Apipe through which water flowing is having Dia meter 30cm and 15 cm at Cross section 1, 2 respectiley. The velocity is water at section 1 4.5m/s.find kinetuc head at section 1,2 and Also rate of discharge