Question 10Define thermal bridge in buildings, and explain how thermal bridge can be controlled in thefollowing building components:Window frames:Balcony slab:Stud frame walls:Roof to wall connection:Window to wall connection:

Thermal bridge It is also known as the cold bridge in a building when the heat transfer is higher…

Question 10 Define thermal bridge in buildings, and explain how thermal bridge can be controlled in the following building components: ņ Window frames: Balcony slab: Stud frame walls: Roof to wall connection: Window to wall connection:

Question 10 Define thermal bridge in buildings, and explain how thermal bridge can be controlled in the following building components: ņ Window frames: Balcony slab: Stud frame walls: Roof to wall connection: Window to wall connection:

Residential Construction Academy: House Wiring (MindTap Course List)

4th Edition

ISBN:9781285852225

Author:Gregory W Fletcher

Publisher:Gregory W Fletcher

Chapter22: Solar Photovoltaic (pv) System Installation

Section: Chapter Questions

Problem 13RQ

See similar textbooks

Similar questions

A 2 x 2 m flat plate solar collector for domestic hot water heating is shown in the figure. The incident solar radiation on the glass cover, which transmits 90% of the incident flux, is 750 W/m2. Water flows through the tubes soldered to the backside of the absorber plate, entering at a temperature of 25°C. The temperature of the glass cover is 27°C, and it radiates heat with an emissivity of 0.92 to the sky at –50°C. Additionally, the glass cover losses heat by convection to air at 20°C flowing over its surface at 30 km/h. Assume that the radiation heat transfer between the absorber plate and glass cover and the heat transfer through the back and sides of the collector is negligible.
A diffuser in a pipe flow is basically a slow expansion of the pipe diameter, which slows down the fluid velocity and increases the pressure (the Bernoulli effect). Water at room temperature flows with a volume flow rate of 0.0250 m3/s through a horizontal diffuser in which the pipe diameter increases gradually from D1 = 6.00 to D2 = 11.00 cm. The irreversible head loss through the diffuser is estimated to be 0.450 m. The flow is turbulent, and the kinetic energy correction factors at both the inlet and outlet of the diffuser are assumed to be 1.05. Calculate the pressure difference P2 – P1 in units of kPa using the energy equation. (b) Repeat using the Bernoulli equation (ignore irreversible head losses and ignore kinetic energy correction factors—in other words, set the kinetic energy correction factors to 1). Calculate the percentage error in the result due to the Bernoulli approximation, and explain why (or why not) Bernoulli is applicable here. (c) It may be surprising that the…
Question 2. A coal fired power station requires an ESP for dust removal from the flue gas. The influent flu gas has a concentration of 5200 mg/m3 of dust particles and a flow rate of 150 m3/s. The smallest particles in the gas stream are 1.5 um in diameter, and all particles have a dielectric constant of 5.5. The emission standard is 50 mg/m3. Assume a plate-to-plate spacing of 30 cm and an applied voltage of 15,000 volts. Each plate is 20 m long and 15 m high. Estimate –a) The particle drift velocityb) The required collection-plate area and number of plates required.Assume – Standard temperature and pressure.
4. A town is covered by an inversion layer 500 m above the ground. The town’s area isapproximately rectangular with dimensions 9 km by 12 km. The incoming air is clean andthe wind is blowing at 3 m/s, parallel with the 12 km side of the town. SO2 emissions inthe town come from a number of small sources and average 0.0008 mg/m2-s. An industrialplant also emits 2,150 kg/day of SO2. Assume the air above the town is well-mixed.Calculate the state-state concentration of SO2 in the town’s air.
Air in a large tank, at 300 °C and 400 kPa, fl ows through aconverging-diverging nozzle with throat diameter 2 cm. Itexits smoothly at a Mach number of 2.8. According to onedimensionalisentropic theory, what is (a) the exit diameter,and (b) the mass fl ow?
Kelon Mus has another plan to build a mining factory at the surface of Edog-1. This mining factory will emit a massive amount of saturated air parcels which have the same temperature as the surrounding environment (40°C). Describe the vertical movement of the emitted air parcel, and possible changes in regional climate patterns(
The room pictured has the following absorption coefficients at 500 Hz: Floor: Carpet, α = 0.14 Ceiling: Acoustic Ceiling Tile, α = 0.70 Walls: Gypsum Wallboard, α = 0.10 Reference image attached below. a. Calculate the total absorption in this room b. Calculate the room constant. c. Calculate the critical distance. Assume Q=4. d. A source generates a sound power level, LW, of 102 dB. The directivity, Q, is 4. What sound pressure level, Lp, would be measured at a distance of 6 m in the room above?
S 1 Calculate the critical contact angle for a pillar surface with a pillar diameter of 10 microns spacing (center to center) of 40 microns and height of 30 microns. Also, what is the expected apparent contact angle for water on the surface if its functionalized by a fluorosilane with a Young’s contact angle = 120º. The pillars are arranged in a square array.
When you touch a hot object with your finger, the heat transferred to your finger is by Group of answer choices radiation none of these Conduction convection
Convert 15.14 poises to kinematic viscosity in square meter per second if the liquid has a specific gravity of 0.964
The city is 10 km wide and has a length of 10 km. The wind is blowing 7 m/s. The mixing height is 1000 m. Concentration in the city is 60 µg / m3. City has an emission rate of 17,5 x 10-7 g/s*m2. How much emission is entering the city from an upwind direction? Hint: use mathematical box model of air pollution
1. An unknown lamp placed 6m from a photometer screen provides the same illuminance as a 90 cd lamp placed 4 m from the screen. What is the candlepower of the unknown lamp? 2. The illuminance of a room 20 ft x 15 ft is being designed. The illuminance required is 50 footcandles. What is the total required lumens output of the lamp assuming room and luminaire efficiency of 42%?