Question 3. Design of the riveted joint of a structure, draw a designed sketch. The bracket plate is t (mm) thick. All rivets are to be of the same size. Load on the bracket, P (kN); rivet spacing. C=50...100 mm; load am, e (mm). Determine the size of the rivets to be used for the joint. Fig. P, kN t, mm e, mm Material 1 2 3 35

Question 3. Design of the riveted joint of a structure, draw a designed sketch. The bracket plate is t (mm) thick. All rivets are to be of the same size. Load on the bracket, P (kN); rivet spacing. C=50...100 mm; load am, e (mm). Determine the size of the rivets to be used for the joint. Fig. P, kN t, mm e, mm Material 1 2 3 35

Automotive Technology: A Systems Approach (MindTap Course List)

6th Edition

ISBN:9781133612315

Author:Jack Erjavec, Rob Thompson

Publisher:Jack Erjavec, Rob Thompson

Chapter40: Drive Axles And Differentials

Section: Chapter Questions

Problem 8RQ: The double-offset joint is typically used in applica tions that require______. a. higher operating...

See similar textbooks

Similar questions

A small stepladder has vertical rails and horizontal steps formed from a C-section aluminum channel. Two rivets, one in front and one in back, secure the ends of each step. The rivets attach the steps to the left and right hand rails. A 225 lb person stands in the center of a step. If rivets are formed of 6061-T6 aluminum, what should be the diameter d of the rivets? Use a factor of safety of 8 and round your answer to the nearest 1/16 of an in.
The double-offset joint is typically used in applica tions that require______. a. higher operating angles and greater plunge depth b. lower operating angles and lower plunge depth c. higher operating angles and lower plunge depth d. lower operating angles and greater plunge depth
1/2-inch thick steel bar is welded to the vertical supportA) Calculate the allowable load if the electrode is E7018, the bar is 1015 cold drawn steel, the support is 1020 cold drawn steel.
A horizontal plate using four rivets arranged as shown in figure. Determine the magnitude of the load?
Question 41. Two 10-mm-thick by 60-mm wide hot rolled SAE 1050 steel plates are to be butt-welded together with a CJP weld. Choose an appropriate electrode for tensile loading of the joint. 2. Find the torque that a 2-surface dry disk clutch can transmit if the outside and inside lining diameters are 120 mm and 70 mm, respectively, and the applied force is 10 kN. Assume uniform wear and μ = 0.4.
The maximum force in a rivet in a riveting group under eccentric loading
Question: a) A plate 100 mm wide and 10 mm thick is to be welded to another plate by means of double parallel fillets. The plates are subjected to a static load of 80 kN. Find the length of weld if the permissible shear stress in the weld does not exceed 55MPa. Determine the increase in load carrying capacity if a combination of single transverse double parallel fillet is used the permissible tensile strength of material is 80MPa. b) Draw a neat sketch of double riveted double cover but joint. If 8mm plates with 20 mm diameter rivets having a pitch of 50 mm are joint using double riveted lap joint. The permissible stresses are permissible tensile stress = 120 MPa;Permissible crushing stress= 100 MPa; Permissble shear stess= 150 MPa. Find the strengths and efficiency of joint, taking the strength of the rivet in double shear acoording to the indian boiler standards.
Question No. 11: (a) Illustrate flatness, straightness and circularity with symbol. (b) A circular shaft, 80 mm in diameter is welded to support by means of a circumferential fillet weld. It is subjected to a torsion moment of 3000 N-m. Determine the size of weld, if the maximum shear stress in the weld is not to exceed 70 N/mm2 . (c) Analyze different stresses during design of screw and nut
A circular steel bar 50 mm diameter and 200 mm long is welded perpendicularly to a steel plate to form a cantilever to be loaded with 5 kN at the free end. Determine the size of the weld, assuming the allowable stress in the weld as 100MPa.
(1) What are the methods used to obtain a good weld when welding steel when the carbon content is high? b) Find the appropriate size and length for the weld joint shown in the figure if the strength is equal to (70000Ib) and the allowable shear stress value is 40ksi and the weld rib dimension is (1/4in)
a) list two advantages and two disadvantages of welded joints b) Name the type of bonding forces applied in welded joints A plate 50mm wide by 11mm thick is joined with another plate 120mm wide by 11mm thick by parallel welds of 40mm long.if the permissible tensile and shear stresses are 110MPa and 80MPa respectively calculate; i) safe load F carried by the joint ii) Efficiency of the joint
The axial load 229kN applied to the lap joint is distributed equally among the three 17.1-mm-diameter rivets. What is the maximum tensile stress (in Mpa) in the plate if w=139.6mm and t=29mm? Round off the final answer to three decimal places.