Engineering

Civil EngineeringQ&A LibraryA member is made of the following materials: steel, brass and copper, the constants are listed below:STEEL:length: 300mmcoeff. of thermal expansion: 12(10^-6)/degree Carea: 200mm^2E= 200 GPaBRASS:L= 200mmA= 450mm^2Coeff of thermal expansion: 21(10^-6)/degree CE= 100 GPaCOPPER:L= 100mmA= 515mm^2Coeff. of thermal expansion: 17(10^-6)/degree CE= 120 GPaRigid supports are located at each end of the member. What is the force exerted on the supports if the temperature increases by 6 degrees C?Start your trial now! First week only $4.99!*arrow_forward*

Question

A member is made of the following materials: steel, brass and copper, the constants are listed below:

STEEL:

length: 300mm

coeff. of thermal expansion: 12(10^-6)/degree C

area: 200mm^2

E= 200 GPa

BRASS:

L= 200mm

A= 450mm^2

Coeff of thermal expansion: 21(10^-6)/degree C

E= 100 GPa

COPPER:

L= 100mm

A= 515mm^2

Coeff. of thermal expansion: 17(10^-6)/degree C

E= 120 GPa

Rigid supports are located at each end of the member. What is the force exerted on the supports if the temperature increases by 6 degrees C?

Tagged in

Engineering

Civil Engineering

Find answers to questions asked by students like you.

Q: subject : Geotechnical Design Book : PRINCIPLE OF FOUNDATION ENGINEERING

A: q =γ H = 17 x 10 = 170 kN/m², Z= 5 mThe embankment is divided into blocks as shown in figure for mak...

Q: 30 Kip ISin Zin k혀 3i 12o 26 ZA-45) 20 zin 243 -160 beam @gn19ου T dend:Fg14 s hea-han, alo-g Cross ...

A: As per the given shear force and bending moment diagram.From bending equation, we have

Q: subject : Geotechnical Design Book : PRINCIPLE OF FOUNDATION ENGINEERING

A: We have been given the following information:

Q: Draw shear force and bending moment diagrams for the given simply supported beam.

A: Draw a free body diagram converting the UDL into a point loadAs UDL is given 5kn and it is acting on...

Q: A beam is constructed from three boards bolted together as shown. Determine the shear force develope...

A: Let' s calculate Y

Q: A dilatometer test was conducted in a sand deposit ata depth of 6 m. The groundwater table was locat...

A: Following is the figure fetched from the given information.

Q: Give one or two possible identifications for each of the following. Provide a group symbol and descr...

A: No soil particles are discernible by eye, yet the soil, even when wet, falls apart when an attempt ...

Q: For the given statically indeterminate beam find: Deflection diagram Moment equation of the beam Us...

A: Solution:Given:The load act on a beam (w) is 600lb/ft.The length of the beam (L) is 15 ft.Calculatio...

Q: For the beam below, use the deflection tables from the FE equation packet to determine the displacem...

A: Determine the reaction at support A using the relation.

Q: The control linkage for a machine consists of two L2 steel rods BE and FG, each rod has a diameter o...

A: Show the free body diagram of the control linkage as in Figure (1).

Q: how come I can't get a accurate sq. root calculation with three different calculators ?

A: We can say that calculators are very accurate and do give the values usually decimals. If you take t...

Q: The offset link has a width of w=200mm and a thickness of 40mm. The allowable normal stress is 80 MP...

A: Find the area of the offset link for the link width of 200 mm and thickness of 40 mm.

Q: A series of cantilever beams are extending off reinforced concrete columns in a building. The cantil...

A: Determine the modular ratio.

Q: subject : Geotechnical Design Book : PRINCIPLE OF FOUNDATION ENGINEERING

A: Given:γ D = 105 lb/ft³, γ B (sat)= 118 lb/ft³B= 5ftD2= 4ftD1=2ftC= 0Ø=35°

Q: 3.25 In a site consisting entirely of clays, an electric friction cone penetrometer measures the con...

A: We have been given the following information,Cone resistance qc = 0.75MN/m2 at a depth of 8m.Water t...

Q: For the given statically indeterminate beam find: Deflection diagram Moment equation for the beam U...

A: We have the following set of reactions at the points A, B and CAt A two reactions, at B one reaction...

Q: Determine the state of stress a point A on the cross section a-a, finding the normal and shear stres...

A: Show the free body diagram of the beam and section a-a as in Figure (1).

Q: Develop the generalized piecewise equation for the elastic curve for the beam as a function of x ref...

A: Given information:The point load act at right end of the beam is P.The flexural rigidity of the beam...

Q: Determine the stress in the steel and in the wood if the beam is subjected to a moment of 750 lb-ft....

A: We have been given the following data:The beam is subjected to a moment of 750 lb-ft.E steel = 29,0...

Q: A storage tank if fabricated by bolting together two half cylindrical shells as shown. The tank is d...

A: Determine the required thickness of the cylindrical shell as shown below:The inner diameter of the t...

Q: What is the difference between oblique, isometric, orthographic, elevation, plan, and section drawin...

A: Drawings are a commonly used mode of communication in the engineering industry, As such drawing is ...

Q: Develop the generalized piecewise equation for the elastic curve for the beam as a function of x ref...

A: We will have to develop a generalized piecewise equation that should be in terms of P, x, and L fo...

Q: The frame is subjected to the horizontal force and couple moment. Determine the priciple stresses an...

A: Determine the moment of inertia of the cross section:The width of the section is 0.15 m and the dept...

Q: New technologies have benefited sociological research by facilitating surveys and statistical analys...

A: Tests of hypothesis are only useful aids for decision making.Test do not explain the reasons as to w...

Q: Problem Statement: A member having the dimensions shown is used to resist an internal bending moment...

A: We are given the following data

Q: subject : Geotechnical Design Book : PRINCIPLE OF FOUNDATION ENGINEERING

A: We are given the following data

Q: subject : Geotechnical DesignBook : PRINCIPLE OF FOUNDATION ENGINEERING

A: We have been given the following data:

Q: Three A36 steel bars are pin connected at the apex, point A, and at the three lower rigid supports t...

A: Given Data:Cross Sectional Area of bar = 2 in 2∆T= 100 degrees FE for A36 steel = 29000 ksiCoeff. of...

Q: subject: Geotechnical Engineeringbook: principle of foundation engineering - Braja M Das

A: Part A.For consolidated drained triaxial test:Determine the major principal effective stress of a cl...

Q: A steel bar, whose ultimate tensile strength is 150,000 psi is subjected to fluctuating tension-comp...

A: Determine the minimum diameter of the bar to prevent fatigue failure:Let consider the cross sectiona...

Q: A strain gage located at C on the surface of bone AB indicates that the average normal stress in the...

A: First of all we will write the equation of the stress as shown below:Here, F represents force A repr...

Q: Determine the maximum shear stress acting at section a-a of the cantilevered strut.

A: we have been given the following information:

Q: Give one or two possible identifications for each of the following. Provide a group symbol and descr...

A: Solution to the given scenario:Unified soil classification system:A soil which is more than 50 % ret...

Q: The shaft is made from a solid steel section AB and a tubular portion made of steel having a brass c...

A: Given:TorqueShear modulus of steelShear modulus of steel

Q: A 1.0 meter long A36 steel rod with a diameter of 40mm is lightly attached at both end of the rod, e...

A: We have been given the following data:Length of the rod = 1m.Diameter of the rod = 40 mm.Initial tem...

Q: subject : Geotechnical DesignBook : PRINCIPLE OF FOUNDATION ENGINEERING

A: Part A:-we have the following loading condition andIn triangle XYZ, we have

Q: subject : Geotechnical Design Book : PRINCIPLE OF FOUNDATION ENGINEERING

A: Click to see the answer

Q: subject : Geotechnical DesignBook : PRINCIPLE OF FOUNDATION ENGINEERING

A: Given:

Q: 3.15 In a site consisting of normally consolidated clean sands, the water table is at 10 ft depth. T...

A: Given :

Q: E=160 GPa I= 65.0*106mm4 What is the slope and deflection at the end of the beam?

A: Given,

Q: subject: Geotechnical Engineeringbook: principle of foundation engineering - Braja M Das

A: Determine the effective stress at the top of the clay layer before lowering the water table using th...

Q: subject: Geotechnical Engineeringbook: principle of foundation engineering - Braja M Das

A: Soil A with a hump indicates that some of the intermediate size particles are missing. This type of...

Q: The bean is fabricated from two equivalent structural tees and two plates. Each plate has a height o...

A: Lets calculate I at Neutral axis

Q: The shaft is made of two segments. AC has a diameter of 0.5in, and CB has a diameter of 1in. It is f...

A: Find the minimum shear stress in the shaft as follows:Let the torque at end A be TA and the torque a...

Q: Draw shear force and bending moment diagrams for the given simply supported beam.

A: Draw a free body diagram converting the UDL into a point loadAs UDL is given 5kn and it is acting on...

Q: subject : Geotechnical Design Book : PRINCIPLE OF FOUNDATION ENGINEERING

A: We are given the following data

Q: subject : Geotechnical Design Book : PRINCIPLE OF FOUNDATION ENGINEERING

A: We are given the following data

Q: Give one or two possible identifications for each of the following. Provide a group symbol and descr...

A: Solution to the given scenario:The size of the gravel is larger and the size which is greater than 2...

Q: subject : Geotechnical Design Book : PRINCIPLE OF FOUNDATION ENGINEERING

A: Click to see the answer

Q: Determine the elastic curve for the cantilevered W14x30 beam using the x-coordinate. Specify the max...

A: Click to see the answer