Answered: rectangular bar 40 mm wide and 30 mm…

rectangular bar 40 mm wide and 30 mm thick is 0.5 m long. It is acted upon by axial tensile force of 120 KN. Find Change in dimensions of the bar. (E = 200 Gpa and μ=0.25.)

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter1: Tension, Compression, And Shear

Section: Chapter Questions

Problem 1.7.2P: A round bar of 10 mm diameter is made of aluminum alloy 7075-T6 (see figure). When the bar is...

See similar textbooks

Related questions

Q: Mechanics of Deformable Bodies The rigid beam of negligible weight is supported by a pin at o and…

Q: A steel cable is used to lift a load W with the following given. weight W = 175 kN diameter = 30.03…

Q: The cross-sectional area of the figure below is 0.5 in2. If E = 13 x 106 psi, calculate the total…

Q: If an isotropic material has a shear modulus of 21 Gpa and a Poisson's ratio of 0.4, calculate its…

A: The relation between Young's modulus, shear modulus, and Poisson's ratio is given as: E = 2G (1+μ) E…

Q: teel bar of 40 mm x 40 mm square cross section is subjected to an axial compressive load of 200 kN.…

A: Given:Load, P=200 kNcross-section, A=40×40 mm2modulus of elasticity, E=200 GPaLength of the bar, L=2…

Q: A steel rod has length 51.4 cm and radius 2.20 cm. An aluminum rod has length 39.2 cm and radius…

Q: 1. A circular aluminium tube of length L = 400 mm is loaded in compression by the force P. The…

A: 1. Given: The length of tube, L = 400 mm The outside diameter of tube, D = 60 mm The inside diameter…

Q: The figure below is a stress strain curve for an alloy of aluminum at various temperatures. a) What…

A: (a) Draw the line at the Centre between the temperatures 250k and 350k. This line gives line of 298k…

Q: Q 3 A square steel bar 50 mm on a side and 1 m long is subject to an axial tensile force of 250 kN.…

Q: Find out the crippling stress of the column if E=2×105N/mm2 . Also, find out the shortest length of…

A: Given: Fix-hinge support do=40 mm=0.04 mdi=20 mm=0.02 mL=5 mE=2×105 N/mm2σy=250 N/mm2 To determine:…

Q: Calculate the extension of the bar (△L).

A: Calculate the extension of the bar (△L)

Q: A bar of titanium alloy of length 120mm and square cross – section, 7.5 mm x 7.5 mm, is pulled…

A: Given that length of bar, l=120mm =120×10-3marea of cross section , A=(7.5×7.5)mm2…

Q: Figure 5 shows a steel rod of 200 mm length (L) with modulus of elasticity, E = 200 GPa and…

Q: A wire 20 m long, weighing 0.8 N per m, and having a cross sectional area of 6.2 mm2, is suspended…

Q: The cylindrical rod BC, diameter 3.6 mm made of steel supports the AD bar with a distribution of…

A: Given data dBC=3.6mm E=200 GPa

Q: 1. Steel bars AB, CD and EF (E=200 GPa) are under the influence of 36 kN P load. bars AB and CD each…

A: The force which is incident towards a cross-section is termed a compressive force. The stress which…

Q: aluminum rod is hanging from one end. The rod is 1 m long and has a square cross section 20 mm by 20…

Q: Shown below is a torsion bar with a torque applied a distance L1 from one end. Th two ends are fixed…

Q: Calculate the total deformation of steelbars shown in Figure. (d1=1A mm, d2=2A mm and E=210 GPa)…

A: Given, A=5B=3C=8d1=1A mm=1×5 mm=5 mm=5×10-3 md2=2A mm=2×5 mm=10 mm=10×10-3 m E=210 GPa=210×109 Pa…

Q: Problem # 1: A rectangular bar is subjected to tensile forces of 2230 KN. Use E = 110 GPa and v =…

A: GivenP=2230kNE=110GPaν=0.34

Q: A 12-mm thick steel tire has a width of 110 mm and internal diameter of 800 mm. It is heated and…

Q: A steel bar with the dimensions and cross section shown is suspended vertically. Three concentric…

A: The change in length due to 22250 N force is ∆L1=PLAE=22250×1+0.65+0.356.5×10-4×210×109=3.26×10-4 m…

Q: Two springs are arranged in parallel with spring constants 21 N/mm and 34 N/mm. A force of 224 N is…

Q: 3.3. A steel bar with the dimensions and cross section shown is suspended vertically. Three…

Q: 4 The rectangular block of material of length L and cross-sectional area A fits Snugly between two…

A: The internal resisting force applied by the object when an external force is applied on the object…

Q: A wire of diameter 2mm and length 5m is stretched by a load of 10kg. Find the extension produced in…

Q: Consider a cylindrical specimen of a steel alloy (see figure below) 15.0 mm in diameter and 75 mm…

A: Given:d=15 mmL=75 mmP=20,000 N

Q: 4. An unknown metal cube measures 3.5 x 10 -2m decreases a volume of 5.8 x 10 -8m ³. At what stress…

Q: Two helical springs A and B with ground ends are made of the same material and are in parallel. The…

Q: (1) Find the factor of safety allowed in a piston rod 200 mm diameter if the maximum tensile pull in…

A: Given data: d=200 mmF=1 MNσS=600 MPa Need to determine the factor of safety allowed in a piston rod.

Q: A steel wire 30 ft long, hanging vertically, supports a load of 500 lbf. Neglecting the weight of…

A: Given- Load=500 lbf = 2224.11 NStress (σ) = 20,000 psi = 137.9 MPaThe elongation in the bar is zero,…

Q: 30. A compressive load P is transmitted through a rigid plate to three magnesium-alloy bars that are…

Q: bar is 250 mm long and 10 mm square over part of its length, the remainder being circular with a…

A: as per our company guidelines we are supposed to answer only first three sub-parts. Kindly repost…

Q: A solid 0.12 in. diameter steel (E = 30,000 ksi: a = 6.5 × 10-6/°F] wire is stretched between fixed…

Q: A solid homogeneous truss tie-rod has a diameter of 9.52 mm and an original length of 1.75 m…

Q: A steel is 10 mm diameter and 2 m long. It is stretched with force of 20 kN and extends by 0.2 mm…

Q: The ratio of modulus of rigidity to bulk modulus for a Poisson's ratio of 0.25 would be: (а) 2/3 (с)…

A: Given, Poisson's ratio = μ = 0.25 From the relation between Young's modulus and Modulus of…

Q: A vertical bar consists of three prismatic segments A,, A, and A, with cross-sectional areas of…

Q: A 200 kg load is hung on a wire of length 4 m, cross sectional area of 0.2 x 10 -4 m2 and Young’s…

A: Given data: The mass hanged in the wire is m = 200 kg. The length of the wire is L = 4 m. The area…

Q: A Steel wire hangs vertically under its weight. What is the greatest length it can have if the…

A: Given:- A Steel wire is hanging vertically under its weight Density of the wire (ρ)= 80 kg/m3…

Q: Find the modulus of elasticity of a brass rod of cross section 20 mm x 20 mm, and length 248 mm…

Q: A bar is subjected to fluctuating tensile load from 20 kN to 100 kN .The material has yield strength…

A: Given: The fluctuating tensile load in a bar,P1=20 kNP2=100 kNσyt=240 MPaσe=160 MPaFactor of safety,…

Q: steel bar 300 mm long, 50 mm wide and 40 mm thick subjected to a pull of 300 kN in the direction of…

A: Given data ,Length L=300 mmPull force P=300 KNE=2x105 MPam=4u=14=0.25

Q: A rod is 0.5 m long and 5 mm diameter. It is stretched 0.06 mm by force of 3 kN. Calculate stress…

A: Length of the rod, L= 0.5 m= 500 mm Diameter of the rod, d= 5 mm Length stretched, ∆L= 0.06 mm…

Q: 6.) A steel bar 100 mm long and having a square cross section 20 mm on an edge is pulled in tension…

Q: The rigid bar AC is supported by two axial bars (1) and (2). Both axial bars are made of bronze [E =…

A: Givenbar material →bronzeE=100Gpaα=18×10-6mm/mmοCA1=180mm2A2=380 mm2L1=1290 mmL2=2000 mma=590…

Q: A uniform bar with an area of 0.25 in2 is pulled between two points. The tensile force at a…

Q: A steel wire is 10m long supports a tensile load of 2000N. What is the diameter if the stress is 140…

Q: A steel [E = 200 GPa] rod with a circular cross section is 8-m long. Determine the minimum diameter…

Q: • Two Identical circular rods of same diameter and same length are subjected to same magnitude of…

A: as per the guidelines i can give the answer only first question so please upload the question again…

Concept explainers

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.

Question

100%

A rectangular bar 40 mm wide and 30 mm thick is 0.5 m long. It is acted upon by axial tensile force of 120 KN. Find Change in dimensions of the bar. (E = 200 Gpa and μ=0.25.)

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step by step

Solved in 4 steps with 4 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A wine of length L = 4 ft and diameter d = 0.125 in. is stretched by tensile forces P = 600 lb. The wire is made of a copper alloy having a stress-strain relationship that may be described mathematically by =18,0001+30000.03(=ksi) in which is nondimensional and has units of kips per square inch (ksi). (a) Construct a stress-strain diagram for the material. (bj Determine the elongation, of the wire due to the Forces P. (c) IF the forces are removed, what is the permanent set of the bar? (d) If the forces are applied again, what is the proportional limit?
The rails of a railroad track are welded together at their ends (to form continuous rails and thus eliminate the clacking sound of the wheels) when the temperature is 60°F. What compressive stress ?? =6.5×10-6 /? is produced in the rails when they are heated by the sun to 120"F if the coefficient of thermal expansion a = the modulus of elasticity E = 30 × 106 psi?
Determine the strain energy per unit volume (units of psi) and the strain energy per unit weight (units of in ) that can be stored in each or the materials listed in the accompanying table, assuming that the material is stressed to the proportional limit. DATA FOR PROBLEM 2.7-5 Material Weight Density (lb/in3) Modulus of Elasticity (ksi) Proportional Limit (psi) Mild sleel 0.284 30,000 36,000 Tool steel 0.284 30,000 75,000 Aluminum 0.0984 10,500 60,000 Rubber (soft) 0.0405 0.300 300
A round bar of 10 mm diameter is made of aluminum alloy 7075-T6 (see figure). When the bar is stretched by axial forces P, its diameter decreases by 0.0 16 mm. Find the magnitude of the load P. Obtain the material properties from Appendix 1.
A plastic rod AB of length L = 0.5 m has a diameter d1= 30 mm (see figure). A plastic sleeve CD of length c = 0.3 m and outer diameter d2= 45 mm is securely bonded to the rod so that no slippage can occur between the rod and the sleeve. The rod is made of an acrylic with a modulus of elasticity E1= 3.1 GPa, and the sleeve is made of a polyamide with E2= 2.5 GPa. (a) Calculate the elongation d of the rod when it is pulled by axial forces P = 12 kN. (b) If the sleeve is extended for the full length of the rod, what is the elongation? (c) If the sleeve is removed, what is the elongation?
To support a tensile load of 65 kN, a metallic rod with a circular cross section and a length of 0.32 m will be used. It is desirable that the tension in the bar should not exceed 240 MPa and the maximum elongation should be 0.42 mm. What is the minimum rod diameter [m] in these conditions? Calculate. (For a metallic bar, take the elastic modulus as 220 GPa).
To support a tensile load of 65 kN, a metallic rod with a circular cross section and a length of 0.32 m will be used. It is required that the tension in the bar does not exceed 240 MPa and the maximum elongation is 0.42 mm. What is the minimum rod diameter [m] in these conditions? (Elasticity for metallic bar take the module as 220 GPa).
(a) A 25 mm diameter bar is subjected to an axial tensile load of 100KN. Under the action of this load a 200 mm gauge length is found to extend 0.19 x 10-mm. Determine the modulus of elasticity for the bar material.
A copper rod of diameter 10 mm and length 4 m has a tensile force of 5 kN applied on it . Modulus of Elasticity of Copper is 96 GPa. Calculate the stress in MPa and extension in mm .
A bar of length 5 m is subjected to an axial tensile out of 100 KN The bar is 25 min diameter for 2 mof its length 30 mm diameter for I mor its length, and 20 mm diameter for the remaining 2 m of its length, Taking E= 2 x 10' Calculate the total increase in length of the bur.
A bar made up of two square sections , one of steel and the other of aluminium is shown in Fig.2 The bar is acted upon by a compressive force P. Determine the value of P if the total decrease in length of the bar is 0.3 mm . Take Esteel = 205 GPa and Ealuminium = 75 GPa .
A 2.25 m long solid bar (Lo) with a 32 mm diameter is placed under tension by a load (F) of 250 kN. The bar is solid and made of a homogeneous material with a Young’s Modulus E = 250 GPa. Calculate the extension of the bar (△L). Give your answer in millimeters (mm) to two decimal places.