SEÇT Aqud FClutquessv veion)(Matitesum pthedblum prt gen(AnsweQuestion 1A car manufacturing company is in the process of testing a new vehicular transmission system. Figure 1shows an outline of the system arrangement. As usual, the power generated by the engine is smoothed outby a flywheel at the end of the camshaft. A multi-plate clutch is affixed to the flywheel and transfers powerto the main shaft via the layshaft.Engine234 5RMainShaftClutch & flywheelLayshaftFigure 1: Schematic of transmission arrangementThe output torque from the engine is given by the expression: 510 + 46 sin 20 Nm, per rotational cycle andspins at an average of 4000 rpm. The attached flywheel has a coefficient of speed fluctuation of 0.15.Assuming a constant load torque requirement, determine:a) The maximum fluctuation of energy and the average power output at the flywheel face.b) The mass moment of inertia of the flywheel.c) The maximum and minimum speeds of the flywheel.

The question is incomplete because it is not possible to have coefficient of fluctuation of energy…

SECT A qud FClutquesv veiion) (Matitesum ptherblum prt gen (Answe Question 1 A car manufacturing company is in the process of testing a new vehicular transmission system. Figure 1 shows an outline of the system arrangement. As usual, the power generated by the engine is smoothed out by a flywheel at the end of the camshaft. A multi-plate clutch is affixed to the flywheel and transfers power co the main shaft via the layshaft. Engine 導導尊幕鼻皇真 23 45 Main Shaft Layshaft Clutch & flywheel Figure 1: Schematic of transmission arrangement e output torque from the engine is given by the expression: 510 +46 sin 20 Nm, per rotational cycle ane ins at an average of 4000 rpm. The attached flywheel has a coefficient of speed fluctuation of 0.15 Esuming a constant load torque requirement, determine: a) The maximum fluctuation of energy and the average power output at the flywheel face. b) The mass moment of inertia of the flywheel. c) The maximum and minimum speeds of the flywheel. R國寸

SECT A qud FClutquesv veiion) (Matitesum ptherblum prt gen (Answe Question 1 A car manufacturing company is in the process of testing a new vehicular transmission system. Figure 1 shows an outline of the system arrangement. As usual, the power generated by the engine is smoothed out by a flywheel at the end of the camshaft. A multi-plate clutch is affixed to the flywheel and transfers power co the main shaft via the layshaft. Engine 導導尊幕鼻皇真 23 45 Main Shaft Layshaft Clutch & flywheel Figure 1: Schematic of transmission arrangement e output torque from the engine is given by the expression: 510 +46 sin 20 Nm, per rotational cycle ane ins at an average of 4000 rpm. The attached flywheel has a coefficient of speed fluctuation of 0.15 Esuming a constant load torque requirement, determine: a) The maximum fluctuation of energy and the average power output at the flywheel face. b) The mass moment of inertia of the flywheel. c) The maximum and minimum speeds of the flywheel. R國寸

Automotive Technology: A Systems Approach (MindTap Course List)

6th Edition

ISBN:9781133612315

Author:Jack Erjavec, Rob Thompson

Publisher:Jack Erjavec, Rob Thompson

Chapter41: Automatic Transmissions And Transaxles

Section: Chapter Questions

Problem 9RQ: Overrunning clutches are capable of_______. a. holding a planetary gear member stationary b. driving...

See similar textbooks

Similar questions

The 12B series chain was chosen to deliver 12 kW of power from the electric motor at 1400 rpm. The transmission ratio is 2. What is the diameter of the pitch driving circle and diven sprocket?
Which clutch would you use to connect two spindles with a 250 angle between them? Why you chose this clutch, in terms of uniform moment transmission? Explain that it must meet the requirements.
the figure shows a motor driving a two-output transmission system. The blower requires a certain amount of force to operate since the drum rotates at an angular acceleration of 0.03 rad/s2. Determine the torque produced by a motor with a torque of 700 Nm and a speed of 1,600 rpm. following:- The power produced at the drum (P). The torque requirement for the blower to operate (Tblower) and power generation (Pblower) The overall efficiency transmission of the gear system, hO. If the speed of motor is NOT given, explain without calculation how the overall efficiency transmission of the gear system can be obtained. Given:- Number of gear teeth, t:- t1=40 ; t2=200 ; t3=50 ; t4=200 ; t5=40 ; t6=120 ; t7=60 and t8=120 Equivalent mass moment of inertia, Ieq:- Imotor,5=25 kgm2 ; I23=10 kgm2 ; Iblower,4=15 kgm2 ; I67=20 kgm2 and Idrum,8=60 kgm2 Friction torque in bearing, Fb:- A=F=25 Nm ; I=J =20 Nm ; B=C=G=H=5 Nm and D=E=10 Nm Efficiency of all gear mesh, ⴄ=85%
Define the term gearbox ratio.
Overrunning clutches are capable of_______. a. holding a planetary gear member stationary b. driving a planetary gear member c. both a and b d. neither a nor b
The larger diameter and face of the disk of a multiple disk chutch are 225 mm and 20 mm respectively. The load applied to the spring of the clutch axially is 1500 N. Assuming that there are 8 pairs of friction 0.18 and tuning 800 rpm. Find the power transmitted by the clutch using uniform pressure method. (Ans, 13.67 kW)
See the answer A flat belt drive system is to be designed for an application in which the input shaft speed (driving pulley) is 1725 rpm, the driven shaft speed is to be approximately 960 rpm, and the power to be transmitted has been estimated as 3.0 horsepower. The driven machine has been evaluated and found to have characteristics of moderate shock loading during operation. The desired center distance between driving and driven pulleys is approximately 18 inches.
What is used in a typical 4WD pickup truck to prevent driveline windup during turns?a. Constant velocity joints in the driveshaftsb. The haldex clutchc. An interaxle differential in the transfer cased. Axle disconnectscould it be d?
What is the extreme transmission angle values by using maxima and minima condition, of the transmission angle occur when the crank is perpendicular to the slider path in a slider-crank linkage.
Starter is used to transmit initial mechanical power to the car engine and the analysis will be based on this initial power input. Starter power is 1 hp, rotates at 250 rpm and has 10 teeth. The crankshaft has 48 teeth and camshaft has 60 teeth. Determine torque delivered by the camshaft? If the timing belt has 10 teeth/in, find its speed in in/min?
A 1000 RPM speed reducer and 12KW power drives a conveyor belt at 400 RPM. the distance between the centers is approximately 800mm. Select a suitable chain for transmission, as follows:1) Solicitation with moderate shock, abnormal operating conditions, operating 24 hours a day.
2a-e. Outline five transmission problems its causes and their solutions.