Select the piece of equipment that should be used to carry out the specified task in each example. 1. Accurately measuring the volume of a liquid graduated cylinder beaker Erlenmeyer flask pipet RD 2. Removing solid chemicals from a reagent bottle tongs pipet beaker spatula - - 3. Rrecisely transferring a specific volume of solution from one container to another pipet volumetric pipet graduated cylinder beaker 4. Holding approximately 250 mL of liquid volumetric flask buchner funnel beaker graduated cylinder 5. Heating a water bath to boiling hot plate wire gauze buchner funnel ring stand - 6. Dispensing or delivering an accurately measured volume of liquid into a container graduated cylinder beaker volumetric flask burette - 7. Preparing a solution that is precisely 100 mL volumetric flask Erlenmeyer flask pipet beaker 8. Cooling hot glassware spatula wire gauze burette clâmp hot plate - - 9. Filtering or separating a precipitate from a solution Erlenmeyer flask pipet buchner funnel tongs - 10. Swirling a solution to thoroughly mix without splashing Erlenmeyer flask beaker funnel graduated cylinder - -

Select the piece of equipment that should be used to carry out the specified task in each example. 1. Accurately measuring the volume of a liquid graduated cylinder beaker Erlenmeyer flask pipet RD 2. Removing solid chemicals from a reagent bottle tongs pipet beaker spatula - - 3. Rrecisely transferring a specific volume of solution from one container to another pipet volumetric pipet graduated cylinder beaker 4. Holding approximately 250 mL of liquid volumetric flask buchner funnel beaker graduated cylinder 5. Heating a water bath to boiling hot plate wire gauze buchner funnel ring stand - 6. Dispensing or delivering an accurately measured volume of liquid into a container graduated cylinder beaker volumetric flask burette - 7. Preparing a solution that is precisely 100 mL volumetric flask Erlenmeyer flask pipet beaker 8. Cooling hot glassware spatula wire gauze burette clâmp hot plate - - 9. Filtering or separating a precipitate from a solution Erlenmeyer flask pipet buchner funnel tongs - 10. Swirling a solution to thoroughly mix without splashing Erlenmeyer flask beaker funnel graduated cylinder - -

Chemistry

10th Edition

ISBN:9781305957404

Author:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Publisher:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Chapter1: Chemical Foundations

Section: Chapter Questions

Problem 1RQ: Define and explain the differences between the following terms. a. law and theory b. theory and...

See similar textbooks

Similar questions

Which part of the GC equipment does separation takes place?
Calculate volume and weight of sludge generated in thickener by chemical coagulation.Data given as:Wastewater flow: 10000 m3/dInlet concentration: 1100 mg/LFeCl3 added: 500 mg/LCaO added: 400 mg/LOverall particle removal efficiency: 80%Sludge’s specific gravity: 1.05Sludge’s moisture content: 95%Assume STANDARD chemical reactions and their product’s behavior as:FeCl3 + H2O → Fe(OH)3CaO + H2O → Ca(OH)2
TRUE OR FALSE __________ 11. The minimum number of centrifuge tubes in a centrifuge machine during its operation is one. __________ 12. Never place reagents directly onto the weighing pan of a balance, always use weighing paper, a beaker, or some other container. __________ 13. To transfer a solution, the stirring rod touches the delivery point of the reagent vessel and the wall of the receiving vessel. __________ 14. An open flame is the heat source for heating or evaporating flammable liquids. __________ 15. Most chemicals used in experiments can be discarded into the sink.
In measuring the surface tension of a liquid (drop weight method), 20 drops of the liquid (r=0.2cm) falling apart from the tip whose diameter is 0.4cm were found to weigh 0.95 gram. What is he surface tension of the liquid? Show complete solution, and round the final answer up to 4 decimal places.
Taylor was harvesting her beautiful, pure crystals via vacuum filtration from a methanol/water mixedsolvent system. She poured the solution containing her crystals into the Büchner funnel. Then sherinsed her flask with some warm methanol and poured that over the crystals resting in the Büchner…oops! Tell what happened and why
sketch a schematic showing how a liquid sample can be extracted from a liquid pipeline?
A chemistry graduate student is designing a pressure vessel for an experiment. The vessel will contain gases at pressures up to 70.0 MPa. The student's design calls for an observation port on the side of the vessel (picture). The bolts that hold the cover of this port onto the vessel can safely withstand a force of 2.40 MN. Calculate the maximum safe diameter w of the port. Round your answer to the nearest 0.1cm
what term describes the relationship of the axix of the 1/2" NPT pipe plug with the main axis of the bottom assembly?
The %purity of a powdered crude sample of Na2CO3 containing only inert impurities is to be determined by reacting 225.0 mg of the crude sample to 10.0 mL of 3.00 M HCl solution, and bubbling the resulting CO2(g) product in water that is at exactly 29 °C. After the reaction has completed, the level of the liquid inside the eudiometer rests 4.30 cm above the water level in the beaker. The graduation on the eudiometer indicates that the trapped gas is 44.37 mL. The experiment was done under a barometric pressure of 755.2 torr. a. How many moles of CO2 were collected? b. What is the percent purity of the sample? Round off to the nearest whole number
The %purity of a powdered crude sample of Na2CO3 containing only inert impurities is to be determined by reacting 225.0 mg of the crude sample to 10.0 mL of 3.00 M HCl solution, and bubbling the resulting CO2(g) product in water that is at exactly 29 °C. After the reaction has completed, the level of the liquid inside the eudiometer rests 4.30 cm above the water level in the beaker. The graduation on the eudiometer indicates that the trapped gas is 44.37 mL. The experiment was done under a barometric pressure of 755.2 torr. What CASE does this experiment satisfy?
Which of the following are safe and effective techniques for drying organic solids recovered from a filtration? (Choose all that apply). a. Spreading the solid evenly on a watch glass or aluminum weigh boat and placing it in an oven set at a temperature 20 °C below the substance's expected melting point. b. Placing it on top of a hotplate set on low. c. Leaving the solid on the funnel with the vacuum on for several minutes. d. Blowing on the solid.
1. Minimal OR Maximum 2. Impurities OR substances while Impurities OR substance remain… 3. Centrifuge OR Filter