Show the COMPLETE SOLUTIONS and DIAGRAM (T-8) (Cycle) including the switching of table and Interpolations/extrapolations: NO Calculator Technique and Applications. 1. A smaller power plant produces steam at 3 MPa, 600o C in the boiler. It keeps the condenser at 450 C by transfer of 10 MW out as heat transfer. The first turbine section expands to 500 kPa and then flow is reheated followed by the expansion in the low-pressure turbine. Find the reheat temperature so the turbine output is saturated vapor. For this reheat find the total turbine power output and the boiler heat transfer.

Show the COMPLETE SOLUTIONS and DIAGRAM (T-8) (Cycle) including the switching of table and Interpolations/extrapolations: NO Calculator Technique and Applications. 1. A smaller power plant produces steam at 3 MPa, 600o C in the boiler. It keeps the condenser at 450 C by transfer of 10 MW out as heat transfer. The first turbine section expands to 500 kPa and then flow is reheated followed by the expansion in the low-pressure turbine. Find the reheat temperature so the turbine output is saturated vapor. For this reheat find the total turbine power output and the boiler heat transfer.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

1. A reheat cycle with two stages of reheating is executed with steamexpanding initially from 90 bar and 530°C. The two reheaterpressures are 10 bar and 0.6 bar, and the steam leaves eachreheater at 480°C.Condensation occurs at 0.03 bar. Find the cycleefficiency.2. An ideal reheat turbine with one stage of reheat receives steam at8.0 MPa and 480°C. Reheat pressure is 0.83 MPa and exhaustpressure is 0.007MPa. The work is 1559 KJ/kg and thermalefficiency is 41%. Find the temperature of the steam leaving thereheater.
Show the COMPLETE SOLUTIONS and DIAGRAM (T-s) (Cycle) including the switching of table and interpolations/extrapolations: NOCalculator Technique and Applications. A smaller power plant produces steam at 3 MPa, 600°C in the boiler. It keeps the condenser at 45°C by transfer of 10 MW out as heat transfer. The first turbine section expands to 500 kPa and then flow is reheated followed by the expansion in the low-pressure turbine. Find the reheat temperature so the turbine output is saturated vapor. For this reheat find the total turbine power output and the boiler heat transfer.THE ANSWER MUST BE: 6487 kW ; 16 475 kW
PLEASE ANSWER LETTER D AND E WITH COMPLETE SOLUTION, THANK U 1. Steam is the working fluid in an ideal Rankine cycle. The saturated vapor enters the turbine at 8.0 MPa and saturated liquid exits the condenser at a pressure of 0.008 MPa. The net power output of the cycle is 100 MW. Determine for the cycle (a) the thermal efficiency, (b) the mass flow rate of the steam, in kg/h, (c) the rate of heat transfer, into the working fluid as it passes through the boiler, in MW, (d) the rate of heat transfer, from the condensing steam as it passes through the condenser, in MW, (e) the mass flow rate of the condenser cooling water, in kg/ h, if cooling water enters the condenser at 15 DEGREE CELCIUS and exits at 35 DEGREE CELCIUS.
Solve neatly and draw diagrams. write neatly An regenerative engine receives 68,000 kg/hr of steam having 1 open heater which receives 15,400 kg/h of Bled steam. If the condenser pressure is 0.008 MPa and the open heater pressure is 0.98 MPa find the enthalpy a) at the heater entrance, b) condenser entrance.
Need help with this engineering problem. Steam enters the turbine of a simple vapor power plant with a pressure of 12 MPa and a temperature of 500°C and expands adiabatically to condenser pressure, p. Saturated liquid exits the condenser at pressure p. The isentropic efficiency of both the turbine and the pump is 84%.For p = 100 kPa, determine: (a) the turbine exit quality, in percent.(b) the cycle thermal efficiency, in percent.
3. A 200 MW power plant operates on a simple Rankine cycle. Steam at 5.2 MPa, 400ºC expandsin a Rankine turbine to 0.036 MPa. Assume actual turbine with isentropic efficiency of 75 % forboth the compressor and expander. 3.1 Heat added in steam Generator , KW 3.2 Power loss at Turbine, KW 3.3 Actual thermal efficiency of the cycle 3.4 Mass of water in kilogram needed for an hour in the condenser if the changeof temperature for the water is 27ºF
Steam at 6.155MPa and 435degC enters the turbine of a power plant which operates on actual vaport power cycle. The pressure at the exit of the turbine is 418 kPa, and steam leaves the condenser as a saturated liquid at 62degC. The pressure is increased to 12.2 MPa accross the pump. The turbine and pump have isentropic efficiencies of 82% and 74% respectively. For this cycle, determine th: a. Wnet per unit mass of steam flow and the heat transfer to steam passing through the boiler (kj/kg)b. thermal efficiency (%) c. heat transfer to colling water passing the condenser (kj/kg of steam condensed)
1. Consider a steam power plant that operates on a simple ideal Rankine cycle and has a net power output of45 MW. Steam enters the turbine at 7 MPa and 500°C and iscooled in the condenser at a pressure of 10 kPa by runningcooling water from a lake through the tubes of the condenserat a rate of 2000 kg/s. Show the cycle on a T-s diagram withrespect to saturation lines, and determine (a) the thermal efficiency of the cycle, (b) the mass flow rate of the steam, and(c) the temperature rise of the cooling water. Answers:(a) 38.9 percent, (b) 36 kg/s, (c) 8.4°C 2. Consider a 210-MW steam power plant that operateson a simple ideal Rankine cycle. Steam enters the turbine at10 MPa and 500°C and is cooled in the condenser at a pressure of 10 kPa. Show the cycle on a T-s diagram with respectto saturation lines, and determine (a) the quality of the steamat the turbine exit, (b) the thermal efficiency of the cycle,and (c) the mass flow rate of the steam. Answers: (a) 0.793,(b) 40.2 percent, (c) 165…
A power plant operating in a Reheat Rankine Cycle produces steam at 3 MPa, 600oC in the boiler. It keeps the condenser at 45oC by transfer of 10 MW out as heat transfer. The first turbine section (high-pressure) expands to 500 kPa and then flow is reheated followed by the expansion in the low-pressure turbine. Provide a detailed solution. Avoid shortcuts. Determine the values of enthalpy for each state.
Refrigeration Cycle: A refrigerator operates on the ideal vapor-compression refrigeration cycle and use R-134a as the working fluid. The condenser operates 1.4 MPa and the evaporator at 0.140 MPa. (a) Show the cycle on a T-s diagram, indicating the enthalpies at the end of each process, with respect to saturation lines. For a mass flow rate of 0.100 kg/s, determine (b) the net power input to the compressor, in kW, (c) the heat rejection to the environment, in kW, (d) the heat rejection from the cold refrigerated space to the evaporator, in kW, and (e) the coefficient of performance. use the formula in the picture
Consider a water-ammonia binary vapor cycle consisting. In the steam cycle,superheated vapor enters the turbine at 7 MPa, 450oC, and saturated liquid exits thecondenser at 55oC. The heat rejected from the steam cycle is provided to the ammoniacycle, producing saturated vapor at 45oC, which enters the ammonia turbine.Saturated liquid leaves the ammonia condenser at 1 MPa. For a net power output of24 MW from the binary cycle, determine (c) the rate of heat input to the ammoniacycle, in MW, (d) the rate of heat addition to the binary cycle, in MW, and (e) thethermal efficiency of the binary vapor cycle.
A steam cycle operates between 150 bar, 1000 K, and 1 bar. Theturbine and feedpump are perfectly efficient, and, two open feedwaterheaters being used, the splits in the streams through the turbine into theheaters are optimal. Determine(a) The fraction of the total flow that must pass through eachfeedwater heater,(b) The thermal efficiency.Draw T-s and Schematic Diagram.