Stadia Tacheometric Survey Problem 3. In the figure, the difference in elevation between observed points A and B is 15 m and the horizontal distance between them is 35 m. With transit at Station O, additional information was obtained as shown in the table. Determine the stadia intervals at A and B. Assume K=100 and C = 0. Occupied O Station Observed A B B RR (m) 1.863 1.500 S ? ? A VCR 12° 10°

Stadia Tacheometric Survey Problem 3. In the figure, the difference in elevation between observed points A and B is 15 m and the horizontal distance between them is 35 m. With transit at Station O, additional information was obtained as shown in the table. Determine the stadia intervals at A and B. Assume K=100 and C = 0. Occupied O Station Observed A B B RR (m) 1.863 1.500 S ? ? A VCR 12° 10°

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Correct the survey data below for a closed traverse. LINE DISTANCE BEARING AB 495.85 m N 05°30’ E BC 850.62 m N 46°02’ E CD 855.45 m S 67°38’ E DE 1,020.87 m S 12°25’ E EF 1,117.26 m S 83°44’ W FA 660.08 m N 55°09’ W
The following data were obtained by stadia observation: vertical angle, +12deg 30 min; upper stadia hair reading and lower stadia hair readings, 4.500 and 3.250m, respectively. The rod reading was taken at 3.875m above the stadia point at A and the height of instrument above the instrument station, B, is 1.620m. If the stadia interval factor is 99.5 and the instrument constant is 0.381m, compute the horizontal distance between theinstrument stationand the stadia point. Compute also the difference in elevation between the two ground points.
I need Answer of A only A. A tachometric surveying was conducted to obtain some readings forinaccessible points, where it was found that the multiplying and additiveconstants are 98 and 0.1, respectively. The instrument was setup at point C and the readings listed in the table were taken while the staff was held vertically. Calculate the horizontal distance between BM and station D. Also, calculate the reduced level of station D. Figure 1 shows a schematic view of the site.
FUNDAMENTALS OF SURVEYING 1, FIELD 1.) A backsight reading of 2.73m is taken to a point A and subsequently a foresight reading of 1.35m is taken on point B from a level station established midway between the two points. a)What is the difference in elevation between points A and B? b) If the elevation of A is 386.70m above sea level, what is the elevation of B?
In a topographic survey undertaken by Karman Surv.Corp. before any leveling is conducted. The engineersusually check whether the engineers level is in perfectadjustment. A two peg test is used to check whether theline of sight is in perfect adjustment and the followingrod readings are taken, with instrument set up near A,backsight on A is 1.623 m. and foresight reading on B is2.875 m. with the instrument set up near B, backsight onB is 1.622 m. and foresight on A is 0.362 m. Compute the difference in elevation between Aand B. What should be the correct rod reading on A togive a level line of sight with the instrument stillset up at B? What should have been the reading on B with theinstrument at A to give a level line of sight?
A traverse was done by a group of civil engineering students. The folowing measurementswere recorded. Refers to the figure below.a. Calculate the azimuth and bearing of the traverse lines. b. Adjust the traverse by compass rule. c. Calculate the area enclosed by the traverse. Use DMD method. d. Calculate the coordinates of all stations if TP has N = 1230.014 and E = 9180.017Note: Tabulate your calculations.
A transit is set at point "P" with elevation = 96m, height of instrument = 1.2m, stadia interval factor = 100, stadia constant = 0.3. Find the elevation of points 1 and 2 and the distance to the points observed as per data below. Points Observed Rod Intercept True Azimuth Vertical Angle 1 1.056 352*12 +2°00' 1.260 56°16' -4°00' on 1.65m 2
Surveying Question: A three sided closed traverse returns to the same point. The details of the traverse are given in the attached image. The azimuth of AB is 118.34o. Find the corrected angles to the right, and the order and class of the survey. The given K values are: First order: 1.7" Second Order Class 1: 3" Second Order Class 2: 4.5" Third Order Class 1: 10" Third Order Class 2: 20"
A tachometric surveying was conducted to obtain some readings forinaccessible points, where it was found that the multiplying and additiveconstants are 98 and 0.1, respectively. The instrument was setup at point C and the readings listed in the table were taken while the staff was held vertically. Calculate the horizontal distance between BM and station D. Also, calculate the reduced level of station D. Figure 1 shows a schematic view of the site.
Following are the observations recorded using a total station between two points Aand B:The zenith angle is 82°32'20", the slope distance is 8335.26 ft. The height of theinstrument and rod recording r are equal. If the elevation of point A is 1431.31 ft.Determine the elevation of point B.
A transit with a stadia interval factor of 98.99 was set at C on the line between points A and B, the following stadia readings were observed. (draw the Instrument set up) *Inserted Photo* If the stadia constant is 0.29 m determine the following: Length of line AB (horizontal). ANSWER: ____________________ If the elevation at B is 782m what is the elevation at A. ANSWER: ___________________
A transit with a stadia interval factor of 99.89 was set at C on the line between points A and B, the following stadia readings were observed. (draw the Instrument set up) If the stadia constant is 0.31 m determine the following: Length of line AB (horizontal). ANSWER: ____________________ If the elevation at B is 752m what is the elevation at B. ANSWER: ___________________