State the disadvantages of hydraulic transmission systems.

Q: The coefficient of efficiencies between different transmission elements are not usually at the same…

A: The coefficient of efficiency (also termed as energy efficiency ratio) is defined as the ratio of…

Q: Select an appropriate clutch system to transmit power from the engine to the compressor of a car air…

A: The compressor used to air condition your car works in a similar way to the one in the refrigerator…

Q: With a neat sketch explain the types of Drives used in automobile.

A: There are different types of drives used in the automobiles  Front engine - Rear wheel drive Rear…

Q: Explain how drum brakes create a self-multiplyingbrake force

A: Given data : Brake force

Q: advantages of using electronic controls rather than relying on conventional hydraulic controls in a…

A: In modern vehicles mostly electronic controls are used rather than the conventional hydraulic…

Q: What are the advantages and disadvantages of conical clutches compared with plate friction clutches?

A: Cone clutch is a type of friction clutch is used to engage and disengage engine shaft to the…

Q: The cars like Padmini and ambassador have axleless transmission in the front wheels explain how the…

A: The car like Padmini and ambassador have 5 speed manual with an overdrive transmission system. The…

Q: Derive the expression for Frictional torque on cone clutch based on uniform pressure theory

A:

Q: To design a gearbox that will allow a motor to lift a 120lbf load 60ft vertically in 30 seconds…

A: A transmission is another name for a gear box. A set of gears and their case, most typically…

Q: and material, explain why V-belt

A: a      Diary or plain course comprise of a shaft or diary which pivots unreservedly in a…

Q: Why solenoid is used in almost all industrial applications, draw a schematic diagram…

A: Answer : Solenoid :- It is a hollow cylindrical coil of wire acting as a magnet while when current…

Q: 3. Critically discuss the relationship between Pascal’s law and displacement transmission

A: Pascal's law states that a change in pressure at any point in an enclosed fluid at rest is…

Q: Modern types of mechanical gearbox have efficiencies that depends on

A: We have to determine on what factor is the efficiency of the mechanical gearbox

Q: What is the extreme transmission angle values by using maxima and minima condition, of the…

A: The extreme transmission angle in the four-bar mechanism is given as : μmin=sin-1cos2θ2 here ,…

Q: Design the gearbox used in modern cars and also state its working principle.

A: Gearboxes are necessary in automobiles to provide a variety of speed ratios. These are generally…

Q: What is the effect of belt thickness and slip on speed ratio?

A:

Q: Explain the "Slip" and "Creep" phenomena that occur in a belt drive.

A:

Q: Torque =230 N-m

A: The torque for designing a rigid flange couple is given as,  T=250 N-mT=250×103 N-mm The number of…

Q: Write down the parameters considered in determining the basic dimensions of the friction clutch

A: Basic clutch design issues are presented, including friction elements during engagement, friction…

Q: Establish a formula for the frictional torque transmitted by a cone clutch

A: Concept: There are two theories to estimate the torque transmitted by the cone clutch:   1) Uniform…

Q: While discussing types of coil springs: Technician A says that linear-rate coil springs have equal…

A: Technician A:- Technician A is correct says that in case of linear-rated coil springs have equal…

Q: Define Braking loads

A: Braking load/force  is the  frictional force that cats tangentially  between the brake pads and…

Q: 15. If a hydraulic motor with a displacement of 1.65 in./rev receives fluid at 20 gal/min, what…

A: Soln :- displacement = 1.65 in^3/rev. Q =20 gal/min As we know Q = displacement × N 20 gal/min =…

Q: 1. Explain about open belt drives and cross belt drives 2 -Write the advantages, disadvantages and…

A:

Q: At what instance would you consider using a belt or chain drive system instead of a gear…

A:

Q: 2a-e. Outline five transmission problems its causes and their solutions.

A: A transmission is a mechanism that offers regulated power application in a power transmission…

Q: Overrunning clutches are capable of

A: Overrunning clutches are capable of

Q: Determine the Actual Torque Required, TA

A:

Q: Composition of manual transmission

A: Changing aesthetic sensibilities and a demand for high performance ushered in a development in…

Q: History of manual transmission

A: The first manual gearbox was created by Emile Levassor and Louis-Rene Panhard. The original…

Q: A clutch is a mechanical device which is used to connect or disconnect the source of power from the…

A:

Q: Base on your analysis, why the value of Belt Drive with V-Belt is having a lower coefficient…

A: In belt drive power transmission will take place by a meas of friction between belt and pulley…

Q: Q) Derive the expressions for the torque transmitting capacity of a single plate clutch by pressure

A: The answer is in the next step

Q: (a) (b)

A: The fluid power system can be classified into two types - the first one is a Hydraulic system and…

Q: The coefficient of efficiencies between different transmission elements are not usually at the sa…

A: Coefficient of efficiency

Q: Advantages and disadvantages of SS316 material for gearbox housing

A: Advantages and disadvantages of SS316 material for gearbox housing

Q: Which clutch would you use to connect two spindles with a 250 angle between them? Why you chose this…

A: To connect two spindles with a 250 angle between them, an electromagnetic clutch will be a better…

Q: What is the importance of studying on how to pull-out and mount manual transmission?

A: Manual transmission is a mechanism that enables a vehicle driver to choose the gear ratio of his…

Q: Q.3 Identify three types of Limited Slip Differentials and briefly explain how they work.

A: Given:- Limited slip differential   To find:- Types and explanation

Q: and cross

A:

Q: Explain the operation principle of a differential system and how a differential system relates to…

A: Given Differential system To find Operation principle of differential principle Differential system…

Q: Compare the features of chain drive with other drives

A: Chain drive is a method of transmitting mechanical power from one point to another. It is commonly…

Q: Discuss briefly the various types of belts used for the transmission of power.

A: Solution:

Applied Fluid Mechanics

A fluid is a substance that is continuously deformed by the application of shear stress. The rate of deformation of a fluid depends on its viscosity. The fluid tries to flow when it interacts with some other system.