3 Study figures 31-6 a & b in chapter 31 (page863) of your prescribed textbook, and drawseparation of compounds A and B on a TLCplate (clear labelling will be appreciated).A + BPackedcolumn@Detectorsignal(b)SampleMobile phase12TimeB14лиDetectorFigure 31-6 (a) Diagram showingthe separation of a mixture ofcomponents A and B by column clutionchromatography. (b) The detectorsignal at the various stages of clutionshown in (a).

Answered: Study figures 31-6 a & b in chapter 31…

Study figures 31-6 a & b in chapter 31 (page 863) of your prescribed textbook, and draw separation of compounds A and B on a TLC plate (clear labelling will be appreciated).

Principles of Instrumental Analysis

7th Edition

ISBN:9781305577213

Author:Douglas A. Skoog, F. James Holler, Stanley R. Crouch

Publisher:Douglas A. Skoog, F. James Holler, Stanley R. Crouch

Chapter30: Capillary Electrophoresis, Electrochromatography, And Field-flow Fractionation

Section: Chapter Questions

Problem 30.6QAP

See similar textbooks

Similar questions

A sample of steel (0.506 g) was digested in acid and the solution made up to 100 cm3 with deionised water. Aliquots (25.0 cm3) of this solution were transferred into two volumetric flasks (100 cm3) labelled A and B. Flask A was made up to volume with deionised water. To flask B was added 10.0 cm3 of a 260 ppm standard solution of Mn2+ which was then also made up to volume with deionised water. The following absorbance results were obtained: Solution A = 0.356, Solution B = 0.578. Use these results to calculate the percentage (% w/w) of manganese in the steel sample.
For Indirect Iodometric Analysis of Copper... ~0.0896g KIO3 necessary to consume 350mL of 0.1 M Na2S2O3, Na2S2O3 is stored in an amber glass bottle until ready for use. Primary Standard KIO3 has 2g of KI, 50mL of DI water, and 10 mL of 1.0M HCl is added then immediately titrated with Na2S2O3 until medium yellow or straw... then 5mL of starch indicator is added and titrated again until blue black color turns clear. Unknown CuO use 1.2G of Unknown, 20mL of HNO3 heated until sample dissolved, 25 mL of DI water added and boiled until clear light blue color, after cooling 1:1 NH3 added (~34.47 mL of NH4OH reagent) until permanent deep blue color amine complex, 2g of NH4HF2 added and swirled until dissolved, 3 g of KI is added then titrated immediately with Na2S2O3 until brown color of iodide is nearly gone (brown milk color), 2 g of KSCN and 3 mL of starch indicator is then added with titration continuing until disappearance of new blue black color. 1. Na2CO3 is often added to thiosulfate…
For Indirect Iodometric Analysis of Copper... ~0.0896g KIO3 necessary to consume 350mL of 0.1 M Na2S2O3, Na2S2O3 is stored in an amber glass bottle until ready for use. Primary Standard KIO3 has 2g of KI, 50mL of DI water, and 10 mL of 1.0M HCl is added then immediately titrated with Na2S2O3 until medium yellow or straw... then 5mL of starch indicator is added and titrated again until blue black color turns clear. Unknown CuO use 1.2G of Unknown, 20mL of HNO3 heated until sample dissolved, 25 mL of DI water added and boiled until clear light blue color, after cooling 1:1 NH3 added (~34.47 mL of NH4OH reagent) until permanent deep blue color amine complex, 2g of NH4HF2 added and swirled until dissolved, 3 g of KI is added then titrated immediately with Na2S2O3 until brown color of iodide is nearly gone (brown milk color), 2 g of KSCN and 3 mL of starch indicator is then added with titration continuing until disappearance of new blue black color. 4. Why is the starch indicator solution…
Procedure: analytically transfer between 0.4053g of iron(III) chloride hexahydrate, FeCl 3•6 H2O (M = 270.2957g•mol-1), and dissolve in 5.5 mL distilled, deionized water. Support the tube on a stir plate and over a 15-minute period add, using the 10mL burette, 5mL of a nominal 600mM solution of 2,4 pentandione in methanol under constant stirring. To the resulting solution, add via a 10mL burette 3mL of a nominal 450mM sodium acetate solution stirring constantly. At this point, a red crystalline solid should begin to precipitate. Transfer and support the reaction vessel in the hot water bath and once the reaction mixture has reached a stable temperature in the desired range, maintain the reaction mixture at this temperature, under constant stirring, for a 15-minute period Initial weight of iron(III) chloride hexahydrate: 0.4053g The final weight of the reaction tris(acetylacetonate)iron(III): 19.6 mg 3. What is the charge on the metal in the starting material for your synthesized…
It has been notice that adulteration of palm oil with carcinogenic dyes are on rise. Use knowledge in analytical process to systematically outline a protocol to follow to process adulterated palm oil to gain quantitative and qualitative information spectroscopically about any added toxic dye. Explain also the basis of your protocol of choice.
In coulometric karl Fisher water analysis, 25.0 mL of pure “dry” methanol required 4.23 C to generate enough I2 to react with residual H2O in methanol. A suspension of 0.8476 g of finely ground polymeric material in 25.0 mL of the same “dry” methanol required 63.16 C. Find the weight percent of water in the polymer.
1. Discuss briefly the specifications and test parameters for system suitability for HPLC analysis.
Six iron tablets containing FeSO4.7H2O were dissolved in 100-ml of 0.1M HNO3 with gentle heating. All of the Fe2+ is converted to Fe3+ by the strong oxidizing conditions. After the solution had cooled to room temperature , 2.5-ml of 35wt% NH4OH was added. The precipitate Fe2O3-xH2O that was filtered weighed 0.345g. Thermogravimetric analysis of the crude product showed a 10.5% weight loss . A. How many waters of hydration were in the precipitate B. How much iron is present in each tablet
A 5.00-mL sample of blood was treated with trichloroacetic acid to precipitate proteins. After centrifugation, the resulting solution was brought to pH 3 and extracted with two 5-mL portions of methyl isobutyl ketone containing the lead-complexing agent APCD. The extract was aspirated directly into an air/acetylene flame and yielded an absorbance of 0.527 at 283.3 nm. Five-milliliter aliquots of standard solutions containing 0.400 and 0.600 ppm of lead were treated in the same way and yielded absorbances of 0.396 and 0.599. Find the concentration of lead in the sample in ppm assuming that Beer’s law is followed.
Explain the meaning of the advantages of coulometry * No need to prepare, standardize, or store standard solutions. * Can prepare unstable reagents in situ (original place) since they react almost as soon as they are generated - e.g., C12, Br2 * Straightforward to generate tiny quantities of reagent with good accuracy since it is easy to control current and time electronically. * A single coulometric titration apparatus can be used for redox, acid/base, precipitation, complexometric, etc., titrations.
A 50.00mL sample with BaCl2 was diluted to 650 mL. Aliquots of 100.00 mL of this solution were analysed using Mohr and Volhard methods. The following data were obtained. Volhard method: Volume of AgNO3 = 100mL; Volume of KSCN = 18.25mL Mohr Method: volume of AgNO3: sample = 27.80mL (blank) = 0.30mLWhat is the %BaCl2 using Mohr and Volhard Method. Concentration of KSCN: 0.04000M Concentration of AgNO3: 0.03000M
Note: Express % strength with 4 decimal places. For ratio strength, state the volume only% Astelin nasal spray contains 0.1% azelastine hydrochloride and 125 mcg/mL of benzalkonium chloride as a preservative. A container is capable of delivering 200 metered sprays of 0.137 mL each. The percent concentration of benzalkonium chloride in the preparation is _______%, which is equivalent to a ratio strength of 1 in _____ w/v.