Suppose that a ductile iron (100-70-03, air quenched) has a tensile strength of 800 MPa. What diameter impression would you expect the 3000 kg load to produce with the 10mm diameter
Q: e yield strength for an alloy that has an average grain diameter of 4.1 × 10-2 mm is 131 MPa. At a…
A: Given:σ1=131 MPaD1=4.1*10-2 mmD2=7.6*10-3 mmσ2=246 MPaσ=236 MPa
Q: 2. Could the maximum shear stress theory and the Von Mises theory be used for copper and aluminum…
A: The maximum shear stress theory and the von mises theory are suitable for ductile material Since…
Q: 57 kN axial force acts on the part shaped by the machining method made of xCy steel material. The…
A:
Q: 6. What is yield stress, how is it determined for metallic materials. Give the reason behind yield…
A: Yield stress is defined as the minimum stress at which a material will undergo strain without any…
Q: A 30 cm long, 12 mm diameter carbon steel rod was subjected to 15.5 kN of tension. Calculate: (a)…
A: Given Applied load = 15.5 kN Length = 30 cm Diameter = 12 mm To find Stress Strain Change in…
Q: The yield region for steel that has a normal grain diameter of 2.4x10-2 mm is 260 MPa. At a grain…
A:
Q: From the following figure shows the tensile stress- strain curve for a plain-carbon steel. What is…
A:
Q: A 10 mm diameter Brinell hardness indenter produced an indentation 2.5 mm in diameter in a steel…
A: Brinell Hardness Number (HBN/BHN) is the numerical value given to the hardness of given material.
Q: With respect to the S-N diagram shown below, answer the following questions: (a) for Gray cast iron,…
A: Part (a) Mark the value of 20,000 psi on the vertical axis. Move to the right and mark a point at…
Q: a. What is the Brinell hardness number (HB) for 1020 Steel that has been annealed at 785 "C? (Check…
A:
Q: der an S-590 alloy component as shown in following figure that is subjected to a stress of 200 MPa…
A:
Q: What properties does an involute have? Please answer this based on the notations in the figure.
A: Although a variety of profiles can be employed to create gears, the involute curve is the most…
Q: A component is subjected to a maximum cyclic stress of 750 MPa and a minimum of 70 MPa. The steel…
A: INTRODUCTION : Fatigue failure occurs when a recurrent or cyclic load causes cracks to develop and…
Q: Compute the tensile strength, yield strength and ductility (%EL) of a cylindrical copper rod if it…
A: Given data: - The initial diameter of rod is di = 15.2 mm. The final diameter of the rod is df…
Q: Question 1) For a 1095 HR steel, estimate (a) The rotating-beam endurance limit (in kpsi) at 10°…
A:
Q: If you could produce AISI 1020 steel with a grain size of 50 nm, what would be the expected yield…
A: Permissible stress is stress which produces due to pressure or forces which does not exceed the…
Q: he critical resolved shear stress for copper is 0.48 MPa. Determine the maximum possible yield…
A:
Q: If the required yield strength of a steel is 150 ksi, could SAE 1141 be used? Why?
A: Given :- Required yield strength of steel = 150 ksi To Find:- Suitable condition and SAE number…
Q: 1. Give 4 examples of nonferro material? 2. Explain creep with example 3. Explain Bending Stress…
A: Hi and thanks for the questions. Since you have asked multiple questions, we will solve the first…
Q: n application requires ultimate tensile strength and yield strength of a steel at 110 ksi and 91…
A: I. Can SAE 1040 steel be selected for this application? Yes, It can be selected. Because the…
Q: 7.32 (a) What is the approximate ductility (%EL) of a brass that has a yield strength of 345 MPa…
A: (a) A yield strength of 345 MPa (50,000 psi) for brass corresponds to 20 %CW. A brass that has been…
Q: 3. Labeled S-N curve for fatigue, fatigue crack growth curve and creep curve for a metal.
A: for solution refer below images.
Q: Define the term Percent Elongation?
A: Whenever a specimen is subjected to an external load it deforms. Due to this deformation the…
Q: A rod specimen of ductile cast iron was tested in a torsion-testing machine. The rod diameter was 14…
A:
Q: Task #7 The yield strength of mild steel with an average grain size of 0.05 mm is 20,000 psi. The…
A: Given Case 1 Average grain size = 0.05 mm Yield strength = 20000 psi Case 2 Grain size = 0.007 mm…
Q: ate tensile strengths and the same percentage elongation, yet they are not the same steels. What are…
A: given: Materials 605M36 and 655M31 have the same yield and ultimate tensile strengths and the same…
Q: 13) Hot rolling of mild steel is carried out a. At recrystallization temperature b. Between…
A: Answer is (c) Above recrystallization temperature.
Q: A sheet of a 70% Cu-30% Zn alloy is cold-rolled 20% to a thickness of 3.0mm. The sheet is then…
A:
Q: A cylindrical rod of non cold-worked brass having an initial diameter of 6.4 mm (0.25 in.) is to be…
A: Given:do=6.4 mmdi=5.1 mm
Q: Determine the yield strength sy and the ultimate strength su of the A36 steel either from Materials…
A: To find: For A36 Steel Yield strength sy = ? Ultimate strength su = ?
Q: Given a 1050 HR steel, estimate Sut = 630 MPa (a) the rotating-beam endurance limit at 106 cycles.…
A:
Q: Two copper samples with grain size (d) of 0.016 mm and 0.007 mm have the yield stresses of 125 MPa…
A: Given: The diameter of grain size from sample 1 is, d1=0.016 mm. The diameter of the grain size…
Q: A ¼ inch diameter steel rod is to carry an axial load of 2000 lbs. If the yield strength is 38 ksi,…
A: Given : Axial load = 2000 lbs Diameter of steel rod = ¼ inch The yield strength of steel = 38 ksi
Q: a component is made of 6061 T6 aluminum sheet LT. A axial tensile stress of 50 ksi is applied at…
A: The deformation of a material in response to a tensile, compressive, or torsional force is…
Q: Determine whether the first part of statement will INCREASE, DECREASE or HAVE NO EFFECT in the…
A: 1. If there is an increase in application of stress then the presence of dislocation will INCREASE…
Q: 3) (10) A 10-mm-diameter tungsten carbide sphere creates a 4.26-mm- diameter impression under a…
A: Given: The diameter of the tungsten carbide sphere is d=4.26 mm, The diameter of the tungsten…
Q: A material has a stress-strain behavior shown in the Figure below. What is the material strength at…
A: Toughness: The energy stored by the material per unit volume up to the point of rupture is known as…
Q: 5 Hot rolling of mild steel is carried out. a. Between recrystallization temperature b. Above…
A: Correct option: b. Above recrystallization temperature
Q: what is fracture stress,ductility and modulus of resilience for 304 Stainless Steel and 6061-T6…
A: Fracture stress is also known as the breaking strength of the material at which the material fails…
Q: b) A cylindrical shaft with 380 mm length, having a diameter of 10.0 mm, is to be subjected to a…
A:
Q: What is the maximum value of KIc as per LEFM that can be determined from experiments on a 20 mm…
A: Givent=20mmσy=500MPaE=210GPaμ=0.3
Q: Metal Working: What process will result in a Martensite microstructure? List the reasons why this…
A: Martensite structure in the steel is a very important structure and can be formed by continuous…
Q: Consider a single crystal of BCC iron oriented such that tensile stress is applied along a [010]…
A: According to the given information we have BCC single crystal A third typical packing structure in…
Q: Using various tables, determine the specific strength (yield strength-to-density ratio) in unit of…
A:
Q: Question-1 A 70% Cu-30% Zn brass wire is cold-drawn 20 percent to a diameter of 2.80 mm. The wire is…
A:
Trending now
This is a popular solution!
Step by step
Solved in 3 steps with 3 images
- Indicate which microstructures will appear after each induction hardening process step: Options: ( martensite, tempered martensite, bainite, pearlite, austenite) a. tempering. b. Quenching c. Induction heatingQ1: 1.5 in diameter steel part is quenched in oil with no agitation. (H=0.20). If we use a 4340; 4140; 8640; 5140; 1040 steel, what would be the hardness number at the center of the part? Q2: Determine the best quenching medium to produce a minimum hardness of HRC 40 at the center of a 3.75 cm diameter 4320 steel bar.In a eutectoid steel the following microstructures are required for different application. Suggest cooling rate and sequences to achieve them. a) 50% Pearlite and 50% Bainite b) 50% Bainite and 50% Martensite c)100% fine Pearlite d) 100% Martensite e) 50% Peralite and 50% Martensite
- Show microstructure of 8620 steel before homogenized annealing and microstructure after annealing.Which one of the following statements best describes the heat treatment type applied to SAE1050 OQT 1300 steel? a) The material is annealed at 1300 oF b) The material is normalized at 1300 oF and quenched in water c) The material is quenched in oil and tempered at 1300 oF d) The material is quenched in water and tempered at 1300 oF1-Compact Graphite cast iron was obtained from fast cooling rates.? T F 2-Strength and ductility of nodular iron approximately the same under tension and compressive loads.? T F 3-The grey should be heated to 700 oC for 30 hours to obtain malleable iron? T F 4-The carbon in CGI alloys is neither flakes nor cementite? T F 5-Exhaust manifold manufactured from white cast iron.? T F 6-The reduced section length of the tensile specimen should be at least four times the diameter.? T F 7-Tangent modulus is taken as the slope of the stress–strain curve at yield stress? T…
- Hardness of steel greatly improves with a. Cyaniding b. Tempering c. Annealing d. Normalizing11.14), specify the na- nure of the final microstructure (in terms of microconstituents present and approximate percentages of each) of a small specimen that has been subjected to the following time-temperature treatments. In each case assume that the specimen begins at 760°C (1400°F) and that it has been held at this temperature long enough to have achieved a complete and homogeneous austenitic structure. (a) Cool rapidly to 700°C (1290°F), hold for 104 s, then quench to room temperature. (b) Reheat the specimen in part a to 700°C (1290°F) for 20 h. (c) Rapidly cool to 600°C (1110°F), hold for 4 s, rapidly cool to 450°C (840°F), hold for 10 s, then quench to room temperature. (d) Cool rapidly to 400°C (750°F), hold for 2 s, then quench to room temperature. (e) Cool rapidly to 400°C (750°F), hold for 20 s, then quench to room temperature. (f) Cool rapidly to 400°C (750°F), hold for 200 s, then quench to room temperature. Rapidly cool to 575°C (1065°F), hold for 20 s, rapidly cool to…70) The lowest melting point for steel to be taught in the iron carbon phase diagram...A) eutectoidB) monocriticalC) eutecticD) subeutectoidE) peritectic 71) Which is not a surface texture parameter?A) roughnessB) cutting lengthC) arrayD) wavyE) hardness 72) Where do negative ions go in the electrochemical apparatus?A) to solutionB) to the cathodeC) first to the cathode, then to the anodeD) first to the anode, then to the cathodeE) anode
- How would the following heat treatment be conducted, quoting approximates temperatures, cooling rate and microstructure of:(i) Normalizing of a plain carbon steel containing 0.8 wt % C, (ii) Quenching of a plain carbon steel containing 0.8 wt % C in water (iii) Quenching of a plain carbon steel containing 0.8 wt % C in oil (iv) full annealing of a plain carbon steel containing 0.8 % C.Copper and copper alloys as specified by the Copper Development Association (CDA) and are designated as C00001 thru C99999 in the Unified Numbering System (UNS). True False An alloy steel designated as AISI 4130 WQT 700 means: chromium-molybdenum alloy steel containing .30% carbon in solution, that is through heat treated and water quenched. True False An AISI 4340 alloy steel contains .43 percent or 43 points of the element carbon in solution. True False Chemicals from which the commercially important plastic resins are derived are themselves derived from natural products that are quite plentiful; these raw materials include coal, water, limestone, sulfur, salt, and petroleum. True False There are two (2) types of polymerization; addition or linear and cross-linked or condensation. Addition polymers are thermoplastics and cross-linked polymers are thermosetting materials. True FalseKindly help me with all answers. I will hit 2 likes??? Which of the following hot rolled steels would have the most ferrite in its microstructure? a) C1020 b) C1040 c) C1060 d) C1080 Which of the following hot rolled steels would have the most pearlite in its microstructure? a) C1020 b) C1040 c) C1060 d) C1080 What does rapid quenching do to the hardness and ductility of a plain high carbon steel, compared to slow cooling? a) hardness and ductility both increase b) hardness and ductility both decrease c) hardness decreases and ductility increases d) hardness increases and ductility decreases Tempering of a plain carbon steel is defined as a) rapid quenching of the annealed metal b) cold working of the annealed metal c) reheating the austenitized and quenched metal to an intermediate temperature d) reheating the annealed metal to an intermediate temperature How does the tempering process effect hardness and ductility of the metal? a) hardness and ductility both increase b) hardness…