Task 3: A hollow aluminum alloy 6061-T6 shaft of outer radius c = 40 mm, inner radius b = 30 mm, and length L=1.2 m is fixed at one end and subjected to a torque T at the other end If the shearing stress is limited to max = 140 MPa, determine (a) the largest value of the torque; (b) the corresponding minimum value of shear stress; (c) the angle of twist that will create a shear stress min = 100 MPa on the inner surface.

Task 3: A hollow aluminum alloy 6061-T6 shaft of outer radius c = 40 mm, inner radius b = 30 mm, and length L=1.2 m is fixed at one end and subjected to a torque T at the other end If the shearing stress is limited to max = 140 MPa, determine (a) the largest value of the torque; (b) the corresponding minimum value of shear stress; (c) the angle of twist that will create a shear stress min = 100 MPa on the inner surface.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter3: Torsion

Section: Chapter Questions

Problem 3.7.10P: What is the maximum power that can be delivered by a hollow propeller shaft (outside diameter 50 mm,...

See similar textbooks

Similar questions

A shaft with a hollow cross section is subjected to torque of magnitude T = 5.5 kN-m. If the outer diameter of the shaft is 0.1 m and its wall thickness is 10 mm, what would be the minimum diameter of a solid steel shaft needed if it would be subjected to the maximum shear stress of the hollow shaft?
The motor shown in Fig. P6-47 develops 100 hp at a speed of 360 rpm. Gears A and B deliver 40 hp and 60 hp, respectively, to operating units in a factory. If the maximum shearing stress in the shafts must be limited to 12 ksi, determine a. The minimum satisfactory diameter for the motor shaft. b. The minimum satisfactory diameter for the power shaft. (1 hp=745,7 watts); (1 ksi=6,89 MPa); (1 ft=0,30 m)
Problem 1: A circular shaft with a diameter of 100 mm and a length of 2 meters is subjected to a torsional moment of 500 Nm. The shaft is made of a material with a shear modulus of 80 GPa. Determine the maximum shear stress and the angle of twist along the length of the shaft. Problem 2: A solid circular shaft of length 3 meters is made of a material with a shear modulus of 60 GPa. The shaft has a diameter of 80 mm and is subjected to a torque of 600 Nm. Due to manufacturing constraints, the maximum allowable shear stress for the material is 60 MPa. Determine if the shaft design is safe and, if not, suggest an alternative design to meet the given constraints.
Torsion in circular shafts From the figure as shown, the maximum shearing stress is 30 MPa and the angle of twist is 1.25°. Determine the maximum permissible torque? Use G = 80 GPa.
Bearing stress 4. Please provide proper discussion and illustration also complete solution and clear solution please thank you Determine the length of a square key to be used for a 3.73 kW, 1800 rpm electric motor if the motor shaft diameter is 35 mm and the width of the key is approximately one-fourth of the shaft diameter. The allowable shearing stress on the key is 2.45 MPa
A hollow brass alloy shaft with an outside radius of 50-mm and a wall thickness of 10-mm is subjected to a torque of T = 5.5 kN-m. Determine the minimum required diameter in mm of a solid steel shaft for which the maximum shear stress is the same?
Steel shaft can be produced as solid body or circular tube with circular tube. The shaft must bear a torque of 1200 Nm. Since the shear strength for the shaft material is 40 MPa, the maximum allowable unit torsion angle of the bar is 0.75 ^ 0 / m and the shear modulus of steel is G = 78 GPa;a) Find the required diameter d0 for a solid circle shaft.b) Find the required outside diameter d2 for a ring-section shaft whose thickness is one tenth of the outer diameter.c) Find the diameter ratio (d2 / d0 ratio) and weight ratio for ring cross section and solid section shafts
Calculate the maximum permissible torque on a hollow shaft if the maximum allowable shearing stress is 83 MPa. D=75mm and d=60mm. A)4788 Nm B)4316 Nm C)4059 Nm D)4532 Nm
Two designs for a shaft are being considered. Both have an outside diameter of 70 m and are 900 mm long. One is solid but the other is hollow with an internal diameter of 50 mm. Both are made from steel (G=120 GPa). Compare the torsional shear stress, angle of twist of the two designs if they are subjected to a torque of 796 N. m.
Gear B, shown in Figure Q4, supplies 15 kW of power, while gears A , C and D withdraw 6 kW, 4 kW and 5 kW, respectively. If the shaft is made of steel with the allowable shear stress of ?????? = 75 MPa, and the relative angle of twist between any two gears cannot exceed 0.05 rad, determine the required minimum diameter ? of the shaft to the nearest millimeter. The shaft is rotating at 600 rpm.
A 12.6 inches long key is to be used on a 210 hp, 1200 rpm, slip ring induction motor. The key is 1 in wide and has a depth of 3/4 in. The shaft diameter is 3 7/8 inches. The maximum running torque is 200% of the full-load torque. A. Determine the maximum compressive (crushing) stress of the key, in psi. B. Determine the maximum direct shearing stress on the shaft, considering the effect of the keyway, in psi.
according to Maximum Shear Stress theory ,Calculate the factor of safety of the shaft When it is subjected to an end thrust producing stress of 90 MPa and the maximum shearing stress on the surface arising from torsion is 60 MPa.The yield point of the material in simple tension was found to be 300 MPa.