The 12" piston diameter is fitted into the cylinder shown in fig. A 0.3 lbm liquid-vapor mixture of refrigerant Tetrafluoroethane gas at -20 ° F , the quality of this mixture is 70 %,is filled into the cylinder . The piston inside the cylinder is compressed by a spring of 25 lbf/in. The system is subjected to a process so that the volume of the gas is increased by 60%. Determine approximately the final temperature and enthalpy of this gas . Spring F-K.X AWA D-12"

The 12" piston diameter is fitted into the cylinder shown in fig. A 0.3 lbm liquid-vapor mixture of refrigerant Tetrafluoroethane gas at -20 ° F , the quality of this mixture is 70 %,is filled into the cylinder . The piston inside the cylinder is compressed by a spring of 25 lbf/in. The system is subjected to a process so that the volume of the gas is increased by 60%. Determine approximately the final temperature and enthalpy of this gas . Spring F-K.X AWA D-12"

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

how would you find the conditions of Saturated vapor at 1 MPa on a Mollier Chart
A conduit connects two receptacle of different size. A valve is used at eachend which can be opened or closed. The first receptacle contains 300 litersof air at 4,200 kPa, 82C. The second receptacle contains air at 75kPa, 9C.Calculate the volume of the second receptacle if after the valve wasopened and the properties of the mixture were 2400kPa for the pressure,and 52C for the temperature.
A 1500L tank contains benzene at a pressure of 400kPag and a temperature of 320K. Later, because of leak, it was found that the gauge pressure has dropped to 320kPag, and the temperature has decreased to 300K, determine the amount of benzene that has leaked out.
If 10 kg of ice at 0C is added to 2 kg of steam at 100C, the temperature of resulting mixture is
CO2 gas enters the pipe at a flow rate of 2 kg / s, 3 MPa pressure and 500 K temperature. While the CO2 pipe type is flowing, it is cooled down at constant pressure and its temperature drops to 450 K at the pipe outlet.Volumetric flow of CO2 at the pipe inlet,Using the generalized compressibility diagram, find
The piston in a car engine compresses a mixture of gasoline vapour and air from 700ml to 100ml during its compression stroke. Before the compression stroke, the mixture had a pressure of 75 kPa and a temperature of 120celcius. What is the pressure of the cylinder after the compression stroke if the temperature of the gas rises to 200celcius? Express your answer in MPa with two significant digits.
A conduit connects two receptacle of different size. A valve is used at eachend which can be opened or closed. The first receptacle contains 300 liters of air at 4,200 kPa, 82C. The second receptacle contains air at 75kPa, 9C. Calculate the volume of the second receptacle if after the valve was opened and the properties of the mixture were 2400kPa for the pressure, and 52C for the temperature.
Q5/ 400-L rigid tank contains 5kg of water at 200kPa. Determine (a) the temperature, (b) the total enthalpy, and (c) the mass of each phase of water?
Determine the volume flow rate and the density of carbon dioxide at the inlet and the volume flow rate at the exit of the pipe using (a) the ideal-gas equation and (b) the generalized compressibility chart. Also, determine (c) the error involved in the first case.
In a piston-cylinder arrangement, an initial temperature of 250 °C and 1.4 MPapressure contains 4 kg of water vapor. Then the mass of water vapor at constant pressure3/4 is cooled until condensation.a) Show this process in the T-v diagram by taking into account the saturation lines.b) Calculate the change in volume.c) Calculate the final temperature.urgenttttttt please
Contruct a P-v and T-v diagram for water and refrugerant-134a
50 liters at 40 °C temperature and 200 kPa pressure initially in a piston cylinder Assemblyliquid water is available. Then, until the water evaporates completely at constant pressureheatsa. What is the mass of water?b. Calculate the final temperature of the water.c. Calculate the total enthalpy change.d. Taking into account the phase change process saturation lines in the T-v diagramyour show.