The band wrench of Fig. an oil filter from a car. (The filter acts as if it were a wheel with a resisting torque of 40 lb ft.) Determine the mini- mum coefficient of friction between the band and the filter that will prevent slippage. The weight of the handle can be neglected. is used to unscrew 40 Ib-ft 2.5 in. -2 in. 7.5 in.

The band wrench of Fig. an oil filter from a car. (The filter acts as if it were a wheel with a resisting torque of 40 lb ft.) Determine the mini- mum coefficient of friction between the band and the filter that will prevent slippage. The weight of the handle can be neglected. is used to unscrew 40 Ib-ft 2.5 in. -2 in. 7.5 in.

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.81P: Calculate the horizontal force P required to push the 85-lb lawn mower at constant speed. The center...

See similar textbooks

Similar questions

The coeffient of static friction between the uniform bar AB of weight W and the ground is 0.45. Find the smallest angle and the corresponding force P that would initiate simultaneous tipping and sliding of the bar.
The block of weight W is pulled by the force P inclined at the angle to the horizontal. Find the smallest force P and the corresponding angle that would cause impending sliding of the block. The angle of static friction between the block and the ground is s.
The test specimen AB is placed in the grip of a tension-testing machine and secured with a wedge. The coefficient of static friction at both surfaces of the specimen is s. If the wedge angle is =18, determine the smallest s for which the grip is self-locking (no slipping takes place regardless of the magnitude of the force P). Neglect the weight of the wedge.
The square-threaded screw with a pitch of 10 mm and a mean radius of 18 mm drives a gear that has a mean radius of 75 mm. The static and kinetic coefficients of friction between the gear and the screw are 0.12 and 0.06, respectively. The input torque applied to the screw is C0=10Nm. Assuming constant speed operation, determine the output torque C1 acting on the gear.
Calculate the horizontal force P required to push the 85-lb lawn mower at constant speed. The center of gravity of the mower is at G, and the coefficients of rolling resistance are 0.12 for the front wheels and 0.18 for the rear wheels.
Draw the FBD of the entire frame, assuming that friction and the weights of the members are negligible. How many unknowns appear on this FBD?
Q) The static friction coefficient between the box stationary on the inclined surface and the surface is gs. If you know the mass of the box is 25 kg, and 4, = 0.35, what force T is required to start the box -y 40T sliding up the surface? Then discuss your results Fig. Q.
High-strength bolts are used in the construction of many steel structures. For a 1-in.-nominal-diameter bolt, the required minimum bolt tension is 51 kips. Assuming the coefficient of friction to be 0.30, determine the required couple that should be applied to the bolt and nut. The mean diameter of the thread is 0.94 in., and the lead is 0.125 in. Neglect friction between the nut and washer, and assume the bolt to be square-threaded.
A ladder, 8 m long and having a mass of 25 kg, rests on a horizontal floor and is supported by a vertical wall. The ladder is inclined 62°, as shown, and starts to slip when a person having a mass of 73 kg has climbed halfway up it. The coefficient of friction at the wall is 0.20. Assume the weight of the ladder to be concentrated at its midpoint. Calculate the coefficient of friction at the floor. - Draw a free-body diagram - Solve most simple way
Q3/ A screw-jack is used to lft a load of 4 kN. The screw of the screw-jack is square threaded with two threads to 1 cm. If the co-efficient of friction between the nut and screw is 0,095 and outer diameter of screw s 6 cm, find the force required atthe end of the handle of length 50 cm to ift the load. (20 M)
2 A ladder 5 m long and weighing 260 N is placed against a vertical wall at an inclination of 30 ^ 0 with wall. A wan weighing 780 N climbs the ladder. When he is at a distance of 1.64 m along the ladder from lower all contact surfaces? end, the ladder slips. What is the coefficient of friction assuming it to be same for
PROBLEM: To prevent a box from sliding down an inclined plane, student A pushes on the box in the direction parallel to the incline, just hard enough to hold the box stationary. In an identical situation, student B pushes on the box horizontally. If the weight of the box w= 20.0 N, the angle made by the incline with the horizontal θ=25o, and the coefficient of static friction µs=0.16, who has the easier job?