The bar supported by a pin at A and a cable at B carries a load of 260 N at C. Neglecting the weight of the bar, a.) Determine the normal force 3 m from A. b.) Determine the shear force 3 m from A. c.) Determine the bending moment 3 m from A d.) Determine the torsion 3 m from A 60% BE 4 m 12 5 m 260 N

The bar supported by a pin at A and a cable at B carries a load of 260 N at C. Neglecting the weight of the bar, a.) Determine the normal force 3 m from A. b.) Determine the shear force 3 m from A. c.) Determine the bending moment 3 m from A d.) Determine the torsion 3 m from A 60% BE 4 m 12 5 m 260 N

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A 90-lb load is suspended from the hook shown . If theload is supported by two cables and a spring having a stiffnessk = 500 lb/ft, determine the force in the cables and the stretch of thespring for equilibrium. Cable AD lies in the x–y plane and cable AClies in the x–z plane.
A cable was used to dry the clothes from wet laundry by hanging as shown below. The clothes are placed such that approximately loads the cable by a uniform q(x) = q0. If l (small letter L) = 10 m, hA = 5 m, and hB = 4 m. Compute the maximum force in the cable for its minimum distance to the group by 3 m. q0 (kN/m) 12.213
1. The transmission tower OA is being hoisted into position by the cables AB and AC. The resultant of the cable tensions P and Q, along with the 2400-lb weight of the tower, is a force R acting at point O. Determine P, Q, and R.\ 2.
2.4. Two cables are tied together at C and loaded as shown. Knowing that P= 360N,Determine the tension in cable BC and AC. 1 Free-body Diagram only
The 6-m pole ABC is acted upon by a 455-N force as shown. The pole is held by a ball-and-socket joint at A and by two cables BD and BE. For a =3 m, determine the tension in each cable and the reaction at A.
q0 (kN/m) = 20.627 A cable was used to dry the clothes from wet laundry by hanging as shown below. The clothes are placed such that it approximately loads the cable by a uniform q(x) = q0. If l = 10 m, hA = 5 m, and hB = 4 m, compute the maximum force in the cable for its minimum distance to the ground by 3 m.
The boom supports the two vertical loads. Neglect the size of the collars at D and B and the thickness of the boom, and compute the horizontal and vertical components of force at the pin A and the force in cable CB. SetF1 = 800 N and F2 = 350 N.
A cable is attached to the 20 kg plate B, passes over a fixed peg at C, and is attached to the block at A. Using the coefficients of static friction shown, determine the smallest mass of block A so that it will prevent sliding motion of B down the plane.
Determine the force P on the cable if the spring is compressed 0.5 in. when the mechanism is in the position shown. The spring has a stiffness of k = 800 lb/ft.
The overhead electric hoist Crides along a track on the horizontal beam . AB. In addition to the 500-kN vertical force carried by the hoist, the beam also supports the three vertical forces shown. (a) If x = 5 m, determine the resultant of the four forces carried by the beam. (b) Determine the distance x for which the resultant of the four forceswould act at the center of the span AB.
The frame ABCD is hinged at A and D and is supported by a cable that passes through a ring at B and is attached to hooks at G and H. Knowing that the tension in the cable is 450 N, determine the moments about the diagonal AD of the force exerted on the frame by portion BH and portion BG of the cable.
A cable ABCD is pulled at end E by a force P (Figure P6.12). The cable is supported at point D by a rigid member DF. Compute the force P that produces a sag of 2 m at points B and C. The horizontal reaction at support F is zero. Compute the vertical reaction at F.