The clutch, or friction, disc is connected to the

Q: yebolt supports the four forc es) is a direct pull of 3 kN in t

A: GIVEN:

Q: Drive Shaft in SINUMERIK

A: A drive shaft is a vehicle shaft that transmits power from the transmission to the wheels. The…

Q: Differentiate between single acting and double acting cylinders.

A: Differentiate between Single Acting & Double Acting Cylinder :

Q: What causes suction of fluid into the gear pump? a. when pressure drops during engagement of teeth…

A: a. when pressure drops during engagement of teeth at the suction sideb. when pressure increases…

Q: The ratio of tension on the tight side to that of the slack ride in a flat belt drive is

A: Given, find the ratio of tension on the tight side to that of the slack ride in a flat belt drive

Q: DIOCK orce experienced by both the

A:

Q: choose true or false : -The speed of the sprocket reduces as the chain pitch increases for a given…

A: The speed of the sprocket reduces as the chain pitch increases for a given number of teeth.

Q: The high tension side of belt is known as tight side Select one: True

A: Given: Belt pulley system

Q: three-cylinder in-line engine

A:

Q: This is called the... baggage hold propeller cabin cockpit

A: Baggage hold is the system of aircraft which is used to hold baggage or to store the baggage during…

Q: When the clutch is disengauged, where does the power flow stop? Select one: a. the transmission…

A: Clutch : Clutch is a mechanical device which is used to engage and disengage the power at the will…

Q: When the load acting on the power transmission shaft is high, then the -------------- bearings are…

A: When the load acting on the power transmission shaft is high, then the -------------- bearings are…

Q: A clutch has an outside diameter of 8 in and inside diameter of 4 in. An axial force of 500 lb is…

A:

Q: __________ is connection between the bit and the surface, where the torque is generated. Which helps…

A:

Q: With a neat sketch explain the Analysis of simple hydraulic Jack.

A: Jacks are pieces of industrial heavy equipment that raise or move heavy loads by multiplying force.…

Q: The factor of safety for the piston rod is

A: Given data; diameter (d) =20mmlength (l)=700 mmforce=10 kNYOUNG MODULUS=200 GPa acc. to question we…

Q: How is the air exhausted at the back of the piston when the piston retracts?

A: By employing a single acting air cylinder in the application rather than a more traditional…

Q: In the absence of collar friction, the power screw described in the previous two problems is…

A: FALSE

Q: Tighten the cylinder head nut in the order prescribed by----- -----, using the appropriate torque by…

A:

Q: Design a piston for use in automobile engines (piston ring, pin, skirt).

A:

Q: kw per cylir of the crank and combu

A:

Q: describe type and properties of spring used in impact of jet apparatus.

A: Solution:

Q: 1000 rpm

A: 5)  104.72rad/s 6)  16.67s 7) 91.89N/m

Q: А В C

A:

Q: The amount of force generated by an air bearing decreases when?

A: The amount of force generated by an air bearing decrease when

Q: For the given statements: Mating spur gear teeth is an e pair A revolute inint is an examp

A: Because the upper pair has a line or point contact whereas the lower pair has a surface or area…

Q: Respond with TRUE if the symbof of the valve shown below is drawn cortectly A 工 R Select one: O True…

A: True or False  The given symbol

Q: Determine the maximum, minimum and average pressure in a plate clutch

A: Given data;  Axial force(W)=4kn=4×103 NInside radius (r2)=50mmoutside radius(r1)=100mm Assume…

Q: The bolt size of cylinder head in a reciprocating compressor is a. M16

A: The bold size of the cylinder head in a reciprocating engine M16 option (a) is correct.

Q: /5 --- A computer cannot "boot" if it does not have the

A: An operating system is the system software that handles the software and hardware resources and…

Q: In the operation of some automatic transmissions both blank and blank overrunning clutches are used…

A: In the operation of some automatic transmissions both blank and blank overrunning clutches are used…

Q: maximum output power from the Pelton wheel

A: Given: For a pelton wheel with a given water jet velocity, the maximum output power from the Pelton…

Q: In most of internal combustion engines, crankshaft bearing is  Select the correct answer below: A.…

A: Concept: Hydrodynamic bearing: 1) In this bearing, two rubbing surfaces of bearing are separated by…

Q: d to design a spring in train,

A: Answer- Steel alloy & All the Units are correctly used.

Q: Determine whether the mechanism below is mandatory movement. body hydraulic cylinder

A: Solution:

Q: rom the ov when the in Car Cand theo

A:

Q: The advantage of the optimized size of the piston is that it requires less material so the cost of…

A: Given Piston To find Piston geometry

Q: Where is the rod end of the cylinder?

A: Given: To identify the rod end of cylinder.

Q: The surface of the pressure plate contacts the __ .a. transmission main shaftb. throwout bearingc.…

A: The driven friction disc is held between the pressure plate and the flywheel by a clamping force.…

Q: of motion for the syste

A:

Q: problem

A: Given:S=6000lb/in2=864000lb/ft2W=490 ln/ft2A=2 in2=.0139 ft2L=1000ft…

Q: What type of caps are used to hold the crankshaft in place once it’s installed in the block?

A: Crankshaft is a shaft used in engine to convert a linear motion of piston to a rotational motion. It…

Q: When the clutch is disengaged, the power flow stops at the

A: When the clutch is disengaged, the power flow stops at the

Q: Draw FBD of Bicycle axle (Thru axle)

A: To find :- Fbd of axle

Q: "his shaft is subje - 10,000 in-lb., fom and F - 20,000 lb approsch, deter

A:

Clutches, Brakes, Couplings, and Flywheels

The clutch is described as a machine element used to connect or disconnect two shafts together to transmit torque or power. The clutch works on the principles of friction. The clutch is commonly used in automobiles to transfer power from the driving shaft to the driven shaft.