Engineering

Mechanical EngineeringQ&A LibraryThe diameter of two pulleys are (0.3m)and (0.2m), center distance (1m).if we use open belt drive. Determine: 1- the length of V-belt (2ß = 60°). 2- the contact angle between belt and smaller pulley. 3- the horse power, if the smaller pulley turn with speed (400r.p.m) and the tension force in tight side (T1=900N), coefficient of friction ų=0.3 4- the speed of large pulley.Start your trial now! First week only $4.99!*arrow_forward*

Question

PROBLEM

The diameter of two pulleys are (0.3m)and (0.2m),

center distance (1m).if we use open belt drive.

Determine:

1- the length of V-belt (2ß = 60°).

2- the contact angle between belt and smaller pulley.

3- the horse power, if the smaller pulley turn with

speed (400r.p.m) and the tension force in

tight side (T1=900N), coefficient of friction ų=0.3

4- the speed of large pulley.

Tagged in

Engineering

Mechanical Engineering

Find answers to questions asked by students like you.

Q: 2. Explain the differences between an engine that operates on a thermal cycle and an engine that ope...

A: an ic engine is defined as a thermodynamic cycle engine consist of various processes that involve th...

Q: Need solution to both questions.

A: Hello. Since you have posted multiple questions and not specified which question needs to be solved,...

Q: below this circle is structure

A: Hello. Since your question has multiple sub-parts, we will solve the first three sub-parts for you. ...

Q: The two steel shafts in Fig. have the same diameter and weigh 100 lb each. Neglecting friction at co...

A: Consider the diagram shown below for the given system,

Q: You are standing outside. The wind speed suddenly increases. Your rate of heat loss by convection wi...

A: Let us consider that the effective area responsible for heat transfer is A and the temperature diffe...

Q: 2. For the image, label the region indicated by the arrow and the expected mechanical response for t...

A: In the given image, there are two regions white region and the dark region. First define the dark re...

Q: A Rankine Cycle operates between high and low temperature reservoirs at 1500oC and 25oC respectively...

A: Given data: For the maximum theoretical efficiency it is assumed that the total heat added to the c...

Q: 12.5. The cantilever beam of Figure P12.5 of length L and flexural rigidity El has an initial deflec...

A: Write the expression of beam deflection. Write the expression of the deflection at z = L. Understa...

Q: Explain the relationship between STRUCTURE/ PROPERTIES/ PROCESSING/ PERFORMANCE of a polymer which i...

A: Polymers are found in every aspect of life now a days and it is almost impossible to imagine life wi...

Q: I downloaded this question multiple times but I had no answer. I need 6 I have to get answer for it

A: The properties required for mechanical design are: Strength- The strength is measured by the maximu...

Q: winding drum that operates the elevator. If the elevator has a mass of 900 kg, the counterweight C h...

A: Given data: Torque, M = 6kN.M Mass of the elevator, mE = 900 kg Counterweight C, mC = 200 kg Mass of...

Q: a) Why the knowledge of Mechanics of machines is important? And write the classification ofmechanics...

A: Hello. Since you have posted multiple questions and not specified which question needs to be solved,...

Q: One of the following is a surface force Select one: a. pressure b. electrostatic magnetic C. d. grav...

A: Pressure –it is defined as the ratio of the force and the area. Which means its values can be depend...

Q: M Whwel = 50 kg (k.) wheel =0.15 m 2) The 50-kg wheel is connected to a 10-kg block as shown. The bl...

A: Given data:

Q: 3-94. Replace the parallel force system acting on the plate by a resultant force and specify its loc...

A: Click to see the answer

Q: Throttling Valve Which of the following statements about flow through an insulated throttling valve ...

A: A.. The enthalpy increases- inaccurate statement, The upstream and downstream enthalpies are equal –...

Q: In fully developed laminar flow in a circular pipe, the velocity at R/2 (midway between the wall sur...

A: Given : The velocity at r from the center line, V r =13 m/s here, r=R/2

Q: A piston–cylinder device contains 0.6 kg of steam at 200oC and 0.5 MPa. Steam is cooled at constant ...

A: Since, we are entitled to solve upto only three sub-parts. I am solving the first three parts for Yo...

Q: A loading condition is shown below. The wires AB and CD both have yield strength (Sy) of 71 ksi, dia...

A: Draw the free-body diagram of the system.

Q: The velocity components of an incompressible, two-dimensional velocity field are given by the equati...

A: Writing the continuity equation for the two-dimensional velocity field for an incompressible flow fi...

Q: Based on the phase diagrams, estimate the solubilities of Ni, Zn, Al, Sn, andBe in copper at room te...

A: To estimate the solubility, the use of the atom size difference approach, we will determine the perc...

Q: Identify the shaft diameter as datum feature A and the right end as datum feature B. Ø.500 .002

A: Datum are the physical boundaries used to establish a simulated datum from a specified datum feature...

Q: can you please do this for do

A: considering x -x-axis as reference plane

Q: The smallest particle of an element which can be broken into and still retain the properties of that...

A: an element is that substance that made of a single type of atoms. Most of the elements exist as mono...

Q: 3-85. The belt passing over the pulley is subjected to forces F, and F, each having a magnitude of 4...

A: Let the forces F(1) acts at B and F(2) at C as shown below – Writing the coordinates of points at w...

Q: 15-6. A train consists of a 50-Mg engine and three cars, each increase its speed uniformly to 40 km/...

A: Given data: Mass of engine = 50 Mg Mass of each car = 30 Mg Velocity,( vx)2 = 40 km/h Time = 80 s

Q: A handheld bicycle pump can be used as an atomizer to generate a fine mist of paint or pesticide by ...

A: Given data: The density of the air can be calculated using the ideal gas equation as shown below,

Q: What is spin in gyroscopic motion?

A: Consider a disc rotating with angular velocity ωs as shown in the figure below,

Q: P3-7. specify its coordinates r and y where it acts on the r-y plane. determine the resultant force ...

A: Solution : Let FR is the resultant force acting on the given force system. Let (x,y) are the coordi...

Q: To design a piston with lower pressure, should you increase or decrease its area? Why? Two containe...

A: Hello. Since you have posted multiple questions and not specified which question needs to be solved,...

Q: Specify a copper alloy that requires at least 50% elongation and at least 300 MPa tensile strength.

A: The stress-strain curve for a copper alloy (Brass) is given as under:

Q: Water enters a centrifugal pump axially at atmospheric pressure at a rate of 0.10 m3/s and at a velo...

A: Given data as per question Rate of water entering = 0.10 m3/s Velocity = 6 m/s Density of water = 10...

Q: 19–43. The mass center of the 3-lb ball has a velocity of (vG)ı = 6 ft/s when it strikes the end of ...

A: Write the expression of mass moment of inertia. Write the expression of angular velocity.

Q: 19-51. The solid ball of mass m is dropped with a velocity v onto the edge of the rough step. If it ...

A: The weight is a non-impulsive force, thus its angular moment is conserved about point A. Thus, the f...

Q: The shown spool has a mass of 100 kg and radius of gyration of 0.3 m. For P = 70 N and µ, = Hk = 0.2...

A: Given data: Consider the free body diagram of the spool as shown below, Here, Fr is the friction f...

Q: The structure of a football goal is shown in the figure below. The bending motion of the structure c...

A: When the soccer ball hits the crossbar then apply the conservation of linear momentum, Here, vo is ...

Q: a: What is the magnitude of the first principal stress? b: What is the magnitude of the second princ...

A: Consider the tensile stresses to be positive and the compressive stresses to be negative. Write the ...

Q: F3-34. Replace the loading by an equivalent resultant force and specify where the resultant's line o...

A: Click to see the answer

Q: Having a hard time figuring these out.

A: Hello. Since your question has multiple sub-parts, we will solve the first three sub-parts for you. ...

Q: 11. The shown 2-D plate is in contact with a heat source at its upper edge, which supplies heat at a...

A: The energy in the form of heat is transferred from one body to another due to the temperature gradie...

Q: (1)Discuss about different point between Linear impulse and Linear momentum plz!!!! (2)Discuss abo...

A: (1) The difference between linear impulse and Linear momentum is given as (a) The product of mass an...

Q: 3-43. If F = 450 N, determine the magnitude of the moment produced by this force about the x axis. 1...

A: The Cartesian force vector can be calculated as

Q: Air at T = 25 C° and p = 1 atm flows past a long flat plate, at the end of which is placed a narrow ...

A: Write the given information. Write the properties of air at 25°C and 1 atm pressure.

Q: can you plase do this for me

A: Water flow rate = 58 litre/s = 58×10-3 m3 /s Diameter of pipe = 150 mm = 0.150 m Surface roughness v...

Q: Please help me get this orthographical plate drawing right!

A: Hello. Since your question has multiple sub-parts, we will solve the first three sub-parts for you. ...

Q: This is a dynamics question. Hint: don't worry about calculating the angle theta, just calculate the...

A: Given data as per question Velocity of bullet ,v = 800 m/s Mass of bullet,mb = 10 g Mass of disk,m...

Q: A force of P = 500 N is applied to the 80-kg cart. Determine the reactions at both the wheels at A a...

A: Given data as per question force of P = 500 N MASS = 80 kg

Q: Air at 100 kPa, 300 K enters an ideal Otto cycle. The initial volume is 500 cm3. The compression rat...

A: Given data as per question Air pressure at inlet= 100 kPa Temperature at entry = 300 K Initial volum...

Q: Thermodynamics Question: An insulated rigid tank is divided into two equal parts by a partition. Ini...

A: Given : The pressure at one side , P1 = 800 kPa The temperature at one side, T1 = 50°C Solution: F...

Q: PLEASE ANSWER QUICKLY

A: Given data: Consider the diagram shown below for the given hydraulic press. Point C is the critica...