Question

Transcribed Image Text:The drawing illustrates an overhead view of a door and its axis of rotation. The axis is perpendicular to the screen. There are four forces acting on the door, and they have the same magnitude. Rank the torque r that each force produces, largest to smallest.
Axis of
Rotation
Door
(Overhead View)
F4
F2
F1
F3
T2, T3 and T4 (a two-way tie), T1
Т4, Тз, Т2, T1
T3, T2, T1 and T4 (a two-way tie)
T1, Т4, Тз, Т2
Т2, Т4, Тз, Т1
Expert Solution

This question has been solved!
Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.
This is a popular solution
Trending nowThis is a popular solution!
Step by stepSolved in 2 steps with 2 images

Knowledge Booster
Similar questions
- Two blocks are placed at the ends of a horizontal massless board, as in the drawing. The board is kept from rotating and rests on a support that serves as an axis of rotation. The block on the right has a mass of 2.4 kg. Determine the magnitude of the angular acceleration when the system is allowed to rotate. 12 kg 0.60 m Axis Support 1.4 m Magnitude a of the angular acceleration =arrow_forward12.0 N 30.0% b 10.0 N 9.00 N The figure shows one cylinder inside another. The inner cylinder has a radius of a = 0.5 m and a mass of 2 kg. The outer cylinder has a radius b = 1.5 m and a mass of 12 kg. On the system act 4 forces. Those shown in figure 2 and a friction force. If the magnitude of the frictional torque is 1.75 mN. Determine: a. The net torque vector on the system. (Magnitude and direction) b. The total moment of inertia of the systemarrow_forwardCan you show me how to solve this?arrow_forward
- To study torque experimentally, you apply a force to a beam. One end of the beam is attached to a pivot that allows the beam to rotate freely. The pivot is taken as the origin or your coordinate system. You apply a force of F = Fx i + Fy j + Fz k at a point r = rx i + ry j + rz k on the beam. Part a) Calculate the magnitude of the torque, in newton meters, when the components of the position and force vectors have the values rx = 3.71 m, ry = 0.075 m, rz = 0.085 m, Fx = 1.2 N, Fy = -7.6 N, Fz = 1.2 N. Part b) If the moment of inertia of the beam with respect to the pivot is I = 72 kg˙m^2, calculate the magnitude of the angular acceleration of the beam about the pivot, in radians per second squared.arrow_forwardEXERCISE HINTS: GETTING STARTED I'M STUCK! A man ties one end of a strong rope 7.68 m long to the bumper of his truck, 0.534 m from the ground, and the other end to a vertical tree trunk at a height of 3.86 m. He uses the truck to create a tension of 7.73 x 10 N in the rope. Compute the magnitude of the torque on the tree due to the tension in the rope, with the base of the tree acting as the reference point. N. marrow_forwardA uniformly dense rod with a length of 4 m and a mass of 6 kg is free to rotate around a frictionless axle through the center of the rod. Three forces are acting on the rod as shown in the figure below. 2 m 0.8 m 15 N 4 N 10 N 2 m 30° N What is the net torque (in Nm) acting on the rod? 0.665arrow_forward
- F₁ (= W mg 0 P= AF. f.y Axis The ladder in the picture has a mass of 30 kilograms and a length 3 meters. What is the normal force pushing the ladder up from the floor? FN = N X Assume that the ladder's weight is evenly distributed, so it can be treated as a single force through the middle. If the ladder is at a 56° angle from the ground, what is the torque exerted by the weight (using the floor as the pivot point)? N-m The torque from the ladder must be balanced by the torque caused by the normal force on the wall. Calculate this force. F₁ = N The normal force from the wall must be balanced by the friction force from the floor. Determine the minimum coefficient of friction to keep the ladder from slipping.arrow_forwardYou are installing a new spark plug in your car, and the manual specifies that it be tightened to a torque that has a magnitude of 55N·m. Using the data in the figure, determine the magnitude F of the force that you must exert on the wrench.arrow_forwardThe body in the figure is pivoted at O, and two forces act on it as shown. If r₁ = 2.15 m, r2 = 3.74 m, F₁ = 3.80 N, F₂ = 3.37 N, 0₁ = 65.0°, and 02 = 59.0%, what is the net torque about the pivot? Number i Unitsarrow_forward
- A pipe system consists of three pipes with lengths L1 = 1.95 m, L2 = 0.500 m, and L3 = 2.90 m. A plumber pulls on the end of the pipe system, at the point P, with a force Fp = -23.0 Ni+ 42.0 Nj + 32.0 Nk. Po What is the torque 7 due to about the origin? Enter your expression using ijk unit vector notation. N-marrow_forwardThe fishing pole in the figure below makes an angle of 20.0° with the horizontal. What is the magnitude of the torque exerted by the fish about an axis perpendicular to the page and passing through the angler's hand if the fish pulls on the fishing line with a force F = 125 N at an angle 37.0° below the horizontal? The force is applied at a point L = 1.86 m from the angler's hands. N⚫m ·L. 20.0° -1 20.0° 37.0° Additional Materials iarrow_forward
arrow_back_ios
arrow_forward_ios