The hydraulic pump on this forklift can pump fluid at a maximum pressure of 1500 psi (pounds per square inch). If it has to lift a load of 5.0 tons using only one ram, then the diameter of the piston ram must be how many inches big? Round to 2 significant digits.

The hydraulic pump on this forklift can pump fluid at a maximum pressure of 1500 psi (pounds per square inch). If it has to lift a load of 5.0 tons using only one ram, then the diameter of the piston ram must be how many inches big? Round to 2 significant digits.

Name: The hydraulic pump on this forklift can pump fluid at a maximumpressu
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: The hydraulic pump on this forklift can pump fluid at a maximumpressure of 1500 psi (pounds per square inch). If it has to lift a load of5.0 tons using only one ram, then the diameter of the piston ram must behow many inches big? Round to 2 signific

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.35P: The weight of the cylindrical tank is negligible in comparison to the weight of water it contains...

See similar textbooks

Similar questions

The weight of the cylindrical tank is negligible in comparison to the weight of water it contains (water weighs 62.4lb/ft3). The coefficient of static friction between the tank and the horizontal surface is s. (a) Assuming a full tank, find the smallest force P required to tip the tank, and the smallest s that would allow tipping to take place. (b) If the force P = 200 lb initiates tipping, determine the depth of water in the tank.
A hydraulic lift is to be used to lift a 5000-lb weight by putting a weight of 50 lb on a piston with a diameter of 0.50 ft. Determine the diameter of the piston on which the weight is to be placed.
The round handle of a faucet is affixed to a shaft that lets a valve to be open and closed every time the round handle is rotated. Give the radius of the handle if the shaft has a diameter of 1 cm and the MA of the machine is 8.
Q6: A hydraulic lift is to be used to lift a 2500 kg weight by putting a weight of 25 kg on a piston with a diameter of 10 cm. Determine the diameter of the piston on which the weight is to be placed.
An oil drum of 500 mm diameter and 1.5 long is to be rolled across a footstep of 100 mm high. Find the minimum push required at the top of the drum. Take density of the oil as 1 kg/litre. Neglect weight of the drum. [Ans. 1444.5 N]
Given that the weight density of water is 9810 N/m3, calculate the fluid force (in Newtons) on a rectangular 1.1m 2.7m flat plate submerged horizontally in water at a depth of 4m. Give your answer correct to two decimal places without the units. Round your answer to 2 decimal places.
15- What will be the diameter (in mm) of a water droplet, the pressure inside which is 0.00221 N/cm2 greater than the outside pressure? (Take surface tension as 0.075 N/m)
A cubical tank is filled with 2m of oil having specific gravity of 0.80. Find the force acting on the side of the tank when the acceleration is 5m/s2 vertically downward. Answer: 15.39 KN
A 10000 litre water tank is placed on a building roof and filled to capacity. The empty tank has a mass of 550kg. It is supported on 4 feet, each of which is a 300 x 300 mm steel plate. What is the pressure exerted by each plate, in Pa? (Round your answer to 2 significant figures)
Given that the weight density of water is 9810 N/m3, calculate the fluid force (in Newtons) on a rectangular 1.6m cross times 2m flat plate submerged horizontally in water at a depth of 4m. Give your answer correct to two decimal places without the units. Round your answer to 2 decimal places.
A gas under a pressure of 1 MPa absolute has a specific weight of 99 N/m^3. What is the value of R for the gas if T = 60°C?
A hydraulic cylinder filled with water has an inside diameter of 1.0 in and a length of 2.0 ft. How many pounds of force must be applied to a piston at the end of the cylinder to compress the water by 0.1 in? Take the bulk modulus of water to be K=312,000 psi.