The impact wrench consists of a slender 1-kg rod AB which is 580 mm long, and cylindrical end weights at A and B that cach have a diameter of 20 mm and a mass of 1 kg. This asse mbly is free to turn about the handle and socket, which are attached to the lug nut on the wheel of a car. If the rod AB is given an angular velocity of 4 rad/s and it strikes the bracket C on the handle without rebounding, determine the ungular impulse imparted to the lug nut.

The impact wrench consists of a slender 1-kg rod AB which is 580 mm long, and cylindrical end weights at A and B that cach have a diameter of 20 mm and a mass of 1 kg. This asse mbly is free to turn about the handle and socket, which are attached to the lug nut on the wheel of a car. If the rod AB is given an angular velocity of 4 rad/s and it strikes the bracket C on the handle without rebounding, determine the ungular impulse imparted to the lug nut.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The speed of the pickup truck’s engine is controlled by the Porter governor with 4 arms of equal length, and pivot on the axis of rotation. Each ball has a mass of 4 kg and the mass of the central load on the sleeve is 20 kg. The radius of rotation of the ball is 150 mm when the governor begins to lift, and 200 mm when the governor is at maximum speed. The initial angular speed of the engine’s crank is 14 rad/s, and it has reached a maximum speed at an acceleration of 0.4 rad/s2 after 5 seconds.a) If the speed of the crank of an engine is equal to the speed of its governor, calculate the angle between the upper arm and axis of rotation (?) when the governor starts to lift and when it is at maximum speed.b) Prove that the length of the governor’s arms is equal
The slotted circular disk whose mass is 4.9 kg has a radius of gyration about O of 230 mm. The disk carries the four steel balls, each of mass 0.17 kg and located as shown, and rotates freely about a vertical axis through O with an angular speed of 164 rev/min. Each of the small balls is held in place by a latching device not shown. If the balls are released while the disk is rotating and come to rest relative to the disk at the outer ends of the slots, compute the new angular speed N of the disk. Also find the magnitude |ΔE| of the energy loss due to the impact of the balls with the ends of the slots. Neglect the diameter of the balls and discuss this approximation.
The speed of the pickup truck’s engine is controlled by the Porter governor with4 arms of equal length, and pivot on the axis of rotation. Each ball has a massof 4 kg and the mass of the central load on the sleeve is 20 kg. The radius ofrotation of the ball is 150 mm when the governor begins to lift, and 200 mm whenthe governor is at maximum speed. The initial angular speed of the engine’scrank is 14 rad/s, and it has reached a maximum speed at an acceleration of 0.4rad/s2 after 5 seconds. 2.1. If the speed of the crank of an engine is equal to the speed of its governor,calculate the angle between the upper arm and axis of rotation (?) when thegovernor starts to lift and when it is at maximum speed.(11)2.2. Prove that the length of the governor’s arms is equal.
The thin 12 kg bar has an angular velocity in a clockwise direction ω = 1.5 rad/s when in position shown. Determine its angular acceleration and the normal reactions of the smooth surface A and B at that time. i = (1/12) M . L² for a homogeneous thin bar of mass M and length L.
The 30-kg turbine disk has a centroidal radius of gyration of 175 mm and is rotating clockwise at a constant rate of 60 rpm when a small blade of weight 0.5 N at point A becomes loose and is thrown off. Neglecting friction, determine the change in the angular velocity of the turbine disk after it has rotated through (a ) 90°, (b ) 270°.
The 31-kg reel is mounted on the 16-kg cart. Part A: If the cable wrapped around the inner hub of the reel is subjected to a force of P=50N, determine the velocity of the cart when t = 4.2 s. The radius of gyration of the reel about its center of mass O is kO=250mm. Neglect the size of the small wheels. Part B: Determine the angular velocity of the reel when t = 4.2 s.
Each of the two links has a mass of 2 kg and a centroidal radius of gyration of 60mm. The slider at B has a mass of 3 kg and moves freely in the vertical guide. The springhas a stiffness of 6 kN/m. If a constant torque M = 20 N∙m is applied to link OA throughits shaft at O starting from the rest position at θ = 45°, determine the angular velocity ofOA when θ = 0.
The 153-kg wheel has a radius of gyration about its center of mass O of kO = 283 mm. If it rotates counterclockwise at an angular speed of 1431 rev/min and the tension force applied to the braking band at A is TA = 1771N,a) Determine the angular acceleration, in rad/s2, so that the wheel comes to rest in 67.6 revolutions after TA and TB are applied.
The 5 kg thin disk shown rotates with a constant angular velocity about the shaft CD such that w1=5 rad/s. It also rotates about its own axis at A such that 2 rad/s and 4 rad/s at the instant shown. Considering only the mass of the disk, determine the reaction forces at the bearings C and D
The 25-kg cylinder A is free to slide along rod BC. When the cylinder is at x=0, the 46-kg circular disk D is rotating with an angular velocity of 4.8 rad/s. (Figure 1) If the cylinder is given a slight push, determine the angular velocity of the disk when the cylinder strikes B at x=600mm. Neglect the mass of the brackets and the smooth rod.
Each of the gears A and B has a mass of 2.4 kg and a radius of gyration of 60 mm, while gear C has a mass of 12 kg and a radius of gyration of 150 mm. A couple M of constant magnitude 10 N.m is applied to gear C determine a ) the number of revolutions of gear C required for its angular velocity to increase from 100 to 450 rpm, (b) the corresponding tangential force acting on gear A.
The 2-lb gear A is constrained to roll on the fixed gear B but is free to rotate about axle AD. Axle AD has a length of 20 in., a negligible weight, and is connected by a clevis to the vertical shaft DE that rotates as shown with a constant angular velocity w1. Assuming that gear A can be approximated by a thin disk with a radius of 4 in., determine the largest allowable value of w1 if gear A is not to lose contact with gear B.