Answered: The maximum gauge pressure in a…

The maximum gauge pressure in a hydraulic lift is 18 atm. What is the largest size vehicle (kg) it can lift if the diameter of the output line is 26 cm ? 1.0atm 1.013×10 Pa

Glencoe Physics: Principles and Problems, Student Edition

1st Edition

ISBN:9780078807213

Author:Paul W. Zitzewitz

Publisher:Paul W. Zitzewitz

Chapter13: State Of Matter

Section13.3: Fluids At Rest And In Motion

Problem 36SSC

See similar textbooks

Related questions

Q: The maximum gauge pressure in a hydraulic lift is 16.9 atm . 1 atm = 1.013 × 105 N/m². Part A What…

A: Given data The pressure in atm is given as P = 16.9 atm. 1 atm = 1.013 x 105 N/m2. The diameter of…

Q: What is the gauge pressure of water at a depth of 15 m below the surface of a freshwater lake?…

A: Gauge pressure (pg) is the pressure of a system above atmospheric pressure. pg = p - pa = hρg where,…

Q: Problem: Determine the pressure in kPa at the following points: a) Point 1 b) Point 23 c) Point A…

Q: The small piston of a hydraulic lift (see figure below) has a cross-sectional area of 2.70 cm2, and…

Q: The maximum gauge pressure in a hydraulic lift is 17 atm. What is the largest size vehicle (kg) it…

Q: You fill a 7.0 x 10-3 m3 bucket with water that flows from a pipe of radius 1.30 cm. If it takes…

A: given: volume of bucket=7*10-3 m3 radius of pipe=1.30cm time it takes to fill the tank=48 secs…

Q: Hi please help: the large piston of a hydraulic lift has a cross-sectional area A1= 367 cm^2 and…

A: Write a given values of this question. A1=367cm2=367×10-4mA2=8.9cm2=8.9×10-4mW=64kN=64×103N

Q: Water is flowing in a pipe with radius of 25.4 cm at velocity of 5 m/s. The viscosity of water is…

A: Reynolds number is the measure of type of flow. Reynolds number gives the information about the…

Q: The large piston of a hydraulic lift had a cross-sectional area 60 times mc ross-sectional area.…

A: Suppose a hydraulic lift having a large & small cross-sectional area (A2) & (A1)…

Q: A piece of wood is 0.600 m long, 0.250 m wide, and 0.080 m thick. Its density is 700 kg/m3. What…

A: The buoyant force can be expressed as FB=ρwgVl+ρwgVb

Q: The hydraulic lift's small piston with an area of 30 m^2 is subjected to a force of 100 N. To have…

A: Data provided: Area of small piston (A1) = 30 m2 Force on small piston (F1) = 100 N Force on large…

Q: A hydraulic lift has two pistons: a small one of cross-sectional area 5.00 cm- and a large one of…

A: Given: area of small piston, a = 5 cm2 area of large piston, A = 300 cm2 mass on large piston, M =…

Q: Water pressure acting on sunk plane at depth is 4×10⁶Pa. What is the magnitude of the force in kN…

A: Pressure, Area,

Q: (10.14) The maximum gauge pressure in a hydraulic lift is 17.0 atm. What is the largest-size vehicle…

Q: A hydraulic lift consist of two pistons that connect to each other by an in-compressible fluid. If…

A: 4.42 kg of mass can be raised by the given force

Q: A cargo ship of mass 90000 metric tonnes is floating in the Great Lakes. The Great Lakes are fresh…

A: (a) The weight of water displaced is equal to the buoyant force. The buoyant force be defined as,…

Q: The hydraulic lift's small piston with an area of 30 m^2 is subjected to a force of 100 N. To have…

Q: A hydraulic cylinder lifts a car (F2) delivering a force of 15000 N. The diameter of the small…

Q: The hydraulic oil in a car lift has a density of 8.21 x 102 kg/m³. The weight of the input piston is…

Q: What is the flow rate of a horizontal pipe whose intake diameter is 20 cm, and the constriction…

Q: A piece of wood is 0.600 m long, 0.200 m wide, and 0.075 m thick. Its density is 700 kg/m Part A…

A: Buoyancy Force: It is a physical quantity that represents the force induced in the upward direction…

Q: You wish to design a hydraulic lift such that it can lift a maximum load of 5000 kg. Your input…

A: given: F1min=50NF1max=100 NA1 = 1 mm2=1*10-6m2F2=5000kg*9.8 m/s2=49000 N we have to find A2max

Q: A barrel contains a 0.140-m layer of oil floating on water that is 0.255 m deep. The density of the…

A: Given:Height of oil layer on the water surface: H0 = 0.140mHeight(depth) of water : Hw =…

Q: 6. If a hydraulic pump had an input force from a piston of 10 N over an area of 10 square meters,…

Q: You fill a 5.0 x 103 m3 bucket with water that flows from a pipe of radius 1.25 cm. If it takes 14.0…

Q: The hydraulic lift's small piston with an area of 30 m^2 is subjected to a force of 100 N. To have…

Q: The maximum gauge pressure in a hydraulic lift is 17 atm. What is the largest size vehicle (kg) it…

A: Gauge pressure is P = 17 atm 1 atm = 1.013 × 10⁵ Pa = 1.013 × 10⁵ N/m² => P = 17 × 1.013 × 10⁵…

Q: The area of the small piston in a hydraulic jack is 0.75 m². The area of the large piston is 3.0 m2.…

Q: The maximum gauge pressure in a hydraulic lift is 17.0 atm. What is the largest-size vehicle (kg) it…

A: Given: The gauge pressure (P) in a hydraulic lift is 17 atm. The diameter (d) of the output line is…

Q: A force of F1 = 373 N is applied to a hydraulic jack pump piston with a diameter of D1 = 0.0177 m.…

A: Given data: Input force (F1) = 373 N Diameter of input piston (D1) = 0.0177 m Diameter of output…

Q: A horizontal pipe of 10 cm in diameter is connected to a pipe of 5 cm in diameter. Suppose the…

A: The diameter of the large pipe is d1=10 cm=10×10-2 m The pressure in the large pipe is p1=8×104 Pa…

Q: The input piston for a hydraulic lift in a garage has a radius of 0.010 m. The output piston has a…

Q: What force (in N) must be exerted on the master cylinder of a hydraulic lift to support the weight…

A: Given data: The mass of the car is M=2000 kg. The diameter of the master cylinder is dm=1.60 cm.…

Q: Water flows at a rate of 750.0 liters/min through a horizontal 5.90-cm diameter pipe under a…

A: Continuity equation,

Q: A force of 30. N is applied to the input piston of a hydraulic jack. If the input and output piston…

A: Given data: Force on input piston (F1) = 30 N Area of input piston (A1) = 0.20 m2 Area of output…

Q: A hydraulic jack has input piston with cross-sectional area 0.05 m2 and output piston with…

A: Given Data: The cross-sectional area of the input piston is: Ai=0.05 m2 The cross-sectional area of…

Q: A hydraulic lift has an input piston of area A and has an input force of 1000N. If the output piston…

A: Given- Force F1=1000NArea A1=AArea A2 =2A

Q: The small piston of a hydraulic lift has a cross-sectional area of 3 cm, and its large piston has a…

A: Given data The cross-sectional area of the small piston is As = 3 cm2. The cross-sectional area of…

Q: 2. Ethanol with a density of 789 kg/m? flows in the horizontal pipe 11.5m long. The entrance pipe…

Q: A hydraulic lift has a maximum gauge pressure of 15 atm. If the largest vehicle it can support has a…

A: Given data: Maximum gauge pressure, Pin = 15 atm Mass, m = 10000 kg Solution: Write the equation…

Q: A car of mass 800 Kg is hoisted on the large cylinder of a hydraulic press. The area of the large…

A: Given data: Mass of the car (m) = 800 kg Area of large piston (A2) = 0.35 m2 Area of small piston…

Q: A hydraulic jack has an input piston of area 0.0560 m2 and an output piston of area 0.750 m2. How…

A: input area, a = 0.056 m2 output area, A = 0.75 m2 Output force, F = 1.4 x 104 N

Q: What is the average flow rate in cm/s of gasoline to the engine of a car traveling at 106 km/h if it…

A: Explanation Average flow is defined as the volume consumed in unit time. So average flow rate is,…

Q: What is the pressure (kPa) at the bottom of an open cylindrical container filled with a fluid with…

Q: What will be the gauge pressure and absolute pressure of water at a depth 12m below the surface?…

Q: A 50 meter vertical column of liquid with density of 1596 kg/m^3 is located where g is 9.81 m/s^2.…

A: h= 50m , p= 1596 kg/m3 , g= 9.81m/s2

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, physics and related others by exploring similar questions and additional content below.

Similar questions

Is there a limit to the height to which an entrainment device can raise a fluid? Explain your answer.
Many figures in the text show streamlines. Explain why fluid velocity is greatest where streamlines are closest together. (Hint: Consider the relationship between fluid velocity and the cross-sectional area through which it flows.)
How much pressure is transmitted in the hydraulic system considered in Example 11.6? Express your answer in pascals and in atmospheres.
Suppose the master cylinder in a hydraulic system is at a greater height than the slave cylinder. Explain how this will affect the force produced at the slave cylinder.
What force must exerted on the master cylinder of a hydraulic lift to support the weight of a 2000-kg car (a large car) resting on a second cylinder? The master cylinder has a 2.00-cm diameter and second cylinder has 24.0-cm diameter.
Water towers store water above the level of consumers for times of heavy use, eliminating the need for high-speed pumps. How high above a user must the water level be to create a gauge pressure of 3.00105 N/m2?
Rank the buoyant forces exerted on the following five objects of equal volume from the largest to the smallest. Assume the objects have been dropped into a swimming pool and allowed to come to mechanical equilibrium. If any buoyant forces are equal, state that in your ranking. (a) a block of solid oak (b) an aluminum block (c) a beach ball made of thin plastic and inflated with air (d) an iron block (e) a thin-walled, sealed bottle of water
. A storage tank 30 m high is filled with gasoline. (a) Find the gauge pressure at the bottom of the tank. (b) Calculate the force that acts on a square access hatch at the bottom of the tank that measures 0.5 m by 0.5 m.
Figure 11.35(a) shows the effect of tube radius on the height to which capillary action can raise a fluid. (a) Calculate the height h for water in a glass tube with a radius of 0.900 cm—a rather large tube like the one on the left. (b) What is the radius of the glass tube on the right if it raises water to 4.00 cm?
. A dentist's chair with a person in it weighs 1900 N. The output plunger of a hydraulic system starts Do lift the chair when the dental assistant's foot exerts a force of 45 N on the input piston. Neglecting any difference in the heights of the piston and the plunger, what is the ratio of the area of the plunger to the area of the piston?
Oil having a density of 930 kg/m3 floats on water. A rectangular block of wood 4.00 cm high and with a density of 960 kg/m3 floats partly in the oil and partly in the water. The oil completely covers the block. How far below the interface between the two liquids is the bottom of the block?
Water emerges straight down from a faucet with a 1.80-cm diameter at a speed of 0.500 m/s. (Because of the construction of the faucet, there is no variation in speed across the stream.) (a) What is the flow rate in cm3/s? (b) What is the diameter of the stream 0.200 m below the faucet? Neglect any effects due to surface tension.