The quantity of air in a 900 mm diam duct is 15 m/s, the duct resistance is 7.1 Ns/m® and the air density is 1.20 kg/m³. The duct diameter increases to 1400 mm with a shock loss factor of 0.5. What is the end pressure (Pa gauge) with respect to the start. a 45 m'ls passes through a regulator. Using normal values for coefficient of discharge what open area is required for a pressure differential of 450 Pa ?

The quantity of air in a 900 mm diam duct is 15 m/s, the duct resistance is 7.1 Ns/m® and the air density is 1.20 kg/m³. The duct diameter increases to 1400 mm with a shock loss factor of 0.5. What is the end pressure (Pa gauge) with respect to the start. a 45 m'ls passes through a regulator. Using normal values for coefficient of discharge what open area is required for a pressure differential of 450 Pa ?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A compressor delivers 2000 cfm of air through a pipe at a receiver pressure of 140 psig. What minimum size schedule 40 pipe should be used if the pressure loss is to be limited to 0.10 psi per foot of pipe length?
Water (specific gravity, G, is 1.0 and the kinematic viscosity, ν, is 1.14 *10-6 m2 /s) flows through a piping system with a flow rate of 0.9 m3/s. The pipe is 2800 m long and 600 mm inside diameter. The pipe has three gate valves, two globe valves, one swing check valve, three standard teesthrough-branch, and four 90o standard elbows. Calculate the following: c- The Darcy friction factor if the pipe is fully rough and has an absolute internal roughness, e, of 0.01 mm.d- The frictional head loss in units of (m) using the Darcy equation.
A Forced - Draft (FDF) with open suction has rated capacity of 4,000 CFM at 1,800 rpm. The pressure developed at the discharged duct is 10 mm H2O. The discharge duct is circular with inside diameter of 600 mm. Calculate the following:a) what is the velocity of air at the discharge in mm H2O?b) what is the theoretical fan power required in kW?Consider standard density of water and air are 1000 kg/m3 and 1.20 kg/m
2. A centrifugal pump installation has been designed to discharge 0.126 ?3/? of brine (sp.gr. = 1.2). The suction pipe is 305 mm and is at the same level as the discharge pipe which is 203 mm in diameter. At the centerline of suction flange, the vacuum is 154.2 mm Hg. The discharge pressure gauge reads 0.1379 MPa and is connected 1.22 m above the discharge flange centerline. The pump is driven by a 35 KW electric motor that will not carry overload and has an efficiency of 82%. There is no significant head loss. The design conditions have changed, and is now desired to increase the capacity of the pump by increasing the speed. The motor is so designed that its speed maybe increased but its power cannot exceed its design rating. Assuming the pump efficiency to remain constant, how much can the pump capacity be increased without overloading the motor?
. What horsepower is supplied to air moving at 7m/min through a 70cmx90cm duct under a pressure of8cm of H2O?
Water (specific gravity, G, is 1.0 and the kinematic viscosity, ν, is 1.14 *10-6 m2 /s) flows through a piping system with a flow rate of 0.9 m3/s. The pipe is 2800 m long and 600 mm inside diameter. The pipe has three gate valves, two globe valves, one swing check valve, three standard teesthrough-branch, and four 90o standard elbows. Calculate the following:a- The total length of that piping system.b- Is the flow laminar or turbulent?
Grape juice is being pumped at 27ºC from an open tank through a sanitary tube (Di = 0.03561 m) for second tank on a higher level. The mass flow rate is 3 kg/s (ρ = 997.1 kg/m³) up to 60 m of linear pipe, with 2 standard 90º elbows (Cff = 1.5) and an angle valve (Cff = 2). the tank supply line maintains a liquid level of 6 m, and the grape juice leaves at a height of 6 m. 24 m above the ground. Calculate the efficiency requirements of the pump that has an efficiency of 65%.
A pitot-static tube is used with a mercury (SGHg =13.6) manometer tomeasure the flow of an inviscid fluid with SGf = 1 in a 4in diameter pipe. What is the flow ratethrough the duct?
The water is pumped from a 40 sch pipe that has 750 ft lenght, 6 in. nominal diameters. Height difference between exit and entry planes is stated as 50 ft. The yield of waterpump, 80% the power of pump motor is 20 horsepowers. Friction losses are stated as 50ft-lbf/lbm. Please calculate the flow rate in pipe line.
It is desired to meter methanol at 20°C flowing through a5-in-diameter pipe. The expected flow rate is about 300gal/min. Two flowmeters are available: a venturi nozzle anda thin plate orifice, each with d = 2 in. The differential pressuregage on hand is most accurate at about 12–15 lbs/in2.Which meter is better for this job?
Provide solutions A penstock with a diameter of 4 ft and length of 225 ft carries water (γ = 62.4 lbf/ft3) through a 200 ft drop from a reservoir to a turbine. The penstock entrance is 10 ft below the water surface. The ﬂow rate through the system is 500 cfs and water exits the turbine in a free jet with a velocity of 9 ft/s. The Darcy-Weisbach friction factor for the penstock is 0.01. Flow is turbulent and head losses at the entrances and exits of the penstock and turbine are negligible. (a) Draw the hydraulic grade line and energy grade line. Label transitions points with the height change using symbols (e.g. hL for pipe head loss) (b) Determine the head delivered to the turbine by the water in ft.(c) If the turbine and generator have a combined eﬃciency of 80%, determine the power in hp generated by the system.
Oil at 24 gpm and 1200 psi enters the low-pressure inlet of a 4:1 Racine pressure intensifier. Find the discharge flow rate and pressure.